Showing results: 286 - 300 of 318 items found.
-
DUH-210/DUH-210S -
Shimadzu Corp.
A new evaluation system for measuring the material strength of micro regions, such as semiconductors, LSI, ceramics, hard disks, vapor deposited films, and thin coating layers, not addressed by previous hardness testers. It can also be used to evaluate the hardness of plastics and rubbers. This instrument uniquely measures dynamic indentation depth, not the indentation after the test. This in turn permits measurement of very thin films and surface (treatment) layers that are impossible to measure with conventional methods. Additionally, this same method supplies the data needed to calculate elastic modulus on the test specimens.
-
Model 3911 -
Jinan Testing Equipment IE Corporation
For indirect tensile testing, such as for resilient modulus, these extensometers measure the lateral deformation of specimens. They are self-supporting on the sample and clip on in seconds. The traditional way this deformation has been measured was prone to errors caused by slight rocking of the sample as it is loaded. The self-supporting design of the Model 3911 eliminates this problem. This unit will handle the dynamic pulse requirements of resilient modulus testing.The speed of mounting makes test set-up much faster than with the older method. The pivot mounting used ensures that the specimen contact pads meet the often uneven asphalt surface as well as possible. The measuring range options available allow a wide range of testing, yet can easily measure the sometimes very small displacements required.The Model 3911 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
CST-300/200 -
Jinan Testing Equipment IE Corporation
The Compression and Flexure Testing Machine is mainly designed for compression and bending tests of cement & mortar specimens. The Compression and Flexure Tester for Current can finish compression and flexure tests automatically by one-key action . Computer & software are also adopted to make the operation even easier. With new design and advanced technology, the series of Compression and Flexure Testing Machine have more advantages in appearances operation & applications. The Compression and Flexure Tester for Cement is an ideal tester for quality control at industrial & mineral enterprises, teaching in high schools, and technology researching al scientific industries.
-
Qualitest International Inc.
Qualitest offers Charpy / Izod Impact Testers with capacities up to 750J meeting and exceeding ASTM E23, ISO, DIN, JIS, standard requirements. The key benefits of this line of top technology models are price competitiveness, extremely high precision and durability, automatic motorized lifting of the pendulum hammer to optimize cycle times, flexibility, efficiency for low/high temperature testing, and much more. Optionally we offer temperature chambers, automated sample handling, centering device, Charpy sample preparation and broaching machines for preparation of notched bar specimens.
-
SEM -
Materials Evaluation and Engineering
JEOL JSM-6610 LV LaboratoryScanning electron microscopy (SEM) uses electrons for imaging to obtain higher magnifications and greater depth of field than light microscopes. The instruments at MEE are capable of variable-pressure, or low vacuum, SEM (VPSEM), as well as traditional high-vacuum conditions for sample observation. VPSEM is a specialized method using a variable-pressure sample chamber that allows direct evaluation of samples that are not readily examined with a traditional high-vacuum SEM. Nonconductive or vacuum sensitive samples that would typically require additional sample preparation can be directly analyzed in VPSEM without the need for additional sample preparation, such as carbon or metallic conductive coatings. This reduces both sample preparation time and distractions in microanalysis. Our laboratory also has a field emission SEM (FESEM) for critical high-magnification work and low-voltage (LVSEM) applications. Each instrument has a spacious sample chamber that can accommodate large and irregularly-shaped specimens and accessories for feature dimensional analysis and chemical microanalysis.
-
infraTest Prüftechnik GmbH
For automatic compression of simple and modified Proctor specimens 100 and 150 mm. Stand model for installation on a stable surface with CE safety door in accordance with the EU Machinery Directive. The Proctor mold used for the respective test is placed on the rotatable base plate and the corresponding monkey hammer inserted into the lifting device. Exchangeable drive disks and cams control the drop height and the rotary feed rate after each stroke. The displacement of the impact surface sample edge / center / sample edge is done by an electric drive. The entire compaction process is microprocessor-controlled with universal software and preselectable test parameters:
-
Instron
During tests carried out on servohydraulic machines, elements of the system are subject to acceleration. As a result, in addition to the force applied to the specimen, the load cell also reads forces resulting from its own movement and the mass of the grips and fixtures attached to it. Dynacell is the world's first truly dynamic load cell, designed from the outset for measuring dynamic loads. Dynacell introduces the following advantages:*Reduces dynamic load errors which can be a significant percentage of reading *Increases productivity by allowing higher frequency operation while maintaining test validity *Improvements such as doubling the frequency are common
-
FVMPE-RS -
Olympus Corp.
The Olympus FVMPE-RS multiphoton imaging system is purpose-built for deep imaging in biological tissue, aimed at revealing both detail and dynamics. Innovative features for efficient delivery and detection of photons in scattering media enable high signal-to-noise ratio acquisition. This translates to bright images with precise details — even from deep within the specimen. High sensitivity is matched with high-speed imaging to capture rapid in vivo responses. For advanced applications, dual-wavelength excitation extending to 1300 nm is available. Independent control of visible or multiphoton laser light stimulation and the ability to synchronize with patch clamp data are also possible.
-
Handheld Hardness Testers -
Qualitest International Inc.
Handheld Hardness Testers are ideal hardness testing tools where large samples, which cannot be brought to a traditional tabletop hardness tester, or specimens with hard to access areas are to be tested. A wide variety of the portable hardness testers, offered by Qualitest ensure that we recommend the most suitable model for your application. The extensive selection of our handheld hardness testers is available from low-cost economy models up to advanced models coming with more features. These models can measure the hardness of your materials in Rockwell, Superficial Rockwell, Brinell, Vickers, Webster, Barcol scales and often conversions can be done.
-
32-76 -
Testing Machines, Inc.
Testing Machines Inc., is globally recognized as the leading supplier of Coefficient of friction instrumentation. Our NEW 32-76 coefficient of friction tester uses advanced digital force signaling and high speed data acquisition software providing unmatched precision and repeatability in COF testing. Improved features include a color touchscreen display and intuitive software user interface for easy navigation and test method storage. Based on the horizontal plane method, coefficient of friction and Slip properties aid in the evaluation of chemicals and additives used to create, monitor or minimize the degree of friction between two contacting test specimens or surfaces.
-
Instron
CEAST VisualIMPACT software is designed to control CEAST Pendulums and Drop Tower Series, manage tests and offer a user-friendly interface when using the Data Acquisition System. It records force and absorbed energy data related to impacts, visualizes and helps analyze the results and calculates resilience. The operator is guided through parameters setup by means of tables describing strikers and specimens that are filtered according to the test type and international standard selected. In the case of instrumented tests, many possibilities for data analysis and visualization are made available. The results are shown through comprehensive and customizable graphs and can be filtered by break type (only specimens with a selected break type are shown). Working with groups of test, the software performs a statistical analysis, and the operator can pick and discard single test results. Different measurement units can be selected. It is possible to print reports and to export data totally or partially. Recent improvements include the possibility to set a number of user profiles, including graphic settings, default printing options, advanced parameters for data analysis and so on, switching quickly from one another when looking at results. The introduction of a new Data Acquisition System (CEAST DAS 64K) in the Impact product line has also triggered a number of new capabilities for the SW, which is now able to process a more comprehensive calibration file for instrumented tups and hammers and manage DAS configurations with a wider range of data acquisition channels.
-
Sataton Instruments Technology CO., Ltd
Moisture management tester (MMT) is the tool for the measurement, evaluation and classification of liquid moisture management properties of textile fabrics. By testing the changes in electrical resistance of textiles placed between two horizontal electrical sensors with concentric pins, the tester can calculate fabric liquid moisture content changes that quantify dynamic liquid moisture transport behaviors in multiple directions of the specimen. The software of tester can grade the liquid moisture management properties of a fabric by using the predetermined indices. The tester is used to determine the liquid moisture management properties of knitted, woven and nonwoven textiles, and also can be used to test the one-way transport capability of diapers.
-
National Technical Systems
NTS has extensive abilities in fluid testing. We’ve tested a large variety of products, from pipe fittings to process controllers, flexhoses to pressure vessels, valves to actuators, tank liners to heat exchangers, water to Skydrol. We have tested these products for a variety of measurements, from viscosity to flash point and auto ignition, among others. NTS fluids testing facilities are equipped with computerized data acquisition, reduction and analysis equipment for monitoring the functional characteristics of specimens during testing. NTS has considerable expertise in high flow testing of small devices – such as meters, indicators, totalizers, sensors, transmitters, and check valves.
-
Dongguan Kejian Instrument Co., Ltd.
1. Meet ISO,ASTM, DIN,JIS,SAE,BS,ANSI,GM,U.S.GOVT(ASTMG153,ASTMG154,,ASTMD4329,ASTMD4977,ASTMD4587,SAEJ2020,ISO4892)2. QUV condensation device simulates the effect of humidity of outdoor,meeting 100% humidity.3. Electronic-eye irradiance control system4. Use blackboard temperature sensor providing precise temperature and recuring test result.5. Perform humidifying, condensation and water spraying circulating test.6. Irradiance is calibrated by CR-10 calibrator and automatic calebration procedure.(Paten technology)7. Specimen size and quantity: 75mm×300mm 24pcs, 75mm×150mm 48pcs
-
WTT Series -
Jinan Testing Equipment IE Corporation
WTT series metal wire torsion tester is mainly used in a metal factory to test the plasticity of metal wires and ropes under torsion condition. Surface flaws of steel wires may be shown during the testing process. The revolution is displayed on a 4- digit LED, with the max. revolution value displayed as 999.9. The revolution value is automatically held at the break of specimens. With computer & software, the Metal Wire Torsion tester can realize automatic control. The Metal Wire Torsion tester conforms to standard ASTM A938, ISO7800. The Metal Wire Torsion tester is an ideal QC tool for Quality Inspection & Control Department related to steel wire application.
