Showing results: 3436 - 3450 of 4207 items found.
-
LS-96 SYNC -
Standard Electric Works Co., Ltd
● Input Voltage : 110V AC, 120V AC, 220V AC, 230V AC or 240V AC.● Square shape panel 96 x 96mm● 3 bi-colored LED indicators for "SYNC", "GEN" and "BUS"● 24 LEDs in a circle display the phase angle and the frequency differences between 2 networks● 360° indication● 12 o'clock position LED is bi-colored● PC window, ABS resin frame, PC case
-
1812 EL -
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● 2Lines × 16 Characters LCD.● Very low consumption.● Menu-driven.● Accurate digital readout of disconnection time.● Automatic data hold function.● Zero Crossing Circuitry permit testing at 0° or 180°.● Disconnection Phase Polarity shown on LCD display.● Auto-off and off override.● Polarity Trip indicator (Positive of Negative Phase).● Wiring polarity indicator.● Measure voltage and frequency between Line and Earth before testing.
-
M9381A -
Keysight Technologies
Choose your RF modulation bandwidth, 40, 100, or 160 MHz, and easily upgrade as test needs change Increase throughput with fastest RF frequency tuning and amplitude switching for high-speed automated test Save space with a compact solution for up to 8x8 MIMO with phase coherence Get up and running quickly with validated application-specific reference solutions Simplify signal creation with Keysight's Signal Studio and Waveform Creator
-
Micropross MP500 PT1-NFC -
NI
Support for ISO 14443 A/B, ISO 15693, MIFARE™, FeliCa™. Measurement correlation with NFC Forum and EMVCo certification test bench. Automated test executive with ready-to-run test sequences. Reader/Writer and Card Emulation modes, resonance frequency measurements supported on same antenna. Embedded analog measurements - LMA, field strength, S11, Q factor, waveform characteristics. Physical parameter/waveshape characteristic definition
-
EM-6947 | 200 MHz – 5 GHz -
Electro-Metrics Corp.
The EM-6947 is an ultra-wide bandwidth log periodic dipole array aimed at applications requiring consistent performance over a very wide frequency range. Capable of both receiving and moderate power level transmitting, the EM-6947 can take the place of two or more conventional antennas, allowing you to take full advantage of the tuning range capabilities of modern receiver and spectrum analyzer designs with less inconvenience caused by the need to switch antennas.
-
MS 1806 -
Meltronics Systemtech
*TTL Pulse measurement channels (Timers / Counters) 18 Channels*TTL Pulse Generation - 12 Channels*The Pulse Generation Frequency from 10Hz to 40MHz*The no. of pulses controlled from 1 to 255 pulses*All Channels are compatible with 5V TTL / CMOS*All the pulse input and the output signals driven through Pin Driver*Standard ISA Bus Interface*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
PQM-703 -
Sonel S.A.
Power quality analyzer PQM- 703 is a technically advanced product that allows for comprehensive measurements of the quality of electricity , analysis and recording of power network parameters, for frequencies 50/60 Hz in accordance with European standard EN 50160. PQM -703 is another representative of a well, known family of analyzers line PQM- 70x . In relation to the PQM -702 has new functions like recording of transients with max. sampling frequency 10 MHz (rapid changes in voltage) and control signals. Minimal transient capturing time is 650 ns. It is intended for a very wide range of users who need to control the quality of power with a mobile device , which fulfills the requirements of a multi-sheet standard IEC 61000 for class A analyzers. This applies to measurement accuracy, measurement methods, and synchronization of time with a standard signal. The last condition is met with a built-in GPS module with an internal antenna. If the analyzer is installed inside, it is possible to use an additional antenna with a 10m-long wire. If the antenna is situated outside, GPS signal will be attainable without any problems and used for the synchronization of an internal clock.
-
Model 52624 -
Pentek, Inc.
- Modifies 34 IF signals between input and output- Up to 80 MHz IF bandwidth- Two 200 MHz 16-bit A/Ds- Two 800 MHz 16-bit D/As- 34 DDCs and 34 DUCs (digital downconverters and digital upconverters)- Signal drop/add/replace- Frequency shifting and hopping- Amplitude boost and attenutation- PCI Express Gen 1: x4- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
NP-7310 -
Ono Sokki
NP-7310 is the accelerometer with built-in preamplifier, and capable of tri–axial directions simultaneous measurement. It is suitable for the low frequency vibration measurement such as ground vibration or floor vibration while operating the machine. NP-7310 can be used with the sensor amplifier unit such as AU-2100, AU-2300 or PS-1300. Also, it is possible to input directly to the analyzer or recorder which the constant current amplifier is built-in such as the FFT Analyzer of DS-2000 series, DS-3000 series, CF-7200A, CF-9000 series or CF-3650/3850 series.
-
SASI -
Textron Systems
Textron Systems’ SASI 240 is a Signal Analysis Synthetic Instrument that combines the capabilities of six distinct measurement systems into a single device. Our dual-channel architecture enables two independent radio frequency (RF) measurements to be run simultaneously. Whether used as a benchtop device or an integrated automated test equipment (ATE) RF subsystem, our SASI’s simple and intuitive graphical user interface (GUI) ensures easy, out-of-the box functionality.
-
GT668PXIe -
Guide Technology, Inc.
GuideTech’s GT668PXIe PXI 3U form factor, meets industrial standard chassis with an expandable platform, achieving optimal test system at low cost. High accuracy 100MHz time base with NIST traceable calibration. Some of the GT668PXIe-1 measurements include Jitter measurements, PLL & Clock Jitter, Spread Spectrum Modulation, PLL Lock Time, Frequency, Period, Pulse Width, Skew, Tpd, Rise/Fall Time, Time Interval Error and more.
-
Pickering Interfaces Ltd.
Programmable RF Attenuators – accurate DC to 3GHz programmable attenuator has a 1dB step resolution, allowing it to adjust signal amplitudes for optimum measurement by other devices.Solid State Programmable RF Attenuators – available in triple or hex formats with bandwidths between 10MHz and 6GHz.High Voltage Attenuators – provide a convenient way of attenuating high voltage low frequency signals to levels that can be captured by other PXI devices without risk of damaging them.
-
KH3938B -
Beijing KeHuan Century EMC Technology Co,.LTD
Is a fully automatic radio disturbance test receiver and is the main tool for EMI testing. KH3938B receivers frequency range 9kHz-1GHz, in accordance with: 2010 and GB / T6113.101-2016 development standards designed to meet the requirements of the standard-compatible, can be used to power emission test, Sao conduction disturbance voltage test, radiated disturbance within 1G test. The receiver has the advantages of fast test speed , strong maneuverability, stable performance, and convenient test data processing.
-
Renesas Electronics Corp.
Renesas' portfolio of transister arrays include NPN, PNP, NPN-PNP combination transistor arrays based on our complementary UHF-1 SOI process. This portfolio also includes ultra high frequency transistor arrays for VHF/UHF amplifiers, VHF/UHF mixers, IF converters, synchronous detectors. Dual long-tailed pair transistor arrays and Gilbert Cell UHF transistor arrays are also available for wireless communication systems, radio and satellite communications and high performance instrumentation.
-
Analog Devices Inc.
Analog Devices signal generators provide an ideal solution for applications such as wireless HDMI®, microwave and millimeterwave radio, and sensor equipment. These products offer a clean signal, broad frequency coverage, and high output power for multiple applications, with competitive functionality and performance against other signal generators in their class. Our technology operates up to the 70 GHz range, and includes bench top and portable options for greater flexibility in design and development.
