Showing results: 3601 - 3615 of 4207 items found.
-
N9936A -
Keysight Technologies
100 kHz to 14 GHz frequency range Expand capabilities with optional tracking generator, interference analyzer, built-in power meter, and more Make accurate spectrum analyzer measurements ( 0.5 dB) without needing warm-up Locate interfering signals using the intuitive spectrogram display and recording capability Easily measure average and pulse power with a USB power sensor, pulse measurements with time gating Lightest microwave handheld spectrum analyzer at only 6.6 lb. (3.0 kg)
-
N9951A -
Keysight Technologies
44 GHz max frequency Carry world's most integrated handheld W analyzer: standard model includes cable and antenna analyzer Expand capabilities with optional VNA, spectrum analyzer, built-in power meter, vector voltmeter, and more Save time by measuring DTF and TDR in a single sweep Simultaneously measure all four S-parameters Make accurate SA measurements ( 0.5 dB) without needing warm-up Easily measure average and pulse power with a USB sensor
-
J2180A -
PICOTEST Corp.
The J2180A low noise preamplifier provides a fixed, AC coupled 20dB gain while converting a 1 MOhm input impedance to a 50 Ohm output impedance. With a 3dB bandwidth of 0.1Hz to 100MHz, the preamplifier improves the sensitivity of oscilloscopes, network analyzers and spectrum analyzers while reducing the effective noise floor and spurious response. The preamplifier can also serve as a low frequency DC blocker for a spectrum analyzer or you can use it to connect a high input impedance oscilloscope probe to 50 Ohm equipment.
-
E5081A -
Keysight Technologies
Our spectral correlation technique directly analyzes the modulated input and output signals in the frequency domain on the network analyzer. Current solutions on the market require a network and spectrum analyzer to characterize components fully. With the new ENA-X, you can ensure test accuracy and repeatability with a single test setup using full vector correction at the DUT plane. Avoid manually reconfiguring setups or automating complex switch-based systems — verify device performance faster and with less error potential with the ENA-X network analyzer.
-
N9938A -
Keysight Technologies
100 kHz to 26.5 GHz frequency range Expand capabilities with optional tracking generator, interference analyzer, built-in power meter, and more Make accurate spectrum analyzer measurements ( 0.5 dB) without needing warm-up Locate interfering signals using the intuitive spectrogram display and recording capability Easily measure average and pulse power with a USB power sensor, pulse measurements with time gating Lightest microwave handheld spectrum analyzer at only 6.6 lb. (3.0 kg)
-
N9960A -
Keysight Technologies
5 kHz to 32 GHz frequency range Expand capabilities with optional tracking generator, interference analyzer, built-in power meter, and more Make accurate spectrum analyzer measurements ( 0.5 dB) without needing warm-up Locate interfering signals using the intuitive spectrogram display and recording capability Easily measure average and pulse power with a USB power sensor, pulse measurements with time gating Lightest microwave handheld spectrum analyzer at only 7.1 lb. (3.2 kg)
-
N9937A -
Keysight Technologies
100 kHz to 18 GHz frequency range Expand capabilities with optional tracking generator, interference analyzer, built-in power meter, and more Make accurate spectrum analyzer measurements ( 0.5 dB) without needing warm-up Locate interfering signals using the intuitive spectrogram display and recording capability Easily measure average and pulse power with a USB power sensor, pulse measurements with time gating Lightest microwave handheld spectrum analyzer at only 6.6 lb. (3.0 kg)
-
N9935A -
Keysight Technologies
100 kHz to 9 GHz frequency range Expand capabilities with optional tracking generator, interference analyzer, built-in power meter, and more Make accurate spectrum analyzer measurements ( 0.5 dB) without needing warm-up Locate interfering signals using the intuitive spectrogram display and recording capability Easily measure average and pulse power with a USB power sensor, pulse measurements with time gating Lightest microwave handheld spectrum analyzer at only 6.6 lb. (3.0 kg)
-
N9961A -
Keysight Technologies
5 kHz to 44 GHz frequency range Expand capabilities with optional tracking generator, interference analyzer, built-in power meter, and more Make accurate spectrum analyzer measurements ( 0.5 dB) without needing warm-up Locate interfering signals using the intuitive spectrogram display and recording capability Easily measure average and pulse power with a USB power sensor, pulse measurements with time gating Lightest microwave handheld spectrum analyzer at only 7.1 lb. (3.2 kg)
-
Keysight Technologies
Keysight's power limiters provide the best broadband input protection from excess RF power, DC transients and ESD, for a variety of RF and microwave instruments and components. For example, the input circuitry of spectrum analyzers, network analyzers, frequency counters or amplifiers can be protected from unintentional inputs up to 5 watts average power. At even greater power levels, failure mode for the limiter is either an open circuit or a short circuit to ground, thereby protecting the instrument from damage.
-
N9950A -
Keysight Technologies
32 GHz max frequency Carry world's most integrated handheld W analyzer: standard model includes cable and antenna analyzer Expand capabilities with optional VNA, spectrum analyzer, built-in power meter, vector voltmeter, and more Save time by measuring DTF and TDR in a single sweep Simultaneously measure all four S-parameters Make accurate SA measurements ( 0.5 dB) without needing warm-up Easily measure average and pulse power with a USB sensor
-
785041-01 -
NI
500 S/s, ±20 mA, 16-Channel C Series Current Input Module - The NI‑9208 is designed with industrial systems in mind. It includes a high-resolution mode with 50/60 Hz rejection to remove low frequency noise. It has high-channel density to reduce the number of modules needed, which leaves slots open for other measurement types or for reducing the overall per channel cost of the system. The NI‑9208 uses a standard D‑SUB connection for use with cables and connector blocks.
-
780968-02 -
NI
500 S/s, ±20 mA, 16-Channel C Series Current Input Module - The NI‑9208 is designed with industrial systems in mind. It includes a high-resolution mode with 50/60 Hz rejection to remove low frequency noise. It has high-channel density to reduce the number of modules needed, which leaves slots open for other measurement types or for reducing the overall per channel cost of the system. The NI‑9208 uses a standard D‑SUB connection for use with cables and connector blocks.
-
780968-01 -
NI
500 S/s, ±20 mA, 16-Channel C Series Current Input Module - The NI‑9208 is designed with industrial systems in mind. It includes a high-resolution mode with 50/60 Hz rejection to remove low frequency noise. It has high-channel density to reduce the number of modules needed, which leaves slots open for other measurement types or for reducing the overall per channel cost of the system. The NI‑9208 uses a standard D‑SUB connection for use with cables and connector blocks.
-
425A -
Novatech Instruments , Inc.
The 425A generates sine, LVDS and LVCMOS outputs simultaneously and is programmable in 10µHz steps from 250kHz to 350MHz and includes an LVCMOS Prescaler and Divider for generating LVCMOS frequencies down to 2 Hz. The 425A is controlled by an RS232 serial interface. Phase can be programmed with 14-bit resolution. The Frequency is accurate to 1.5ppm when using the on board TCXO timebase or you can use an external timebase. It requires 5 VDC power. A Line Voltage AC Adapter is included. SOF8_425 windows software is also included.
