Showing results: 166 - 180 of 477 items found.
-
629 -
Electronic Specialties Inc.
*Alligator clips screw off / on for more secure connection *Test leads 48” length *1000 Volts max - CATIII *Maximum 10 Amps
-
Mountz Inc.
Mountz EZ-Glider torque arms are designed to improve safety, production and quality control during assembly. Power tools generally produce unwanted torque reaction that transfers to an operator’s hand. The daily repetitive process of fastening screw after screw with a power tool exposes operators to the risk of repetitive stress injuries. Torque arms prevent both scenarios by absorbing the torque reaction while simplifying the motions available to the tool operator.
-
ENVIROMUX-GBS -
Network Technologies Inc
Acoustically detects the cracking of glass. Adjustable sensitivity. Includes mounting hardware. Connect to RJ45 or digital input sensor ports. Supports CAT5/5e/6 UTP or STP cables. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Maximum cable length: 1,000 ft (305 m). Powered by ENVIROMUX-2D/5D/16D.
-
4B Components Ltd.
Screw in positive mount installationGrease zerk for bearing lubrication1/2” NPT conduit entry (steel body)NTC version - continuous temperaturePTC version - trip points from 122°F to 194°FPT100 version - platinum RTDClass 2 Div 1, Div 2 Approved
-
Heidenhain Corp.
Linear encoders measure the position of linear axes without intervening mechanical elements. This eliminates a series of potential error sources such as backlash, pitch error, or heating of the recirculating ball screw. Wherever rigorous position accuracy and high machining speeds are needed, linear encoders are essential.
-
776990-01 -
NI
100-Pin Female SCSI to 100-Pin Female Screw Terminal, Desktop Mount Terminal Block - The SCB-100 is a shielded I/O connector block for interfacing I/O signals to NI data acquisition devices with 100-pin connectors. Combined with the shielded cables, the SCB-100 provides rugged low-noise signal termination.
-
ThermoVault -
MadgeTech, Inc
Oven Temperature Profiling kit. Comes with TC101A Thermocouple based Temperature Data Logger with screw terminal, Thermally insulated enclosure, and Type K thermocouple probe.
-
IQ Series -
Ametek Land
IQ series thermometers feature an all metal design with integrated water cooling, air purge and screw terminal connections to facilitate simple and cost effective operation.
-
Virginia Panel Corporation
modules mount from the rear of the iCon receiver and ITA and allow installation and removal of pre-wired cable blocks. The modules also have captive Phillips head screws.
-
Metra Mess- und Frequenztechnik in Radebeul e.K.
Triaxial accelerometers are intended for simultaneous measurement of vibration in 3 perpendicular axis. All models have a central drilling for easy screw attachment and convenient axis alignment.
-
-
Traceable Products
Meter reads from 0 to 1,999 foot-candles (resolution 0.1 to 1). Bright 1/2-inch-high digits make it an easy to read pocket light meter. The simplicity of the two-button operation eliminates the need to refer to directions. Functions are on/off, and range. The meter can be zeroed with the simple turn of an adjustment screw
-
cBP-6418U -
ADLINK Technology Inc.
*1 Segment: 1 system + 7 peripheral slots*cPCI BUS: up to 64-bit/66MHz*Power connectors: ATX connector x 1 DC Screw terminals
-
779353-01 -
NI
37-Pin, Female D-SUB to 40-Pin, Female Screw Terminal, Desktop Mount Terminal Block - The CB-37F-LP is an unshielded terminal block that provides access to DAQ devices with 37-pin connectors. The 37-pin, D-SUB connector makes this connector block ideal for direct mounting on the … DAQ device or connecting through a cable.
-
199SM / 198EM Magnet Wheels -
Electro-Sensors, Inc.
Magnet wheels work with Electro-Sensors Hall Effect shaft speed sensors providing 120 alternating magnetic poles around the circumference of the 3.75" diameter. The 199SM models mount around shafts up to 3" in diameter and are secured with set screws (provided). The 198EM mounts on the end of a shaft with a 10-32 UNF screw (provided - requires center drilling and tapping the shaft).• Use with 906, 906B, 1101 and other Hall Effect, non-metallic-end-capped shaft speed sensors (consult factory)