Showing results: 2971 - 2985 of 3167 items found.
-
DM84 -
Lectrosonics, Inc.
The DM84 is an 8-in, 4-out digital matrix processor with the capability to route any combination of inputs to any combination of outputs with extremely low throughput latency. Automatic microphone mixing is accomplished via a patented Adaptive Proportional Gain algorithm. Sophisticated filtering is offered on each input and output. A compressor is available on each input, a compressor and limiter on each output. In addition, each input and output can be configured with a delay setting of up to 100 ms for inputs, 250 ms for outputs. The DM84 runs on the latest-generation DSP architecture and can be integrated as part of a larger system by connecting other DM units (like the DMTH4) via the Digital Audio Network Interface (DANI) bus.
-
Shoghi Communications Ltd.
Satellite Phone (GMPCS-Global Mobile Personal Communications by Satellite) is a terminal device act like a normal mobile. Satellite phones connect to satellites orbiting around the earth. Satellite phones rely on a network of satellites that are either fixed above the Equator (Geostationary) or in Low Earth Orbit (LEO) anywhere from 500 to 1,000 miles above the earth. Satellite phones are rarely affected by violent storms and depending upon their system architecture they can work virtually anywhere in the world. The satellite phone is the best mode of communication where no cellular coverage exists. The most popular Satellite phones are from Thuraya, iridium, and Inmarsat (IsatPhone, IsatPhone Pro and IsatPhone 2).
-
RFCI61000-4-6 -
Lisun Electronics Inc.
RFCI61000-4-6 RF Conducted Immunity Test System is an automatic test system which is for the conduction sensitivity testing, it is fully meets IEC61000-4-6.2006, ISO11452-4, GB/T17626.6-2008 and GTB152B-CS114 etc standards. RFCI61000-4-6 internal source and broadband power amplifier can be generated 3 voltage test levels: 1v, 3v and 10v, and has the function of the real detect output level. It has two operation software which is calibration software and test software. When measuring, the signal is in 1 KHZ sine wave amplitude modulation system (80%) to simulate the actual harassment, and can through the coupling/decoupling network (CDN or electromagnetic clamp) to make the harassment signal coupled to the device.
-
CODA-4782 -
Hitron Americas Technologies Inc.
The CODA-4782 has the capability to receive 5Gbps based on 2 x OFDM + 32 QAM over its DOCSIS 3.1 interface. The integrated Wi-Fi 3×3 2.4 GHz 802.11n and 4×4 5 GHz 802.11ac Wave 2 dual band MU-MIMO Access Point significantly improves customer experience extending range and coverage with blazing speeds. For wired clients, the four Gigabit Ethernet ports offer ultra-fast connections. MoCA 2.0 bonding provides a near-Gigabit wired backbone in the customer’s home for Wi-Fi extension. Its switchable upstream (5~85/5~204MHz)offers the possibility of flexible integration to existing networks.
-
CODA-4789 -
Hitron Americas Technologies Inc.
The CODA-4789 has the capability to receive 5Gbps based on 2 x OFDM + 32 QAM over its DOCSIS 3.1 interface. The integrated Wi-Fi 3×3 2.4 GHz 802.11n and 4×4 5 GHz 802.11ac Wave 2 dual band MU-MIMO Access Point significantly improves customer experience extending range and coverage with blazing speeds. For wired clients, the four Gigabit Ethernet ports offer ultra-fast connections. MoCA 2.0 bonding provides a near-Gigabit wired backbone in the customer’s home for Wi-Fi extension. Its switchable upstream (5~85/5~204MHz) offers the possibility of flexible integration to existing networks.
-
CODA-4682 -
Hitron Americas Technologies Inc.
The CODA-4682 has the capability to receive 5Gbps based on 2 x OFDM + 32 QAM over its DOCSIS 3.1 interface. The integrated Wi-Fi 3×3 2.4 GHz 802.11n and 4×4 5 GHz 802.11ac Wave 2 dual band MU-MIMO Access Point significantly improves customer experience extending range and coverage with blazing speeds. For wired clients, the four Gigabit Ethernet ports offer ultra-fast connections. MoCA 2.0 bonding provides a near-Gigabit wired backbone in the customer’s home for Wi-Fi extension. Its switchable upstream (5~42/5~85MHz) offers the possibility of flexible integration to existing networks.
-
DAS-429UNET/RTx -
Excalibur Systems, Inc.
Our DAS-429UNET/RTx is an intelligent, multichannel ARINC 429 interface device that can be connected to any Windows device with a USB or Ethernet connector. It monitors and records all or selected 429 traffic for later analysis or reconstruction in the lab. Exalt is our Windows base graphical tool that allows you to analyze real time or recorded data using many different views: raw data, engineering units or graphical displays.Data can be then extracted from the recorded file, and re-transmitted over the bus to another system in order to see in detail what happened during the recorded test.The combination of a handheld computer, 429Unet card and Exalt provides a complete solution for testing and maintaining ARINC-429 networks.
-
TS-LBS -
Rohde & Schwarz GmbH & Co. KG
The R&S®TS-LBS is a comprehensive test solution for network and satellite based location technology testing of wireless devices and chipsets.It is highly configurable for testing various location technologies and uses Rohde & Schwarz location based test systems.The R&S®TS-LBS test system family fulfills the requirements of LBS conformance testing and operator acceptance testing on GSM, WCDMA, LTE and 5G devices and chipsets as well as regulatory testing consisting of adjacent channels and spurious emissions for EN 303 413 receiver testing. It also fulfills the requirements of E112 (EU) 2019/320 testing consisting of GNSS testing such as Galileo and AML mobile testing.
-
CMWrun -
Rohde & Schwarz GmbH & Co. KG
The R&S®CMW is the leading multistandard UE testing platform used by network operators, test houses, handset vendors and chipset manufacturers worldwide. R&S®CMWrun automation software meets all requirements for executing remote control test sequences on the R&S®CMW for wireless equipment in R&D, quality assurance, production and service. The intuitive graphical user interface of the R&S®CMWrun sequencer software allows easy and straightforward test sequence configuration. No programming and code compilation are needed. At the end of the test, an easy-to-read test report of the limits, test results and verdict is generated.
-
Rohde & Schwarz GmbH & Co. KG
With the R&S®RF Ports Alignment software together with the option R&S®SMW-K545, Rohde & Schwarz provides a standard and tailored solution for calibrating amplitude, time and phase of multi-channel SMW setups. The RF Port Alignment automatically collects the gathered correction data for the multi-channel setup using a connected vector network analyzer such as the R&S®ZNA or R&S®ZNB. Thanks to an intuitive graphical user interface the test engineer is guided through the calibration procedure step-by-step in a convenient way. With a calibrated multi-channel setup, tests of advanced systems in wireless communication or of radar receivers can be performed straightforward.
-
780687-02 -
NI
2-Port, High-Speed, Flexible Data Rate PXI CAN Interface Module—The PXI‑8512 is a high-speed Controller Area Network (CAN) Flexible Data-rate (FD) interface for developing applications with the NI‑XNET driver. The PXI‑8512 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimize message latency and freeing host processor time for processing complex models and applications.
-
LVD-415 -
Standard Electric Works Co., Ltd
● No batteries required.● Every circuit is doubled.● Buzzer indicates voltage detected.● Led indicates voltage detected.● Neon scale indicates voltage.● Dual HBC fuses.● High grade fiber glass probes.● Super polished fiber glass.● High strength connecting cord.● Heavy duty rated.● Replaceable tips.● Choice of tips available.● Lightweight.● Small storage space.● Strong strength reliefs.● Double poles non-polarized.● Suitable for 45 to 70 Hz networks.● Contact detector type.● Passive circuitry.● Fiber glass 1.6mm - CU 35um PCB.● Super bright neon lights and LEDs.● Ergonomically-designed.● EN 61010-031 CAT IV 500V.
-
785640-01 -
NI
8-Channel Temperature Input Device for FieldDAQ - The FD-11613 measures up to eight thermocouple channels. It features cold-junction compensation and open thermocouple detection with an LED indicator per channel to identify disconnected thermocouples. The FD-11613 has an ingress … protection rating up to IP67 (dust- and water-resistant), can operate in -40 °C to 85 °C environments, and can sustain 100 g shock and 10 g vibration. The FD-11613 incorporates Time Sensitive Networking (TSN) and features an integrated network switch and built-in power circuitry for simple daisy chaining. You program the FD-11613 with NI-DAQmx, which automatically synchronizes multiple FieldDAQ™ devices. This device is ideal for test cell and outdoor environments.
-
781910-01 -
NI
20 MHz Bandwidth, 50 MHz to 2.2 GHz, Included GPS-Disciplined OCXO, USRP Software Defined Radio Device - The USRP‑2930 is a tunable RF transceiver with a high-speed analog‑to‑digital converter and digital‑to‑analog converter for streaming baseband I and Q signals to a host PC over 1 Gigabit Ethernet. It also features a GPS-disciplined oscillator (GPSDO) with PPS accuracy of ±50 ns. You also can use the NI USRP‑2930 for the following communications applications: white space; broadcast FM; public safety; land-mobile, low-power unlicensed devices on industrial, scientific, and medical (ISM) bands; sensor networks; cell phone; amateur radio; or GPS.
-
781060-01 -
NI
The PCI‑8531 is a high-speed CANopen interface for developing applications with the NI‑Industrial Communications for CANopen driver. CANopen is the application layer that sits on top of the CAN physical layer often used for industrial automation … applications. CANopen was designed for motion-oriented machine control networks, such as handling systems, but now it is used in a variety of products and applications, including medical equipment, off-road vehicles, maritime electronics, public transportation, and building automation. The PCI‑8531 can transmit or receive process data objects (PDOs) and service data objects (SDOs) according to CiA‑DS 301. It also features a batch SDO editor with EDS file integration and LSS services support for slave node configuration.
