Showing results: 301 - 315 of 360 items found.
-
Washington Laboratories LTD.
Medical devices are subject to many regulatory standards from general requirements for basic safety and essential performance (60601-1) with inclusion of several collateral standards dealing with operational characteristics (e.g. 60601-1-2 for EMC; 60601-1-11 for home medical, etc.) and vertical standards dealing with specific aspects of the device (particular standards often referred to as -2 standards). Test and evaluation of the applicable requirements stem from Edition 3 (currently in effect for most regions) with a risk based review to assess applicability of the standard and to identify areas not covered by the standards.
-
F-Squared Laboratories
F2 Labs can provide you with Federal Communications Commission (FCC) Certification in our EMC Testing Lab, Supplier’s Declaration of Conformity (SDoC), formerly Verification and Declaration of Conformity, testing. Manufacturers who sell electrical and/or digital products in the United States must have their products tested by an accredited lab certified by the FCC. F2 Labs is accredited by the FCC as a Conformity Assessment Body (CAB). We partner with a Telecommunication Certification Body (TCB) in order to provide our clients with FCC Part 15 certification and compliance testing & approvals.
-
Silent Solutions LLC
SILENT offers pre-compliance testing for products with planned distribution to commercial and industrial markets in the US and overseas. This includes testing to ensure that emissions, immunity, and circuit-to-circuit interference problems are discovered early and immediately brought under control. We use the most advanced EMC and RF test & measurement equipment and diagnostic software available from leading suppliers.
-
Com-Power Corporation
Transient limiter LIT-153A and LIT-930A protects a spectrum analyzer input from high-level transients from the line impedance stabilization networks during EMC conducted emissions testing. It has a combined frequency range of 9 kHz to 30 MHz. The built in high pass filter helps reduce 50/60 Hz line feed through. (see application notes)
-
Hilo Test
The ESD Simulators ESD suitable for performing EMC tests of systems and equipment according to the standards IEC / EN 61000-4-2 and ISO / TR 10605. It can far beyond the standard boundaries higher test levels are adjusted. Depending on the device under test and the test setup are two test method shall be: Air discharge (AIR) and contact discharge (CON).
-
CryoARM -
JEOL Ltd.
JEOL announces the latest member in its family of high-end transmission electron microscopes, the CryoARM. This highly automated TEM is designed for unattended operation and high throughput imaging of cryo-EM specimens. The CryoARM was initially introduced to a select audience at the 2016 Gordon Research Conference in Hong Kong, M&M 2016 in Columbus, OH and EMC 2016 in Lyon, France. The CryoARM is a dedicated cryo-TEM, based on the highly successful JEOL ARM (Atomic Resolution Microscope) series, an ultrahigh performance, highly stable platform considered to be the "best-in-class" TEMs. The development of the CryoARM was accomplished in collaboration with leading Life Science researchers.
-
Communications & Power Industries
CPI SMP Division provides a complete line of high-powered continuous wave (CW) and pulsed instrumentation amplifiers for EMC testing, available in octave and multi-octave bandwidths from 1.0 GHz to 95.0 GHz and power levels exceeding 2.0 kW to meet the new military and automotive standards. CPI is the only supplier that manufactures both the traveling wave tube (TWT) and the TWT amplifier.
-
Rhein Tech Laboratories, Inc.
Rhein Tech Laboratories, Inc. (RTL) is a full-service design and compliance engineering test laboratory. We have grown with the industry from general purpose EMC testing into other areas of testing such as Radio (RF testing), Military and Aviation, Industrial, Scientific and Medical, Automotive, Electrical Safety, Shielding Effectiveness, Site Surveys and Radar Cross Section & High Range Resolution measurements.
-
EA-300 -
Laplace Instruments Ltd.
The EA-300 is a stand alone unit with internal firmware and a large colour display. It connects to the outputs from a standard LISN and feeds the results to any standard EMC analyser or receiver. The EA-300 prompts the user through the steps necessary to fully characterise the emissions from the EUT, then will output via the screen the recommended filter component values that would reduce these emissions to acceptable levels.
-
783106-01 -
NI
400 Vrms L-N, 800 Vrms L-L, 50 kS/s/ch, 24-Bit, 3-Phase C Series Voltage Input Module - The NI‑9244 performs single-ended analog input. The wide measurement range makes it ideal for high-voltage measurement applications such as phasor measurements, power metering, power quality monitoring, industrial machinery, and motor test. You can also perform transient and harmonic analysis with high-speed simultaneous sampling. The NI‑9244 offers three channels, so you can connect single‑ or three‑phase measurement configurations such as WYE and delta. You can incorporate the NI‑9244 into systems to meet standards such as IEC 61010‑1, C37.90 and C37.60, IEC 60255‑22‑(1:7), IEC 60255‑1, C37.188 Class M and P, EMC section of IEC 60870, EMC sections of IEC 61850, IEC 61000‑4‑30 Class S, and IEC 61000‑4‑7.
-
Elektra -
Rohde & Schwarz GmbH & Co. KG
The R&S®ELEKTRA test software controls complete EMC systems and automates measurements of equipment under test (EUT) being certified for emissions (EMI) and immunity (EMS). R&S®ELEKTRA simplifies configuration of test systems and test descriptions in accordance with common standards. It speeds up test execution and paves the way to quickly generating a comprehensive test report.
-
GT-1000B -
Spanawave Corporation
The Spanawave GT-1000B Microwave Power Amplifier offers linear high-power amplification across multi-octave bands. It is ideal for testing in EMC, wireless communications applications and Defense EW systems. For EMI/EMC and standards laboratories, the GT-1000B with 100 MHz to 20 GHz frequency range allows broadband testing without band switching or swapping narrow band amplifiers resulting in faster and more accurate testing.
-
Insight Product Company
Travelling wave tubes remains a valuable type of amplifier for high output power in the microwave range. Its main advantages are of high output power, big bandwidth-duration and reliability. Insight Product Co. offers TWT packaged tubes providing output power from tens to several hundred watt in a continuous mode and to 1.5-2.0 kw in a pulse mode, and frequency bandwidth of 1.5 octaves. TWT applications include satelite communications (transponders) both on land and on satelite installations, radio relay communication lines, electromagnetic compatability (EMC) testing industry for immunity testing of electronic devices, and radars (maritime, weather, airplanes, land).
-
PC-114 -
Com-Power Corporation
Perform Radiated & Conducted EMI pre-compliance testing at your facility up to 1 GHz. Com-Power PC-114 EMI emissions test system is a ideal solution performing pre-compliance EMC testing from 9 kHz - 1 GHz.. It has essential equipment needed for radiated and conducted EMI emissions measurements. The system includes a spectrum analyzer, antennas, near field probes, a preamplifier, LISN and a non conductive antenna tripod. Pre-compliance testing in EMC is a commonly used term not easy to define. In general, it implies testing done prior to formal testing for legal compliance. Formal legal compliance is performed at a facility designed and equipped with test instrumentation that is fully compliant with the applicable EMC standards. Such facility and instrumentation is capital intensive and can be expensive even to rent and not easily available. Compliance testing is performed per exacting requirements of the Standards and other reference documents adhering to the test methods and last detail. In addition, the test facility may require to be accredited by an accreditation body such as NVLAP, A2LA. Often it is desirable to know prior to compliance testing at such facility, whether a product is close to compliance and also how close. Pre-compliance testing is specially useful for specifications such as FCC, Part 15, EN 55022 or EN 55011 (CISPR 22 or CISPR11). Pre-compliance testing usually means using the full compliance methods but making a few educated compromises in use of site or equipment to reduce costs and testing time. Here are some benefits of pre-compliance testing.
-
EMC Test Design, LLC
Active broadband isotropic antenna combined with portable USB powered spectrum analyzer. OFA-S/SE antenna has frequency response independent of antenna or electric field orientation. It offers broad dynamic range for the variety of RF regulatory, safety, EMC, wireless and telecommunications applications. Spectrum analyzer SA-S displays the frequencies and field strength of selected signals, allowing all results to be viewed and stored on PC.
