Showing results: 361 - 375 of 623 items found.
-
HVSCM -
Test Electronics
Designed to be used with the Model HVST High Voltage Surge tester. The Surge Current Monitor allows simultaneously surge testing 20 units. The Surge Current Monitor monitors the current going through each unit under test at the time of the surge. If a unit under test breaks down or leaks, the Surge Current Monitor will identify the bad unit by lighting the corresponding LED. The most important features of the surge tester are its ability to test the entire winding insulation system. A high voltage surge generates turn to turn, coil to coil, and phase to phase voltage stress, as well as ground insulation stress. When used as a dielectric test, accurate voltage readings are essential. The HV Surge Tester monitors the voltage directly across the winding under test. In production testing we expect that most of the time the devices will pass. In the event that one should fail, the failed device would be removed and then all the parts would have ot undergo another surge test. Since most devices pass most of the time, simultaneous surge testing can be a real time saver.
-
National Technical Systems
Will your product operate in a highly volatile environment without creating ignition and causing an explosion? Explosive atmosphere testing provides vital information about motors, lighting systems, bilge pumps, aircraft components, electronics, and other systems. Explosive atmosphere testing determines whether a product will be able to operate properly in a fuel contaminated, highly volatile environment without creating ignition and causing an explosion. Causes of ignition vary from tiny electrical arcs in battery-operated equipment to hot spots on surfaces of sealed, encased units, to sparks from other mechanical sources.
-
Instron
Instron® High-Temperature Extensometers are perfect for testing advanced composites, metals, polymers and other materials at elevated temperatures. This series incorporates a capacitive sensor that does not require any cooling. The extensometers come standard with a sensor conditioner unit providing a 0-10 V output with exceptionally low noise. These extensometers can be attached to round and flat specimens to perform tensile, compression, and cyclic tests.
-
TX-MT-100 SERES -
Test-X Fixture Products
Test-X MT-100 Series mechanical kits are an inexpensive solution for testing smaller printed circuit boards and other devices.The MT-100 Series features a 1/2" thick FR4 probe plate and a 3/8" thick Lexan top plate. Precision alignment is assured through tooling holes in both the probe and top plates. Units are available with a 2-1/2" pan or an upper head assembly
-
PM23 and LS20DV -
KD Optics Ltd.
The PM23 and LS20DV power meter and LED source are top of the range units for multimode testing of multimode libre links. The PM23 power meter is also calibrated as standard at 1550nm making it suitable for measuring singlemode links when used in conjunction with a suitable source. The LS23DV has 850nm and 1300nm switchable outputs from 1 port and a visible tracer from the other.
-
Corelis, Inc.
Corelis offers support for a variety of devices and instruments from third-parties in an effort to provide existing test platforms comprehensive JTAG test execution with Corelis ScanExpress software products. Supported instruments include National Instruments PXI-655x HSDIO and Teradyne Di-Series modules. Corelis also provides support for JTAG testing with FTDI FT2232 ICs embedded on a unit under test (UUT).
-
Keystone Compliance
Keystone Compliance offers temperature testing and temperature & humidity testing in chambers ranging from small bench top to large drive-in systems. Our largest chamber has inside dimensions of 12’ wide x 15’ long x 10’ tall and an 8’ x 9’ door. However, we have created custom oversized temperature chambers to accommodate much larger devices including cars, drones and large pieces of machinery. If you have a large unit, we can likely find a way to test it. Keystone Compliance is capable of moving, installing, and testing multiple rack assemblies. Our other large walk in temperature test chamber is equipped with twin 30 hp compressors and is capable of temperature transition rates exceeding 15 degrees Celsius per minute. This chamber permits temperature cycling testing on large items with aggressive transition times.
-
CI Systems Inc.
CI Systems' CCD test stations are used to carry out all the necessary tests to verify and compare the quality of a CCD based camera. These stations are based on CI Systems' reflective collimators, Visible Radiation Sources, special targets and integrated software, to project standard patterns with known geometry and intensity to the Unit Under Test. As a result, these stations are turnkey solutions for the CCD camera testing needs.
-
SOLAR I-Ve -
HT Italia Srl
SOLAR I-Ve allows both testing a single-phase (three-phase with optional MPP300) photovoltaic system and verifying I-V curve. Thanks to remote unit SOLAR02, it is possible to test the system complying with the requirement of simultaneity as provided for by the reference standard. SOLAR02 is a datalogger which, synchronized with SOLAR I-Ve, acquires the data relevant to irradiation and temperature while tests carried out by SOLAR I-Ve are carried out.
-
Compact Instruments
Force gauges provide a quick and reliable way to obtain a measure of force in tension and compression. DMV UK offer a comprehensive range of mechanical and digital force gauges with selectable units and peak force capture with capacities from 2 N to 100,000 N. All gauges are supplied with standard accessories, a 2 year warranty, and can be used for force testing in hand held or test stand applications.
-
Maxi-Burn -
MaxiTest LLC
The MaxiBurn Tube Preheater is a 2U rack mountable or bench top unit for heating 30 Octal Base Tubes. Designed for continuous use heating standard power pentodes to normalize their characteristics before testing or matching the MaxiBurn powers the tube filaments and drives a nominal plate current through each tube. Normal function of each tube is indicated by a glowing LED associated with the tube.
-
LPSU series -
AWT Global
LPSU series high power, low PIM switch units combine 65 low PIM ports or 14 low PIM ports. These switch matrices are designed in testing situations that require multi-band PIM sources, components or antennas. Combinations of multi-band PIMtesting are now easily possible, improving workflow significantly. LPSUs can be integrated in existing production control systems. Frequency range 698-2700 MHz.
-
Olympus Corp.
DELTA Lead Based Paint Handheld XRF Analyzers test for Lead (Pb) in seconds. These reliable, tube-based units are light in weight and ergonomically designed for all-day testing. They start fast and stay fast - no isotope fade. And, they have a low total cost of ownership. Before you begin structural repair - grinding, cutting or painting - screen for Pb; then, check your work area after clean-up.
-
Promet International Inc.
Our team works closely with your design team to develop a custom, long-term production solution that fits your specific program. Our manufacturing niche is in low- and mid-volumes (10 to 1,000 units) for assemblies with demanding or non-standard optical performance requirements. Along with Promet’s rigorous QC protocols, our in-house testing labs and engineering support ensure a well-controlled process and predictable results.
-
T020-001-ST62 -
Tripp Lite
The T020-001-ST62 FC to ST 62.5/125 Adapter converts a native FC fiber female port on the Tripp Lite T020-001-PSF Multi-Function Optical Fiber Cable Tester to an ST female port for 62.5/125 multimode cable testing. “62.5/125” is clearly labeled on the unit to differentiate the T020-001-ST62 from other adapters. Included dust caps keep the connectors clean when not in use.
