Showing results: 1951 - 1965 of 4207 items found.
-
Smiths Interconnect
Our Multi-Function RF Systems incorporating TRAK and Millitech technologies include compact ultra-low phase noise and spurious frequency sources and exciters, high dynamic range block and tuned frequency converters, receivers and receiver protectors, amplifiers, for harsh military, aerospace and space environments enabling EW, communication, satcom, remote sensing, and datalink systems.
-
WGNS -
Farran Technology Ltd
The system allows the user to extend the frequency range of the NFA to allow for accurate noise figure measurements to be performed on a device operating in the 26.5 – 170GHz range on wafer as well as in benchtop applications. Farran offers the WGNS series of noise sources to be used in conjunction with the FBC down converters for use as frequency extenders for noise figure measurement test system.
-
3520 Series -
KANOMAX USA, Inc.
The Kanomax Piezobalance Dust Monitor 3521/3522 is a unique respirable aerosol monitor, providing direct mass concentration of particulates using PIEZOBALANCE technology; ideal especially for oil mist monitoring. The Kanomax 3521 is equipped with 4 and 10µm impactors while the 3522 is equipped with a 2.5µm impactor. Unlike conventional dust meters, which count particles, a piezobalance dust meter like the 3521 or 3522 “weighs” mass concentration of particulates. As an air sample enters the system, it travels through the impactor, which captures and removes larger particulates away from the sample. Smaller particulates become electrically charged and deposited on the piezo-crystal. The total mass of the deposited particulates affects the piezo-crystal’s frequency. Since the change in frequency is proportional to the mass of the particulates, the actual weight of the particulates is obtained.
-
ERAVANT
Conical gain horns are offered as both standard and custom models with either a circular or rectangular waveguide interface. While conical gain horns with a rectangular waveguide interface can only support linear polarization, models with a circular waveguide interface can support various polarization types including horizontal, vertical, left-handed circular, and right-handed circular polarization for broader applications. The listed models operate across the full waveguide band and offer 23 dB nominal gain, 12 degrees typical half power beamwidth, a 24 dB typical side lobe level and 1.15:1 VSWR at center frequency. The below standard offering covers the frequency range of 8.5 to 140 GHz. However, other frequencies and standard models with 10, 15, 20 and 25 dB gain are also available.
-
-
A0040A -
SYCATUS Corp
Optical Noise Analyzer is the industry first solution for evaluation of optical frequency noise of lasers as power spectrum density.
-
CG118 -
EMC Instruments Corporation
The main application of comb generator is to quickly verify 1GHz above radiated emission and conducted emission test setup.And the most important application is 3m chamber and 10m chamber 1GHz above to18GHz with 250MHz frequency spacing for site validation,shielding efficiency. reference signal source Noise Generators Signal Generators
-
SDG5000 Series -
SIGLENT Technologies
Siglent Technologies invented the pulse generator algorithm EasyPulse, which is found in the SDG5000 waveform generators. Based on this new technology, the SDG5000 is capable of generating a pulse signal with low jitter, fast rising and falling edge (frequency independent effect), small duty cycle, edge and pulse width can be a wide range of adjustment.
-
PD5021 -
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.2 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)50 VDC maximum on DC block portOutdoor Weatherproof ConstructionTri Alloy N Type Female (Jack) 50 Ohm
-
IQD Series -
EM Research, Inc.
*Capable of receiving RF and LO frequency inputs *Output from DC to 500 MHz *Internal low noise oscillator Internal reference *Buffered demodulator *Balanced IQ *Optimized for low EVm *Optional internal Reference Detect Switch (EM Research RDS Series) *Up to 250 mega-symbols per second
-
EB-C251 -
Ceibo Inc.
# Real-Time and Transparent C251 Emulation# supports Intel MCS?251 and Atmel/W&M/Temic C251# Uses Bond-Out Technology# Maximum Frequency Support up to 24MHz# Source-Level Debugger for C, PLM and Assembler# MS-Windows Software# Support for ROMless and ROMed Microcontrollers# 256K Internal Memory# Memory Mapping Capabilities# Real-Time Trace
-
Tampa Microwave
Tampa Microwave''s satellite simulators provide a compact easy to use training and evaluation tool for satellite earth terminals. We provide a variety of models with different combinations of frequency bands, transmit/receive strength, atmospheric effects and form factors. Contact us with your requirements and we will recommend a cost effective solution.
-
Interface Trap Density Analysis Option -
Materials Development Corporation
MDC offers interface trap density analysis using both the Conductance-Frequency and Quasi-statictechniques. The Conductance-Frequency method is recommended for fine-tuning of processes where the highest resolution is needed. The Quasi-static technique is recommended where moderate to high levels of interface traps are monitored, such as in radiation damage studies. Requires quasi-static option or variable frequency option.
-
Daqarta
The Sound Level Meter is shown positioned near the top of the main Daqarta window. Like the Voltmeter and Frequency Counter, it can be positioned anywhere on the screen, and the size of the display font changes when you resize the meter by dragging its borders. You can fill the screen for a really big readout that can be seen from across the room.
-
Talon Meters
Engineered specifically for troubleshooting Variable Frequency Drives and Power Inverters the Talon VFD / Inverter Meter is your key to positive results. Not only that, this meter is easier to use than a standard multi-meter and can save more money than it costs the very first time you use it to fix a piece of equipment instead of replacing it.