Showing results: 121 - 135 of 209 items found.
-
Keysight Technologies
The 34980A System and Control modules provide additional measurement and control capabilities that are typically used in test applications. Choose from modules that include digital I/O with programmable polarity, D/A converter with onboard memory to create waveforms, and frequency counter/totalizers.
-
FV-1500 -
Ono Sokki
FV-1500 High-speed F/V Converter is a frequency-to-voltage (current) converter that converts frequency signal proportional to rotation speed, moving speed, etc. into voltage signal.The FV-1500 is designed to accommodate the needs of high speed rotation measurement including rotating motors used in HV/EHV production lines etc. It also contributes to measure rising characteristics, very small fluctuation in steady rotation, and transient phenomena of flow speed with fast response.
-
Analog Devices Inc.
RMS-to-DC converters manufactured by Analog Devices are used in a wide variety of applications where precision and low power measurement of ac signals is the prime objective. An ADI rms-to-dc converter offers real time measurements, meaning there are no latency issues such as those that limit the frequency response of other technologies—the dc output is simply the equivalent of the rms input, over a wide range of input frequencies, and for complex waveforms not limited to sine waves. ADI offers a wide range of rms-to-dc converters optimized for the most demanding performance, power, and cost applications satisfying true rms needs.
-
ZRXL-Series -
Radiometer Physics GmbH
The RPG ZRXxxxL millimeter-wave receiver are optional for the following four-port vector network analyzers: R&S®ZVA24, R&S®ZVA40, R&S®ZVA50 or R&S®ZVA67, and R&S®ZVT20 (not suitable for RPG ZRX500L) with at least four ports. The converters facilitate measurements in the millimeter-wave frequency range. The RPG ZRXxxxL millimeter-wave receiver are available for the frequency bands from 50 GHz to 75 GHz (RPG ZRX75L), from 75 GHz to 110 GHz (RPG ZRX110L), from 220 GHz to 330 GHz (RPG ZRX330L) and from 330 GHz to 500 GHz (RPG ZRX500L). Other frequency bands are covered by other models from the RPG ZRXxxx receiver or R&S®ZCxxx converter series.
-
ZET 302 -
ZETLAB Company
Digital USB oscillograph ZET 302 is used for high-frequency signals control in the range up to 20 MHz. Implementation of 50 MHz ADC converter along with equivalent sampling mode use allows to increase effective frequency up to 500 MS/s.
-
S96082A -
Keysight Technologies
The S96082A offers the solutions for measuring mixers/frequency converters and amplifier's harmonics using the ENA. The frequency offset mode (FOM) provides the capability to tune the ENA's receivers to different frequencies from the source. This enables measuring amplifier's harmonic responses and mixer/converter's conversion loss.
-
Keysight Technologies
The PNA Series of network analyzers offers industry-leading performance for testing amplifiers, mixers, and frequency converters. Built-in pulse modulators and pulse generators provide pulsed S-parameter measurements quickly and accurately. All models are available in two-port single-source and four-port dual-source versions.
-
TSCT (Average Sensing) / TFCT (TRUE RMS) -
Kusam Electrical Industries Limited
• Transform Input: AC 5~400A directly into DC 4~20mA, no need external CT.• Suitable for application with high waveform distortion :(Frequency converter, Motor, SCR )• High accuracy <0.5%• High response time• High stability, easy connection.
-
N4377A -
Keysight Technologies
The N4377A Lightwave Detector is a USB-powered optical-electrical converter with built-in optical power meter capability. If used with a vector network analyzer or a spectrum analyzer it enables frequency domain applications in photonics.
-
Behlman Electronics Inc.
Behlman’s RR series of Railroad Signal Sources and Frequency Converters are low cost, highly reliable, switch mode units built for Railroad Signaling. The RR series can be supplied with any single or three-phase input and outputs a clean, regulated AC signal at a precise frequency from 25 Hz to 250 Hz. These rugged signal sources are built to support the rigors of operating in the harsh environment of Railroad signaling equipment.
-
Bourns
Bourns Miltilayer chip inductors offer high frequency, nickel barrier, monolithic construction for high reliability, and magnetically shielded construction providing low radiation. They are well-suited for DC-DC converters, and prevention of electromagnetic interference to signals on the secondary side of electronic equipment, among many applications.
-
ADF-QMx44 -
Delphi Engineering Group, Inc
The DEG ADF-QMx44 FMC leverages the Analog Devices AD9081 MxFE (Mixed Signal Front End) transceiver technology. This highly integrated device includes a quad 16-bit, 12 Gsps sample rate radio frequency (RF) digital-to-analog converter (DAC) and a quad 12-bit, 4 Gsps rate RF analog-to-digital converter (ADC). The ADF-QMx44 features an 8-lane, 24.75 Gbps JESD204C transceiver port, an on-chip clock multiplier, digital signal processing capability and supports four transmitter channels and four receiver channels.
-
ADF-QMx42 -
Delphi Engineering Group, Inc
The DEG ADF-QMx42 FMC leverages the Analog Devices AD9082 MxFE (Mixed Signal Front End) transceiver technology. This highly integrated device includes a quad 16-bit, 12 Gsps sample rate radio frequency (RF) digital-to-analog converter (DAC) and a dual 12-bit, 6 Gsps rate RF analog-to-digital converter (ADC). The ADF-QMx42 features an 8-lane, 24.75 Gbps JESD204C transceiver port, an on-chip clock multiplier, digital signal processing capability and supports four transmitter channels and two receiver channels.
-
LS-27-D -
Lumistar Inc.
The Lumistar LS-27-D3 TwoChannel Quad Band PCI Down Converter product is a 3rd generation high-density, high performance down converter designed using the sameadvanced technology as in the industry leading LS-25 PCIReceiver. The down-converter converts one or two independent channels of up to four RF frequency bands down to a 70 MHz IF output. The LS-27-D3 is typically used in conjunction with theLumistar LS-35 Series Digital IF Receiver/Combiner to provide one or two independent telemetry receivers, or a dual diversity combining receiver, with up to two multi-mode demodulators and bit synchronizers in a two-slot PCI interface. The number of channels and frequency band designations can be specified at the time of order. Please see the data sheet for the LS-35-R Digital IF Receiver/Combiner for more information.
-
AtlanTecRF
Atlantic Microwave Converters are designed for Satcom test applications that offer a cost-effective solution for converting from L-band to all common Satcom uplink frequencies. All models incorporate fundamental frequency phase locked oscillators and double balanced mixers and can be remote mounted with DC supplied on the L-band RF input.