Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Ltd.
product
PXI Voltage Amplifier SMB Type Connector
41-650-002
A 5 channel voltage amplifier ideal for increasing the output voltage from other PXI modules, enabling users to easily generate the signal voltages commonly required in applications such as automotive test.
-
product
Isolation Amplifier
Mornsun Guangzhou Science & Technology
An isolation amplifier is an amplifier that provides isolation between the input and output of the circuits, including isolation between their associated power supplies. MORNSUN offers different types of analog isolation amplifiers, such as acquisition type signal conditioning modules, output isolation signal conditioning modules, two-wire loop power supply signal conditioning modules and signal isolators, etc. These analog isolation amplifiers feature excellent temperature drift characteristics of less than 50PPM/℃ across the entire operating temperature range of -40 ℃ to +85 ℃ and achieve isolation transmission, signal conversion (programmable for some models), HART communication, signal amplification, port protection and other functions. SIP, DIP, SMD and DIN Rail packages are optional.
-
product
Isolation Amplifier
Isolation amplifiers are indispensable components for signal conditioning. There are several reasons that make galvanic potential isolation necessary. Examples for this are personal protection, on the one hand, as required in medical engineering to ensure contact of persons with life-threatening voltages. On the other hand, different safety aspects, such as protection of IT systems may require the use of an isolation amplifiers. If ground loops need to be separated or if a small differential voltage with a high common-mode level must be determined, the isolation amplifier is the device of your choice.
-
product
Isolation Amplifiers
Isolation Amplifiers provide power supply designers with a higher performing, single chip alternative to isolation techniques based on optocouplers and shunt regulators. Analog Devices ADuM3190 and ADuM4190 isolated error amplifiers have a 400 kHz bandwidth, with 0.5% typical initial accuracy at 25°C and 1% total accuracy over the extended temperature range of –40˚C to +125˚C. This provides manufacturers of ac-to-dc and dc-to-dc power supplies with a significant upgrade in speed and operating temperature range, as well as a 5× improvement in transient response.
-
product
Isolation Amplifiers
Knick Elektronische Messgeräte GmbH & Co. KG.
Unipolar and bipolar DC input signals 20 mV to 200 V and 0.1 mA to 100 mA calibrated range selection. Working voltage up to 1000 V AC / DC.
-
product
Galvanic Isolation Amplifier
X005 Series
The X005 Galvanic Isolation Amplifier provides a regulated and resistively limited +5V dc power supply required by the sensors, it can be connected in three or five wire modes. Used in five wire mode positive and negative sense inputs enable the X005 to dynamically adjust the sensor supply thus ensuring the correct voltage across the sensor. Connected in this way the X005 can compensate for 15 conductor resistance. The sense terminals are linked internally so the end user can use the X005 in three wire or five wire mode without the need to fit or remove external links.
-
product
Dining Isolation Amplifier
Knick Elektronische Messgeräte GmbH & Co. KG.
To feed and Isolation of 2-wire transmitters / sensors or SMART transmitters with HART transmission. Working voltage up to 2500 V AC / DC. Available for hazardous and non-hazardous area.
-
product
High-Voltage Isolation Amplifier
Knick Elektronische Messgeräte GmbH & Co. KG.
Measurement of DC or AC voltages up to () 3600 V and of large DC currents to about () 20 kA with shunt resistor or directly in the device to () 5A DC and AC. Variants with calibrated range selection.
-
product
Shunt Isolation Amplifier
Knick Elektronische Messgeräte GmbH & Co. KG.
Especially to accurately measure large DC currents via shunt resistors, ie for making isolated detection of mV voltage on shunts. Variants with calibrated range selection. Working voltage up to 3600 V AC / DC.
-
product
Isolation Amplifier Analog Output
This coupler is an optically coupled isolation amplifier that uses an IC with a high-accuracy sigma-delta A/D converter and a GaAIAs light-emitting diode with high-speed response and high luminance efficiency on the input side, and an IC with a high-accuracy D/A converter on the output side. This coupler is designed specifically for high common mode transient immunity (CMTI) and high linearity (nonlinearity) applications, making it ideal for current sensing in motor drives.
-
product
Isolation Amplifier Digital Output
This coupler is an optically coupled isolation amplifier that uses an IC with a high-accuracy sigma-delta A/D converter and a GaAIAs light-emitting diode with high-speed response and high luminance efficiency on the input side, and an IC with a digital signal (MDAT, MCLK) output function on the output side. This coupler is designed specifically for high common mode transient immunity (CMTI) and high linearity (nonlinearity) applications, making it ideal for current sensing in motor drives.
-
product
16-Ch. Isolation Amplifier Signal Conditioning Card
ProDAQ 5828
The ProDAQ 5828 Isolation Amplifier Signal Conditioning Card is designed to isolate and amplify wide bandwidth analog signals. It provides 16 channels with complete galvanic isolation and can be used directly with any of Bustec’s high-performance ProDAQ 3416 16-channel Sigma-Delta ADC Function Cards.
-
product
PXI Voltage Amplifier, +/-33V
41-650-001-S1
A 5 channel voltage amplifier ideal for increasing the output voltage from other PXI modules, enabling users to easily generate the signal voltages commonly required in applications such as automotive test.
-
product
PXI Voltage Amplifier D Type Connector
41-650-001
A 5 channel voltage amplifier ideal for increasing the output voltage from other PXI modules, enabling users to easily generate the signal voltages commonly required in applications such as automotive test.
-
product
PXI Voltage Amplifier 10K Ohm, D Type
41-650-011
A 5 channel voltage amplifier ideal for increasing the output voltage from other PXI modules, enabling users to easily generate the signal voltages commonly required in applications such as automotive test.
-
product
PXI Signal Amplifier
3180
Model 3180 was designed as a general purpose, wide band and high voltage amplifier, however, with specific applications in mind. It offers selectable gain of up to x50, with amplitudes of -90V to +90V and an output current of 150mA.
-
product
PCI Bus Signal Amplifier
3322
Model 3322 is a 3U single-slot, PCI-based power amplifier designed for signal amplification. Offering unmatched signal purity, Model 3322 amplifies signals from dc to over 20 MHz. The unit has a fixed gain of x10, however, the same amplifier is available with custom gain, with no signal purity or performance degradation.
-
product
PXI Bus Signal Amplifier
3222
Model 3222 is a 3U single-slot, PXI-based power amplifier designed for signal amplification. Offering unmatched signal purity, Model 3222 amplifies signals from dc to over 20 MHz. The unit has a fixed gain of x10, however, the same amplifier is available with custom gain, with no signal purity or performance degradation.
-
product
Wideband Amplifier PXI Card
GX1222
The GX1222 is a 3U single-slot, PXI-based wideband power amplifier used for signal amplification purposes. Offering excellent fidelity, the GX1222 amplifies signals from DC to over 20 MHz with a fixed gain of x10. Custom gains are also available without compromising signal purity and amplifier performance.
-
product
PXIe Dual Channel 20GHz 30dBm RF Amplifier
3202
Model TE3202 is a dual channel RF amplifier in a single slot PXIe form factor that can operate from 100kHz to 20GHz, designed for high frequency, and high power signal amplification.
-
product
PXIe Single Channel 20GHz 30dBm RF Amplifier
3201
Model TE3201 is a single channel RF amplifier in a single slot PXIe form factor that can operate from 100kHz to 20GHz, designed for high frequency, and high power signal amplification.
-
product
Signal Amplifier
9260
The 9260 is a bench-top, 2U, half 19” rack size, fully metal case, dual channel DC coupled wideband amplifier designed for high frequency, high current, signal amplification. With a high bandwidth of 45MHz, 34Vp-p into 50 ohms and up to 10W output power, the 9260A is the ideal complimentary amplifier to any signal source that needs a supporting power boost for demanding applications.
-
product
Signal Amplifier
9250
The 9250 is a bench-top, 2U, half 19” rack size, fully metal case dual channel amplifier. The instrument can be configured to be used as two, single-ended independent channels, or as a one input with two differential outputs.
-
product
Signal Amplifier
A10150
Model A10150 is an ultra-small footprint, wideband, DC coupled amplifier designed for high frequency, low distortion, signal amplification. With a high bandwidth of 150MHz, 20Vp-p into 50 ohms and a fast transition time of less than 1.8ns, the A10150 is the ideal complimentary amplifier to any high speed signal source that needs a supporting power boost for demanding applications.
-
product
Signal Amplifier
A10160
Model A10160 is an ultra-small footprint, wideband, DC coupled amplifier designed for high frequency, high current, signal amplification. With a high bandwidth of 45MHz, 34Vp-p into 50 ohms and up to 10W output power, the A10160 is the ideal complimentary amplifier to any signal source that needs a supporting power boost for demanding applications.
-
product
Signal Amplifier
9100
Model 9100 is a Single/Dual Channel, 2U, half-rack size, bench-top power amplifier designed for signal amplification. With unprecedented signal purity, Model 9100 amplifies signals from DC to over 500kHz. The unit has a fixed gain of x15 however the same amplifier is available with custom gain and no signal purity or performance degradation whatsoever.
-
product
Signal Amplifier
9400
Model 9400 was designed as a general purpose, wide band and high voltage amplifier however, with specific applications in mind. It has four channels built in a small case size to save space and cost but without compromising bandwidth and signal integrity.
-
product
Signal Amplifier
9200A
Model 9200A was designed as a general purpose, wide band and high voltage amplifier however, with specific applications in mind. It is built in a small case size to save space and cost but without compromising bandwidth and signal integrity.
-
product
Signal Amplifier
9200
Model 9200 is a Single/Dual Channel, 2U, half-rack size, bench-top power amplifier designed for signal amplification. With unprecedented signal purity, Model 9200 amplifies signals from DC to over 500kHz. The unit has a fixed gain of x15 however the same amplifier is available with custom gain and no signal purity or performance degradation whatsoever.
-
product
Signal Amplifier
9100A
Model 9100A was designed as a general purpose, wide band and high voltage amplifier however, with specific applications in mind. It is built in a small case size to save space and cost but without compromising bandwidth and signal integrity.
