Filter Results By:
Products
Applications
Manufacturers
General Purpose Switch
is an array of uncommitted relays. AKA: General Purpose Switching
See Also: Switching, Switching Matrix, High Voltage Switching, Switching Matrices, Multiplexers
- Pickering Interfaces Ltd.
product
PXI/PXIe RF Switch, Hex SPDT, 3GHz, 50Ω, SMB
40-870A-006
The 40-870A-006 (PXI) and 42-870A-006 (PXIe) are 50Ω RF switches with 6 separate SPDT relays in a single slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz. The injection of noise and unwanted signals into the signal paths of the 40/42-870A has been minimized by careful attention to the mechanical and electrical design.
-
product
64-Channel Form A General Purpose Switch for 34980A
34939A
The Keysight 34939A is a high density general-purpose switch module for the 34980A Multifunction Switch/Measure Unit. It has 64 independent single-pole, single-throw (SPST) relays that can switch 1A and carry 2A. This module can be used to cycle power to products under test, control indicator and status lights, and to actuate external power relays and solenoids. The relays are 100V, 1A contacts and can handle up to 60W. Standard 78-pin Dsub connectors allow for use with standard cables, screw terminal blocks, or mass interconnect solutions.
-
product
Keysight 32-Channel FormC/Form A General Purpose Switch for 34980A
34937A
The Keysight 34937A is a general-purpose switch module for the 34980A Multifunction Switch/Measure Unit. It has 28 independent single-pole, double-throw (SPDT) 1A relays and 4 single-pole, single-throw (Form A) 5A relays. This module is used to cycle power to products under test, control indicator and status lights, and to actuate external power relays and solenoids. The Form C channels are 300V, 1A contacts and can handle up to 60W, and the Form A channels are 30VDC/250VAC, 5A contacts and can handle up to 150W. Standard 50-pin Dsub connectors allow for use with standard cables, terminal blocks, or mass interconnect solutions.
-
product
PXI Low-Density General Purpose Switch Modules
These PXI low-density general purpose switch modules provide cost-effective solutions for applications where a high number of relays is not required. All of these modules use a 96 pin male connector that is supported by our comprehensive range of cable and connector accessories, ensuring they can be quickly integrated into your test system with minimum effort.
-
product
General Purpose PXI Relay Switch Modules
PXI relay switch modules offer reliable switching in a variety of configurations. They consist of multiple independent single-pole single-throw (SPST), single-pole double throw (SPDT), double-pole single-throw (DPST) and double-pole double-throw (DPDT) relays. Our PXI relay switch modules come in a variety of relay types including reed relays, electromechanical relays (EMR) and solid state relays—offering you the optimum switching performance for your application.
-
product
PXI High-Density General Purpose Switch Modules
Our PXI high-density general purpose switches provide an ideal solution for applications requiring dense arrays of uncommitted relays.All reed relay modules use high-quality sputtered ruthenium relays that exhibit excellent contact performance under low and medium level switching conditions. Do you have a general purpose application that requires high power handling? We also have electro-mechanical modules that are ideal for just these situations.
-
product
PXI Medium Power General Purpose Switch Modules
Pickering's PXI medium power general purpose switch modules offer higher current ratings in a single 3U slot. The relay solutions have been carefully chosen to ensure a long service life. All the connectors used are fully supported by our cable and connector accessories to simplify system integration.
-
product
PXI High Power General Purpose Switch Modules
Pickering's PXI high power general purpose switch modules provide a range of high current handling relays suited for high power applications. Lower current versions require one 3U PXI slot, the highest current versions occupy two slots. These modules can be used to switch heavy AC or DC loads and the highest current versions are particularly suitable for automotive test. We also have high power switches available in multiplexer and matrix configurations.
-
product
Keysight 20-Channel 5A Form A Switch for 34980A
34938A
The Keysight 34938A is a high power general-purpose switch module for the 34980A Multifunction Switch/Measure Unit. It has 20 independent single-pole, single-throw (SPST) 5A relays. This module is used to cycle power to products under test, control indicator and status lights, and to actuate external power relays and solenoids. Its 30VDC/250VAC, 5A contacts can handle up to 150W on a single channel, enough for many power line switching applications. Standard 50-pin Dsub connectors allow for use with standard cables, terminal blocks, or mass interconnect solutions.
-
product
PXI SPST Power Relay: 20-ch, 5A, 300W
M9135A
The M9135A is a general purpose switch with 20 independent, single-pole, single-throw (Form A) switches in a single PXI module. This module is ideal for switching heavy loads or power supplies including voltages mains or DC current. The heavy-duty armature relays are rated for up to 5A and 300W, enough for inductive or capacitive loads. Choose from the heavy-duty power connector or an unterminated power cable.
-
product
PXI SPST Switch: 50-ch, 100Vrms/1A, Reed Relays
M9132A
The M9132A is a high-density, general purpose switch with50 independent, single-pole, single-throw (Form A) switches in a single PXI module. This module can be used to cycle power to products under test, control indicator and status lights or actuate external power relays and solenoids. The high-speed, long-life reed relays can handle 100Vrms and 1A, with up to 25W power. Choose from the durable connector block or standard cable connections.
-
product
PXI SPST Switch: 100-ch, 100Vrms/1A, Reed Relays
M9133A
The M9133A is a high-density, general purpose switch with 100 independent, single-pole, single-throw (Form A) switches in a single PXI module. This module can be used to cycle power to products under test, control indicator and status lights or actuate external power relays and solenoids. The high-speed, long-life reed relays can handle 100Vrms and 1A, with up to 25W power. Choose from the durable connector block or the standard cable connections.
-
product
PXI SPDT Switch: 64-ch, 100 Vrms / 1A, Reed Relays
M9131A
The M9131A is a high-density, general purpose switch with 64 independent, single-pole, double-throw (Form C) switches in a single PXI module. This module can be used to cycle power to products under test, control indicator and status lights, or actuate external power relays and solenoids. The high-speed, long-life reed relays can handle 100 Vrms and 1 A, with up to 3 W maximum power. Choose from the durable connector block or standard cable connections.
-
product
PXI SPDT Switch: 26-ch, 2A, Armature Relay
M9130A
The M9130A is a general purpose switch with 26 independent, single-pole, double-throw (Form C) switches in a single PXI module. This module can be used to cycle power to products under test, control indicator and status lights or actuate external power relays and solenoids. The armature relays can handle up to 60W power. When needed, these relays can handle up to 6A pulsed carry current. Choose from the durable connector block or standard cable connections.
-
product
General Purpose Switching PXI Card
GX6125
The GX6125 is 3U high density switching card with 25 SPDT Form C relays with a switching power rating of 60 W. The GX6125 is suitable for all test applications requiring general purpose, low level switching.
-
product
PXI Solid State Switch Module, 3xSPST, 10 A
40-182A-012
The 40-182A-012 has 3 off high current SPST switches in one PXI slot and is part of our range of high power solid state switching solutions. Each SPST switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each SPST switch can support 10A of continuous current and switch up to 200V signals. The switch can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
product
PXI Solid-State Switch Module, 3xSPST, 1.5 A, 400 V
40-185A-002
The 40-185A-002 has 3-off high current SPST switches in one PXI slot and is part of our range of high power solid state switching solutions.. Each SPST switch uses a fully isolated solid-state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation.
-
product
High Density Switching PXI Card
GX6338
The GX6338 is a low cost 6U switching card with 114 individual low level SPST Form A relays capable of switching 0.5 A at 200 VDC. The GX6338 is ideal for applications requiring high density switching.
-
product
PXI 4 x Changeover Switch 2.5GHz, 50 SMB
40-710-514
This RF switching card has a bank of four individual high performance RF changeover switches (50 or 75 Ohm, Bi-directional) with very low insertion loss, suitable for handling signals up to 2.5GHz. Applications include aerial switching, routing high frequency signals into oscilloscopes and analyzers.
-
product
PXI/PXIe Microwave Transfer Switch, Single, 50GHz, 50Ω, SMA-2.4
40-782B-551
The 40-782B-551 (PXI) and 42-782B-551 (PXIe) single transfer switches are part of our range of PXI microwave switching modules. They have a characteristic impedance of 50Ω and a maximum operating frequency of 50GHz. Connections are made via front panel mounted high quality SMA-2.4 coaxial connectors.
-
product
PXI/PXIe Microwave Transfer Switch, Single, 40GHz, 50Ω, SMA-2.9
40-782B-541
The 40-782B-541 (PXI) and 42-782B-541 (PXIe) single transfer switches are part of our range of PXI microwave switching modules. They have a characteristic impedance of 50Ω and a maximum operating frequency of 40GHz. Connections are made via front panel mounted high quality SMA-2.9 coaxial connectors.
-
product
PXI/PXIe Microwave Transfer Switch, Single, 26.5GHz, 50Ω, SMA
40-782B-531
The 40-782B-531 (PXI) and 42-782B-531 (PXIe) single transfer switches are part of our range of PXI microwave switching modules. They have a characteristic impedance of 50Ω and a maximum operating frequency of 26.5GHz. Connections are made via front panel mounted high quality SMA coaxial connectors.
-
product
PXI/PXIe Microwave Transfer Switch, Single, 18GHz, 50Ω, SMA
40-782B-521
The 40-782B-521 (PXI) and 42-782B-521 (PXIe) single transfer switches are part of our range of PXI microwave switching modules. They have a characteristic impedance of 50Ω and a maximum operating frequency of 18GHz. Connections are made via front panel mounted high quality SMA coaxial connectors.
-
product
PXI/PXIe RF Switch, Octal SPDT, Terminated, 8GHz, 50Ω, SMA
40-880B-004
The 40-880B-004 (PXI) and 42-880B-004 are octal SPDT 50Ω RF switches with 8GHz bandwidth. The 40/42-880B range have automatic termination of unused signals and are available as a dual switch in a 1-slot, a quad switch in 2-slots or hex and octal switches in 3-slots.
-
product
PXI/PXIe RF Switch, Quad SPDT, Terminated, 8GHz, 50Ω, SMA
40-880B-002
The 40-880B-002 (PXI) and 42-880B-002 (PXIe) are quad SPDT 50Ω RF switches with 8GHz bandwidth. The 40/42-880B range has automatic termination of unused signals and are available as a dual switch in 1 slot, a quad switch in two slots or hex and octal switches in three slots.
-
product
PXI/PXIe RF Switch, Dual SPDT, Terminated, 8GHz, 50Ω, SMA
40-880B-001
The 40-880B-001 (PXI) and 42-880B-001 (PXIe) are dual SPDT 50Ω RF switches with 8GHz bandwidth. The 40/42-880B range has automatic termination of unused signals and are available as a dual switch in 1 slot, a quad switch in a two slots or hex and octal switches in three slots.
-
product
PXI/PXIe MEMS Optical Switch, Triple Insert/Bypass, Single-Mode
40-860A-332-HI
The 40/42-860A-332-HI is a PXI/PXIe triple insert/bypass switch with MU connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
PXI/PXIe MEMS Optical Switch, Triple Insert/Bypass
40-860A-432
The 40/42-860A-432 is a PXI/PXIe triple insert/bypass switch with LC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
product
PXI/PXIe MEMS Optical Switch, Triple Insert/Bypass
40-860A-332
The 40/42-860A-332 is a PXI/PXIe triple insert/bypass switch with MU connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
product
PXI 4 x Changeover Switch 1GHz, 75 SMB
40-710-754
Model 40-710 RF switching card has a bank of 4 individual high performance RF changeover switches (50 or 75 Ohm, Bi-directional) with very low insertion loss, suitable for handling signals up to 2.5GHz. Applications include aerial switching, routing high frequency signals into oscilloscopes and analysers.Available with a choice of connectors: SMA, SMB and Siemens 1.0/2.3 versions. BNC versions are also available with reduced bandwidth and 2 PXI slot occupancy.
-
product
PXI 4 x Changeover Switch 2.5GHz, 50 SMA
40-710-524
Model 40-710 RF switching card has a bank of 4 individual high performance RF changeover switches (50 or 75 Ohm, Bi-directional) with very low insertion loss, suitable for handling signals up to 2.5GHz. Applications include aerial switching, routing high frequency signals into oscilloscopes and analysers. Available with a choice of connectors: SMA, SMB and Siemens 1.0/2.3 versions. BNC versions are also available with reduced bandwidth and 2 PXI slot occupancy.