Showing results: 1336 - 1350 of 2443 items found.
-
PDMT25 -
Pyle Audio Inc.
4000 Display CountPeak Capture ModeData HoldMax/Min Recording ModeVoltage DC: Max Range 1000 V, Accuracy +/- 0.5%Voltage AC: Max Range 1000 V, Accuracy +/- 0.8%Current DC: Max Range 10 A, Accuracy +/- 1.2%Current AC: Max Range 10 A, Accuracy +/- 1.8%Resitance: Max Range 40 M, Accuracy +/- 0.8%Duty Cycle: Max Range 99.9%, Accuracy +/- 1.2%Temperature: Max Range 760 C / 1400 F, Accuracy +/- 3.0%Frequency: Max Range 10 MHz, Accuracy: +/- 1.5%Capacitance: Max Range 40 mF, Accuracy +/- 1.5%Diode Check
-
CRD-005 and CRD-020 -
Powertek LLC
CRD-020 Programmable ac current set-point relay setting for threshold levels, over and under-currentoperationbullet CRD-005 Programmable dc voltage and mA set-point relay setting for threshold levels, over and under-voltage operationbullet CRD-005 internal DIP-switches allow for either 0-1mAdc or 0-10Vdc operation, and may be set for under-alarm or over-alarm relay operationbullet CRD-020 internal DIP-switch allow configuration of the ac current range to either 0-5A, 0-10A, 0-15A or 0-20A and the relay mode for under-current or over-current operationbullet Lid mounted two digit numerical push button switch calibrated as percent of full scale with a threshold range of 1-99%bullet Red LED lamp lights to indicate when the threshold level has been tripped
-
Series HSM -
Kepco, Inc.
The Kepco HSM series comprises a group of ten models, seven 1000 watt power supplies with outputs from 3.3 volts to 125 volts and three 1500 watt power supplies with outputs from 24 to 125 volts. All models feature current sharing for parallel operation and redundancy applications. Kepco¹s 1000W HSM have a wide-range input (90-277V a-c). The 1500W models operate 180-277V a-c. Both incorporate power factor correction to meet EN 60555-2 and EN 61000-3-2. These modern power supplies operate at 100KHz using current mode control to provide rapid response to source and load changes and tight stabilization.
-
409B -
Novatech Instruments , Inc.
The 409B generates four independent, phase synchronous sine wave output signals and is programmable in 0.1 Hz steps from 0.1 Hz to 171 MHz. Programming is via an RS232 serial interface. Phase is 14-bit programmable and amplitude is 10-bit programmable. Internal memory can store a sequence of settings. The -AC option is available to enable users to step through settings using an external trigger. It is accurate to 1.5 ppm using the on board TCXO timebase or you can use an external timebase, There is also a /R option that provides a way to lock to and track an external 10MHz frequency input. A line powered AC adapter and SOF8_409 windows software on a CD are included.
-
PFM1010 -
Applied Test Resources
The PFM1010 Module is a precision instrument capable of measuring all common DC parameters in a power MosFet as well as many of the AC parameters. This module uses some very innovative techniques to make it possible to measure parameters like Rdson down into the sub-million-ohm range.
-
HGM09 -
MAGSYS Magnet Systeme GmbH
Data storage on a personal computer via keystroke. The HGM09s is easy to use and has a good price/performance ratio. The handheld gaussmeter HGM09s is used to measure magnetic DC and AC fields. The measurands are flux density in Tesla or Gauss and the field strength in Amps per meter.
-
CP-3308R -
PINTEK Electronics
*100:1 scope probe *300MHz Bandwidth *Read out Function *Division Ratio x 100 *100MΩ Fix Input Impedance *1500V DC Working Voltage (CAT Ⅱ) *2000V AC peak to peak MAX. (CAT Ⅰ) *CE Approved.
-
AMIC-5005 -
Amperis sl
Insulation resistance measurement - 15TΩ: * 50 - 1000 V, in 10 V steps, * 1000 - 5000 V, in 25 V steps ; Memory of 999 results and transmission to PC ; Measurement of AC and DC voltage and capacity ; Measurement of leakage current ;Function with digital filter
-
AMIC-10 -
Amperis sl
The AMIC-10 digital insulation resistance meter is used for direct measurements of the insulation resistance of electrical equipment working with voltage up to 1 kV. In addition, this meter makes it possible to measure compensation and protective connections, low-voltage resistance measurements and DC and AC voltage measurements.
-
Shanghai MCP Corp
Taut-Band movement.26 measuring range with Min. 1mV and 100uA(MS506-A) both in AC and DC.Zero at midpoint function (voltage meter,current meter and galvanometer 3 in 1).Overload warning LED indicator.Input impedance:100kΩ at all voltage ranges.Battery test function
-
1287A -
Ametek Scientific Instruments
The Solartron Analytical 1287A potentiostat and galvanostat is a high accuracy, wide bandwidth instrument which offers a range of DC test capabilities. The 1287A can be coupled with a frequency response analyzer, such as the Solartron Analytical 1260A or 1255B, and ZPLOT software for AC tests such as Electrochemical Impedance Spectroscopy.
-
SGA -
Interface Inc.
Versatile signal conditioner featuring user selectable outputs of +/-10V, +/-5V, 0-10V, 0-5V, 0-20mA and 4-20ma. DC or AC powered with switch selectable filters from 1 to 5kHz and a sealed ABS enclosure. Supports shunt calibration and a wide range of gain settings.
-
PU 182.1 -
Metra Blansko a.s.
The instrument is primarily intended for measurement of the insulation resistance of electrical objects and equipment according to the CSN 331610 standard (for electrical appliances) with nominal voltage 100 V, 250 V and 500 V. It also allows to measure AC and DC voltage up to 550 V,
-
Fluke T6-600 -
Iconic Engineering Limited
Fluke T6-600 Electrical Tester field sense technology for ac voltage, current, and frequency measurement without making electrical contact to live voltage. The most important things about the Fluke T6-600 electrical tester that always provide an accurate measurement in any environment.
-
SUMMIT192/194 -
Summit
50000 Counts Triple Display. 51 Segments Analog Bar Graph. Backlight & RS-232 Interface. True-RMS (50kHz). Capacitance (Max 20mF) & Inductance. (Max 300mH) ? Conductance & AC + DC. 192(CATIII 600V), 194(CATIV 600V)