Showing results: 46 - 60 of 71 items found.
-
NOA-7100 -
Shimadzu Corp.
The NOA-7100 adopts the normal pressure chemiluminescence method is adopted for NOx measurement, and the zirconia method is adopted for O2 measurement. NOA-7100 is “All-in-one portable analyzer” that incorporates the pretreatment parts needed for measurements. Switching between eight ranges from 25 to 4,000 ppm supports a wide range of NOx measurements. The NOA-7100 has wireless communication capability, so measurement values and charts can be displayed on PCs or smart devices. And measurement data can be exported using a USB flash drive.
-
ABex AM-307 FR-NXG Flashrunner -
Konrad Technologies GmbH
The ABex AM-FR-NXG incorporates the FlashRunner LAN 2.0 Next Generation from SMH Technologies. The FlashRunner is used to program microcontrollers, flash and other logic and memory devices. All DIO’s, the programmable voltage lines and the corresponding ground lines can be switched by relays.The ABex AM-FR-NXG is equipped with an onboard Ethernet Controller which connects the FlashRunner directly to the PXIe Backplane of the ABex Chassis. Using a windows host, each AM-FR-NXG will provide its own network adapter.
-
UFS -
Arasan Chip Systems, Inc.
Universal Flash Storage (UFS) is a JEDEC standard for high performance mobile storage devices suitable for next generation data storage. The UFS is also adopted by MIPI as a data transfer standard designed for mobile systems. Most UFS applications require large storage capacity for data and boot code. Applications include mobile phones, tablets, DSC, PMP, MP3, and other applications requiring mass storage, boot storage, XiP or external cards. The UFS standard is a simple, but high-performance, serial interface that efficiently moves data between a host processor and mass storage devices. USF transfers follow the SCSI model, but with a subset of SCSI commands.The Arasan UFS IP family consists of Host controller IP, Device controller IP, and MPHY.
-
Das Test Haus
Services for ASIC houses and Integrated Device Manufacturers are IC Wafer / Final Test, IC assembly, Test Program development, product engineering, Flash / EEPROM programming, characterisation / capability studies, yield enhancement, design verification and failure / yield analysis. Das Test Haus are specialists for wafer test, low power, mixed signal and eeprom test.
-
CGT-7100 -
Shimadzu Corp.
The CGT-7100 analyzer measures the concentration of gases in a continuous way, using a ratio photometric non-dispersive infrared absorption (NDIR) method. All pretreatment parts required for measurement, such as the pump, filter, and electric dehumidifier, are built-in. The analyzer can measure three components including CO, CO2, or CH4 (any two of these) and O2, and is compatible with measurement at 100 vol%. The CGT-7100 has wireless communication capability, so measurement values and charts can be displayed on PCs or smart devices. And measurement data can be exported using a USB flash drive.
-
Accsense, Inc
Our new Accsense VersaLog series of monitoring and alarming devices provide your project with highly accurate data capture and several connection options. With most models recording on 7-8 channels, Accsense VersaLog monitors many parameters including temperature, humidity, current/voltage, strain, and also offers connection with thermistors for extreme accuracy. These dataloggers also support USB, Serial port and Ethernet connections for local and remote access and store readings on a 4MB flash memory. Download, plot and analyze your data with the feature-filled Siteview software.
-
RA2 -
Renesas Electronics Corp.
The RA2 Series is the RA Family's entry-level 32-bit MCU, offering excellent cost performance and ultra-low power consumption. It delivers up to 48MHz of CPU performance using an Arm® Cortex®-M23 core with up to 256kB of embedded flash memory and a wide single voltage supply range from 1.6V to 5.5V. With cutting-edge peripherals like capacitive touch, the RA2 Series is ideal for system control or user interface applications such as in healthcare devices, home appliances, office equipment, and measuring equipment.
-
Xeltek
Until now,Support 401 IC manufacturer, 103004 pcs devices and keeps growing.Features:Supports 87454 types of devices from 305 IC manufacturers (by 3/15/2013) and keeps growing.Supports EPROM、Paged EPROM、Parallel and Serial EEPROM、FPGA、PROM、FLASH(NOR & NAND)、BPROM、NVRAM、SPLD、CPLD、EPLD、Firmware HUB、Microcontroller、MCU;Supports devices with Vcc as low as 1.2V. Socket Adaptors available for DIP、SDIP、PLCC、JLCC、PGA、LGA、SOIC、SOJ、SOT、QFP、TQFP、PQFP、VQFP、MQFP、LQFP、TSOP、SOP、TSOPII、PSOP、SSOP、TSSOP、SON、EBGA、FBGA、FTBGA、VFBGA、μBGA、CSP、SCSP、QFN、HVQFN etc.High programming speed.Built with 144 universal pin-drivers. Universal adaptors are available for varies packages up to 144 pins. Quick new device support. Popular NAND FLASH Platform supported including Samsung (XSR1.0/1.6), QualComm, HYNIX(HIFFS), MTK(Solution V1.1), ICERA (v1.0/2.0), ST (7162、7141等), AMLOGIC(IF2/0), REALTEK, PICOCHIP, DataLight ( Flash FX Pro), Marvell(310/303/920/935…), BroadCom, ZTE, Intel (CE4100),UBI, LEADCORE(L1809OG), MSATR etc. Customer-specific NAND solution available.PC hosted mode and stand-alone dual modes. Under PC hosted mode the programmer is controlled by a PC via USB2.0 (high speed) to program a chip. Under stand-alone mode the programmer is controlled via a 6-KEY keypad and a 20 character by 4 line LCD display. A CF card is used to store the project files.User can operate multiple units to construct a concurrent multiprogramming system thank for the stand-alone mode. IC manufacturer approved programming algorithms are used for high reliability.Testing functions for logic devices.Advanced and powerful software functions.Production mode starts chip operation at the moment the chip is inserted in the socket properly.Project function simplifies processes such as device selection, file loading, device configuration setting, program option, and batch file setting into one touch step.Password can be set for project files and production volume controlBatch command combines device operations like program, verify, security into a single command at any sequence.Dynamic buffer makes it possible that each chip is programmed with different data file. Applications including serial number, MAC address etc.Log file is useful for quality tracking.Many safety mechanisms are built including self-diagnosis, wrong chip placement detection, poor-pin-contacting detection, ID checking, over-current and over-voltage protection etc.Windows XP/Vista/Win7/ Win8/Win10 compatibility.
-
AI-7280 -
Advent Instruments Inc.
The AI-7280 is a highly flexible central office line simulator. It is designed primarily for the testing and verification of common terminal equipment, including standard telephones, Caller ID devices, SMS (Short Message Service) capable equipment, and any device using an analog Tip/Ring interface circuit. Supplied with the TRsSim software for Windows, it can analyze a telephone''s DTMF characteristics, pulse dialing and flash timing, generate various network tones and ringing patterns. Both Type I (on-hook) and Type II (off-hook) Caller ID is supported using either FSK or DTMF data transmission. As an optional component, the TRsSim software can perform SMS testing to either the ETSI protocol 1 or protocol 2 standards.
-
Black Magic Probe V2.3 -
Black Magic Debug Probe
In most cases Black Magic Debug takes the form of a firmware for the Black Magic Probe hardware, and implements a GNU DeBugger (GDB) server.The Black Magic GDB server features: - Automatic target detection- No need for target specific configuration scripts- All protocol and target specific control is done through GDB monitor commands- No “software in the middle” like OpenOCD required- Easily scriptable thanks to the GDB scripting capabilities- Interface to the host computer is a standard USB CDC ACM device (virtual serial port), which does not require special drivers on Linux or OS X.- Targets ARM Cortex-M and Cortex-A based microcontrollers- Provides full debugging functionality, including: watchpoints, flash memory breakpoints, memory and register examination, flash memory programming, etc.- [Semihosting / Host IO support] as well as [Serial Wire Debug TRACESWO support].- Implements USB DFU class for easy firmware upgrade as updates become available.- Works with Windows, Linux and Mac environments.
-
USB Multilink ACP -
P&E Microcomputer Systems
P&E’s USB Multilink ACP is a debug probe which allows a PC/laptop access to JTAG/SWD on ARM Cortex devices from several manufacturers (see complete list below). It connects between a USB port on a Windows machine and the standard debug connector on the target. The product photos to the left of this page show how the headers can be accessed by simply flipping open the plastic case. Ribbon cables suitable for a variety of architectures are included. By using the USB Multilink ACP, the user can take advantage of the debug mode to halt normal processor execution and use a PC to control the processor. The user can then directly control the target’s execution, read/write registers and memory values, debug code on the processor, and program internal or external FLASH memory devices.
-
Raspberry PI Foundation
The Compute Module Development Kit 3 is a prototyping kit for those who wish to make use of the Raspberry Pi in a more flexible form factor, intended for industrial applications. The compute module contains the guts of a Raspberry Pi 3 (the BCM2837 processor and 1GB RAM) as well as a 4GB eMMC Flash device (which is the equivalent of the SD card in the Pi). The accompanying IO Board is a simple, open-source breakout board that you can plug a Compute Module into. The board hosts 120 GPIO pins, an HDMI port, a USB port, two camera ports and two display ports.
-
National Technical Systems
NTS has extensive abilities in fluid testing. We’ve tested a large variety of products, from pipe fittings to process controllers, flexhoses to pressure vessels, valves to actuators, tank liners to heat exchangers, water to Skydrol. We have tested these products for a variety of measurements, from viscosity to flash point and auto ignition, among others. NTS fluids testing facilities are equipped with computerized data acquisition, reduction and analysis equipment for monitoring the functional characteristics of specimens during testing. NTS has considerable expertise in high flow testing of small devices – such as meters, indicators, totalizers, sensors, transmitters, and check valves.
-
Xeltek
※ Four Pick & Place nozzles, Eight socket pressing actuators and 2 tape feeders※ High throughput up to 2400UPH※ Embeded with eight ultra-high speed programmers SuperPro / 7500, each with up to 4 sockets, totally 32 sockets. Throughput 60 times higher than SuperPro / SB01 for eMMC devices※ Supports over 80,000 devices from over 300 IC manufacturers※ Supports tray, tape and tube input and output. Supports laser and ink marking※ Short change-over time※ Intelligent s/w cuts learning curve and setup time, makes task management an easy job※ Compact sizeHigh throughput:4 nozzles, 8 independent socket pressing actuators and 2 tape feeders. Up to 2400 UPH for devices with programming time less than 50 sec. Throughput 0.6 to 60 times higher than SuperPro/SB01, especially higher for large capacity devices like eMMC, NAND /NOR FLASH,SPI FLASH. Suitable for both small and large capacity devices. Prog. Time (S) 50 60 120 180 240 300 UPH (unit per hours) 1600 1600 840 560 420 336 Accurate positioning:Equipped with high performance servo system, precise CCD cameras and vision algorithm for device alignment and sockets / pick & place spots positioning.High performance programmers: 8 ultra-high speed universal gang programmers SuperPro/7500 resident. Each with up to 4 sockets, totally up to 32 sockets in the system. Supports up to 100,000 devices from over 300 IC manufacturers and growing.Varied I/O devices:Supports tray, tape and tube input and output. Supports laser and ink marking. Supports packing conversion and can work as a packing conversion machine alone.Short change-over time:I/O devices and socket adaptor are easy to be changed when programming task need to be changed. Socket positioning can be performed automatically. Projects can be loaded automatically with barcode scanning.Powerful and intelligent software:Setup data saved for next operation, log file and statistic reports for quality and yield traceability, flexible sockets prohibition strategy promises high yield rate for unattended operation, graphical user interface cuts learning curve, prevents chip over-lapping by socket checking before chip placing.Remote Control:Remote project loading, quality monitoring, volume control, file security.
-
ASC-5216 -
Avantes Inc.
The ASC-5216 is the smallest OEM electronics board Avantes offers. It can be used with the Sony (ILX511, ILX554B) and Toshiba (TCD-1304) CCD detectors. Featuring the same powerful 5126 Coldfire processor as used in the AS-5216, it's equipped with a Hirose ST60-36p connector. It has 12 programmable IO ports (3 DI, 9 DO), 2 analog out ports and 2 analog in ports. One digital out port is used for controlling the flash rate of an external Xenon strobe (AvaLight-XE), one digital out port is used to control external TTL-shutter devices, one digital output is reserved for external control for flashing a laser source in LIBS applications. One digital in is used for external hardware triggering.