Filter Results By:
Products
Applications
Manufacturers
System Test
Testing conducted on a complete, integrated system to evaluate the system's compliance with its specified requirements .
See Also: Systems, Equipment, Test Systems, System Integrators
-
product
DC Power Module 0 To 5 V, 0 To 10 A, 50 W
N6731B
The Keysight N6731B, a 50 W basic DC power module, provides programmable voltage and current, as well as measurement and protection features at a very economical price. Use this module to power the device under test or ATE system resources, such as fixture control.
-
product
G12x - 18 Module Solution
The G12x Receiver has four removable rubber feet below the platform and also allows for permanent tabletop mounting. Available with 15" or 20" platforms. The G12x accepts ITAs designed for both the G12 and G12x allowing versatility with your test system.
-
product
Combined Map Display Unit & Interface Unit Tester (COMED)
MS 1117
This system is used to test COMED (Combined Map Electronic Display) IFU cards. This ATE checks the LRU Status and card status and identify faulty component in the individual UUT. On fault, this suggests the possible component failure as diagnostic report, for repairing the cards.
-
product
Enclosure, S6, 4"x18"x12", for Discrete Wiring
410112712
This Enclosure gives you the ability to discrete wire to your UUT with secure strain relief provided by the cable clamps located on the back end. The Enclosure is over 2U in height which provides more space for wiring and other test system needs.
-
product
50 Channel Linear Vibration Motor Aging Unit
BK2021
The BK2021 50 Channel Linear Vibration Motor Aging Test System was designed to test your linear vibration motors so you know they are working. Load a jig drawer in the jig assembly unit with 10 DUT's. Close the drawer to start testing and begin loading the next of the 5 drawers. When the machine has finished running up to 4 test sequences that you've programmed in, the drawer opens. On the front, a green light tells you the motor is good, a red light tells you there was a short and if there is no light you know there was an open circuit.
-
product
Cybersecurity Penetration Testing Assessments
Tripwire Professional Services
Organizations do all that they can to protect their critical cyber assets, but they don’t always systematically test their defenses. Penetration tests—otherwise known as pen tests—are a type of ethical hacking used to regularly evaluate the security of a network. Our team of highly-skilled cybersecurity experts utilizes a combination of tactical and strategic approaches to discover and exploit vulnerabilities in your IT systems. Whether we are testing an application or network environment, Tripwire’s pen testing will not only identify vulnerabilities, but it will also demonstrate them through exploitation—definitively determining if unauthorized access or other malicious activity is possible.
-
product
BGAN Network Emulator
BNE
Square Peg Communications Inc.
The Gatehouse BGAN Network Emulator (BNE) is a test tool developed and optimized to work in concert with the Square Peg BPLT to provide end-to-end emulation of the BGAN Network. The combination of the BPLT and BNE provides an on-the-bench emulation of the I4 satellites, the BGAN Radio Access Network (RAN) and the Core Network (CN). It is a very powerful test solution that enables terminal manufacturers, system integrators and application developers to test their applications thoroughly and consistently and to verify that applications are optimized to work under any network condition thereby providing the best possible user experience.
-
product
Carrier Acceptance Test Solutions for Network Operators
The Rohde & Schwarz carrier acceptance test systems provide access to the most important test plans of the world’s major mobile operators.Voice over NR, data throughput, protocol, positioning, RF, RRM and application testing – all relevant test scenarios are available on a common hardware platform.The entire range of 5G NR testing modes are available, covering sub-8 GHz (FR1) and mmWave (FR2) frequencies, and both non-standalone (NSA) and standalone (SA) modes.Contact your Rohde & Schwarz sales representative to learn more about the latest products and features.
-
product
Anite Development Toolset
Benefit from a comprehensive suite of tools that support all phases of wireless terminal development, from pre-silicon protocol module development through to systems integration and verificationGain easy access to parameters at lower layers to re-create tests in the very early stages of chipset and device developmentAccess an extensive LTE/LTE-Advanced technology roadmap including early 5G specificationsRemain in control of test designs through accessing Layer 1 and Layer 2 using Application Programming Interfaces (APIs)Benefit from a high level of flexibility and control in terms of test creation
-
product
Smart Card Testers
CT1000
The CT1000 testers are open and configurable to test any kind of communication protocols used on smart cards, and to be updated for new technologies. The systems can test devices that use common standard protocols (as ISO 18000, EPC Global Gen 2, ISO 14443, ISO 15693, MIFARE™, DESFIRE™, FeliCa™, ISO 11784/85, ICode™, Hitag™, ISO 7816, ISO 7813), and are ready to test also the next generation of cards protocols, such as: USB-Keys, MMC, Micro-SD (with and without CPU inside), M-SIM, HD-SIM, SIM-WAVE, and I2C.
-
product
Impulse Voltage Generator
Hilo-Test manufactures Surge generators for surge voltage and safety tests as well as for testing the insulation withstand voltage, the waveform in accordance with IEC 60060. Especially for EMC tests on photovoltaic systems and surge voltage tests, for example, to relay, capacitors, coils.
-
product
Wide Range High Voltage Programmable DC Power Supply
N3600 Series
Next Generation Instrumental (Shanghai) T&C Tech. Co., Ltd.
N3600 series is developed based on NGI's years of experience in testing for battery fluctuation simulation test, battery charger, high voltage diode, electrolytic capacitor, electromechanical control, ATE test system, etc. It is a high-voltage wide-range programmable DC power supply. According to different test environments in the fields of lab test, system integration test, and mass production line, NGI has made a number of optimization designs based on the international advanced technology. N3600 series is a market leader in similar products in terms of reliability, maintainability and safety.
-
product
Thermo-hygrometer Handheld Temperature And Humidity Meter
HW100
Shenzhen Chuangxin Instruments Co., Ltd.
HW100 temperature humidity meter is a portable temperature humidity test instrument., selecting high performance capacitor type polymer film humidity sensor and semiconductor type temperature sensor. It has features of volume small, weight light, easy carrying, multi-function, and high precision, etc., applies to various fields such as hot comfortable research, indoor air quality assessment, verification of HVAC system run situation in building, heating and refrigeration system overhaul, and detection of the air conditioning system during the production process and so on.
-
product
Battery Cell Simulator
BCS-LABCAR
The ETAS Battery Cell Simulator (BCS-LABCAR) is a Hardware-in-the-Loop system which specifically targets the signal-level test, validation, and calibration of battery management systems (BMSs). The BCS-LABCAR is a high-precision Battery Cell Simulator that emulates the behavior of individual battery cells and packs across a wide range of challenging operating conditions, e.g. cell balancing over-charging, deep discharging, or pulse operation. The system is highly modular and thus scalable to emulate battery packs from a single cell all the way up to 200 cells.
-
product
Fuel Quantity Testers
Fuel capacitance systems are separated into two broad groupings, AC capacitance and DC capacitance. The source of these names derives from the type of signal processed by the fuel system amplifier. Barfield designs a universal tester for each type of system with the proper interface harnesses to access individual aircraft applications. Some of the various test and measurements include:*Insulation - Testing the wiring and probes*Fuel Tank Capacitance Measurement*Individual Probe Capacitance Measurement*Capacitance Simulation - Indicators and amplifiers*Indicators - Bench testing of remote units
-
product
Testing Released Water Vapor
Humiditest™ Complete System
The James Instruments Humitest System allows the concrete practitioner to monitor and ensure that a new structure is dry enough to proceed with the next phase of construction. This is especially critical for concrete structures requiring a coating, carpeting or similar floor or covering treatment. Installing such treatments before the concrete is sufficiently dry will typically cause expensive failures in the covering treatment. The only accurate way to ensure that the concrete is sufficiently dry enough to safely avoid expensive re-work is via a bore hole humidity test system, such as the Humitest System
-
product
VPX 3U Universal RTM
1940000377-0000R
The Universal 3U VPX RTM Breakout Board can allow a test engineer to access I/O signals on custom built VPX boards. The breakout board is designed for the utility, power, single ended or low speed differential signals during setup and testing of a new system. During system integration, it often is desirable to access certain utility signals such as VS1, VS2 or VS3, auxiliary voltages other signals such as Geographic address or the system management bus which are all available from the rear side of the backplane.
-
product
Kjeldahl Analyzer
LD-LKA-A10
Kjeldahl AnalyzerLD-LKA-A10is a complete microcomputer controlled user-friendly automatic device integrating distillation and titration functions. It is compatible with 42 mm digestion tubes and has features such as automatic waste discharge and cleaning of digestion tubes and titration cups, control steam flow and real time detection of distillation temperature. Along with High-accuracy Charging Pump and Titration system, it is also equipped with large LCD touch screen panel, faster ARM system and multiple fluid level detection system to ensure smooth test process.
-
product
Fiber Optic Test Kit
KI-TK081
Small single mode fiber optic test kit for low to medium test volume on SM systems. A fiber optic power meter and light source in a padded zip case.
-
product
Electronic Equipment Testing System
The task set forth the need to create a special universal software core, the main tasks of which are the provision of measurement and control processes, as well as the interaction of software components intended for collection, visualization, mathematical processing and documenting of data. For each stand, specific program modules were additionally developed according to test methods specific products. The overall modular architecture of the system makes it easy to supplement and correct test algorithms.
-
product
Turns Ratio Meter 3 Phase
TR-MARK III 250V
The TR-MARK III 250V is the successor of the famous TR-MARK III. Besides an extended test voltage up to 250V, it offers new features and increased accuracy to make it a perfect system. A color LCD with back lighting and touch screen increases handling and user comfort. Two USB interfaces make it easy to store measurements on external storage devices and transfer easily to a personal computer or download nameplate data of transformer to test.
-
product
Transceiver Driver
S-112
Transceiver Driver slot module of FOTS system is an efficient module for the characterization of SFP type transceiver and the test of optical line or components. This module is a kind of Small Form Factor Pluggable(SFP) host board that can be used to test SFP transceiver modules to define the modules’ performance. The transceiver driver slot has two SFP cage and 20-pin SFP connector sets to mount and control two SFP transceivers simultaneously.
-
product
Air Data Calibrator
ADC-2575
TestVonics ADC-2575 Air Data Calibrator is a high accuracy pitot static calibrator. The calibrator is capable of controlling and measuring Altitude and Airspeed pressures with the highest degree of accuracy. The control and measurement range of the test system can meets or exceed requirements for both commercial and military applications. The ADC-2575 is a derivative of the ADC-2550 Series. It features a touchscreen interface, a mid range 23PSIA sensor. It is ideally suited for Automated Test Equipment (ATE) applications.
-
product
Reference Thermapen®
Until now you would have spent hundreds more to get this level of accuracy in a NIST-Traceable standards thermometer. Our Reference Thermapen takes lab accuracy into the field. Each unit is factory calibrated at 5 test points and includes a UKAS accredited calibration certificate with test data. A true "system calibration" is performed matching its Platinum RTD sensor and the built-in electronics so all errors are included in the spec.
-
product
Stimulus Induced Fault Testing
SIFT
SIFT allows for the analysis of numerous stimuli to identify speed, fault, and parametric differences in silicon. The heart of the SIFT technique revolves around intentionally disturbing devices with external stimuli and comparing the test criteria to reference parts or timing/voltage sensitivities. Synchronous interfacing is possible to any tester without any wiring or program changes. The system can be based on either a motorized probe station or portable microscope stand for test head applications.
-
product
NI's Electrical Functional Test Solution
PXI instrumentation ensures complete and accurate test coverage with a modular architecture mounted in ultra-reliable PXI chassis.TestStand and LabVIEW software provide rapid development of complex test steps and sequences. PXI systems conserve floorspace because of their small, light form factor. Order them preassembled and installed using NI ATE Core Configurations.SystemLink™ software deploys updates and democratizes data insights to optimize operational efficiency.
-
product
PSE Conformance Test Suites
4-Pair 802.3bt PSE's
*Robust 4-Pair 802.3bt (Type-3,4) PSE Conformance Testing*Fully Automated Port Sequencing and Statistics - Test up to 24 ports with the PSA-3000*Catch Both Repeatable and Intermittent Specification Compliance Issues*Greater than 92% 802.3bt PICS Coverage from 24 Fully Automated Tests*Pop-Up Excel Reports Covering 1 to 24 Ports*Widely Used by PSE System and Silicon Manufacturers World Wide
-
product
Automotive High Low Temperature Environmental Test Chamber
Dongguan City Simplewell Technology Co. Ltd.
*Windscreen deforsting and demising tests for M1 category vehicles;*Windscreen wiper and washer property tests*Cold start tests for M1 category vehicles and engineers*Air conditioning system tests for M1 category vehicles*Property tests for small-size refrigerated trucks*Environmental tests for M1 category vehicles,small-size trucks,special purpose motor vehicles,motorcycles,engineers and components.
-
product
High Voltage Insulation Tester Module
DP-cPCI-5586
DP-cPCI-5586 is a High Voltage Insulation Tester Module. This module facilitates single-board voltage source/measurement features with high voltage output and a nanometer. Occupying a single slot in standard cPCI rack, this module can be used for multiple point cable harness test systems with limited rack space. Applications of this board include automatic test equipment, checkout systems, force voltage measure current, and insulation test.
-
product
PXI Very High Density Versatile 2-Pole MUX
40-613-002
The 40-613 Very High Density Versatile 2-pole Multiplexer module features a wide range of software selectable switching configurations. It is especially useful where a number of high density multiplexers are required with the option of easily altering the channel count as a test system evolves.