Filter Results By:
Products
Applications
Manufacturers
-
product
AC Magnetism Measurement Equipment
TWM
This equipment is used for measurement analysis of magnetic characteristics in high frequency by commercial frequency of soft material sample such as magnetic steel sheet and amorphous etc., and for quality control of product and material research. It is possible to apply single sheet sample, ring type of sample and Epstein sample etc.
-
product
Frequency Monitors
FM Series
FM Series line-powered frequency monitors are high quality, dependable panel meters designed to continuously monitor line power frequency. Crystal reference-based for high accuracy, these 1/8 DIN/NEMA case style meters come with LED or LCD displays.
-
product
FFT Comparator
CF-4700
The CF-4700 FFT comparator is a pass/fail judgment machine used on production lines that is highly effective in accurate quality inspection by analyzing sound or vibration from products. As being incorporated our accumulated FFT technology over the years, the CF-4700 enables pass/fail judgment by extracting the amount of fluctuation of signal size focusing on a specific frequency band.
-
product
Socket Wrench Torque Sensor Reaction Type
SWS SERIES
Our SWS Series reaction type socket wrench torque sensors are available in ranges from 10 ft-lbs. through 1000 ft-lbs. and provide accurate measurements of bolt or nut wrenching torques. These sensors are bi-directional so both tightening and break-away torques can be measured. These low cost sensors deliver high accuracy and outstanding frequency response. alibration of mechanical torque wrenches may be performed with this sensor. The sensing element incorporates bonded foil strain gages of the highest quality.
-
product
AC Magnetic Automatic Measurement Equipment
ESS
This automatic measurement equipment to measure magnetic property in commercial frequency is used for quality control and research of materials. It is possible to apply single sheet sample and Epstein sample etc. Sine wave measurement can be made within the range of measurement frequency of 50Hz ~ 400Hz. Measurement of basic magnetic property [B,H,P,S,µ] can be made.
-
product
Interference Locating System
SeeWave®
Interference impacts wireless network coverage and quality of service, but hunting interference in the field can be expensive and time-consuming. PCTEL’s SeeWave® interference locating system enables a single user to accurately detect the interfering frequency and locate its exact source.
-
product
Hydrodynamic 33 kHz and 200 kHz Dual Frequency Transducer
Model TC2178
Model TC2178 is an optimized and hydrodynamic 33 kHz and 200 kHz dual frequency transducer ideal for navigation and hydrographic echosounder systems. The transducer has excellent piezoceramic elements which will ensure the highest reliability and quality in echosounding.
-
product
Digiair PRO ATSC
Perfect for digital terrestrial installations (ATSC).• Handy spectrum-analyzer for frequency 45-862MHz.• Easy digital readout of BER and SNR.• Ready for Mpeg2 and Mpeg4 signals.• Analog signal level reads out in dBuV.• Presents one channel readout with high resolution or sixchannels simultaneously or the complete spectrum.• Very sensitive, easy to maximize weak and strong signals.• Built in beeper (pitch tone) and maxhold function.• Aerial power output, 0V, 5V, 12V and 24V.• Built in, rechargeable battery.• Power supply and car-charger enclosed.• Carrying-case enclosed.• Made in Sweden.
-
product
Digair PRO ISDB-T
Perfect for digital terrestrial installations (ISDB-T).• Handy spectrum-analyzer for frequency 45-862MHz.• Easy digital readout of BER and SNR.• Ready for Mpeg2 and Mpeg4 signals.• Analog signal level reads out in dBuV.• Presents one channel readout with high resolution or six channelssimultaneously or the complete spectrum.• Very sensitive, easy to maximize weak and strong signals.• Built in beeper (pitch tone) and maxhold function.• Aerial power output, 0V, 5V, 12V and 24V.• Built in, rechargeable battery.• Power supply and car-charger enclosed.• Carrying-case enclosed.• Made in Sweden.
-
product
Digiair PRO CATV
Perfect for digital CATV installations (QAM).• Handy spectrum-analyzer for frequency 45-860MHz.• Easy digital readout of MER, BER and Constellation diagram.• QAM16, QAM32, QAM64, QAM128 & QAM256.• Analog signal level reads out in dBuV, dBmV and dBm with maxholdfunction.• Presents one channel readout with high resolution or six channelssimultaneously or the complete spectrum.• Very sensitive, easy to maximize weak and strong signals.• Built in beeper (pitch tone) and maxhold function.• Tilt function.• Replacable, rechargeable battery (8x AA 1200mA).• Power supply and car-charger enclosed.• Rubber carrying-case enclosed.
-
product
Digiair PRO
Frequency range of 45-860MHz.• The meter to use for easy Digital terrestial installations.• Very sensitive, easy to maximize weak and strong signals.• Signal level reads out in dBuV.• Presents one channel readout with high resolution or six channels.simultaneously or the complete spectrum.• Built in beeper (pitch tone) and maxhold function.• Aerial power output, 0, 5 and 12V.• Built in, rechargeable battery.• Power supply and car-charger enclosed.• Carrying-case enclosed.• Small and handy design.• Made in Sweden.
-
product
Digital Power Meters
Switchboard meters with one, two or three digital readouts for measuring AC power parameters, including ACV, ACA, frequency, watts, vars, power factor, and phase angle.
-
product
Light-to-Frequency
Light-to-Frequency (LTF) sensors convert measurements of light intensity to a digital form for direct interfacing to a microcontroller. The output of the device is a square wave or pulse stream the frequency of which is linearly proportional to the light intensity. LTF converters are designed for applications such as ambient light measurement, light absorption/reflection in products such as white goods, photographic equipment, colorimetry, chemical analyzers and display contrast controls. They may be used in any system that requires a wide dynamic range, and/or high resolution digital measurement of light intensity.
-
product
Power Absorption Clamp
Beijing KeHuan Century EMC Technology Co,.LTD
Frequency Range: 30MHz-1GHz Typical Insertion Loss: 17 dB ± 4 dB Output Impedance: 50Ω Connector: N(f), 50Ω Maximum Current: 30 A
-
product
EMI Receiver
KH3931
Beijing KeHuan Century EMC Technology Co,.LTD
* Detection frequency range: 9KHz-30MHz * Frequency stability: 1X10-6 * Frequency resolution: (9kHz ~ 150kHz): 30Hz; (150kHz ~ 30MHz): 1kHz * Test error: ±2dB * Corresponding characteristics of pulse: in line with national standard GB/T6113.1-1995 * Detection time constant: in line with national standard GB/T6113.1-1995
-
product
Active Loop Antenna
KH30935
Beijing KeHuan Century EMC Technology Co,.LTD
KH30935 active loop antenna is used for adjusting, testing, measuring and other receivers. It has many advantages:1. The antenna coverage frequency is wide: 150KHz ~ 30MHz .2. The field strength value is measured according to the correction coefficient within the effective frequency range, which is convenient to use.3. The antenna has a small outer diameter and light weight, which is convenient for outdoor measurement.
-
product
Log-Periodic Antenna
KH30937F
Beijing KeHuan Century EMC Technology Co,.LTD
KH30937F log-periodic antenna (hereinafter referred to as KH30937F ) is a linearly polarized broadband receiving antenna with a working frequency of 30MHz~1GHz . KH30937F has excellent standing wave ratio characteristics, accurate feeding position, and the best phase relationship between each period on the base. The antenna gain is basically constant, thus ensuring that the antenna factor changes linearly and smoothly with the frequency, which is helpful for accurate difference calculation between each frequency point.
-
product
Pulse Limiter
KH43101
Beijing KeHuan Century EMC Technology Co,.LTD
1, frequency range 9KHZ~30MHZ 2, in-band loss 10dB+-1db 3, VSWR <1.25 4, allowable power <1 W 5, input impedance 50Ω (N type)
-
product
Active Dual Loop Antenna
KH30936
Beijing KeHuan Century EMC Technology Co,.LTD
KH30936 active dual loop antenna is used for adjusting, testing, measuring and other receivers. It has many advantages:1. The antenna coverage frequency is wide: 150KHz ~ 30MHz .2. The field strength value is measured according to the correction coefficient within the effective frequency range, which is convenient to use.3. The antenna power is supplied by the host, which is convenient for outdoor measurement.4. Compared with the single loop antenna, the advantage is to read the maximum value directly, which eliminates the tedious steps of rotating the antenna to find the maximum value and the interference of the human body to the signal.
-
product
Low Frequency Generator
LFG-200
LFG-200 is a cable test van-mountable signal generator used as part of a cable tracing and fault location set for the following applications.
-
product
Automated Electrical Insulating Gloves Tester
CBC-12C
Automated system СВС-12С is designed for electrical withstand testing of rubber insulating gloves with an AC voltage (UAC ≤ 10 kVRMS) at industrial frequency (f = 50 Hz).
-
product
Automatic Insulating Oil Dielectric Strength Tester
OLT Series
Portable automatic testers of OLT series are designed for dielectric strength testing of insulating oils (mineral and synthetic) with AC voltage up to 100 kVRMS at industrial frequency (f = 50 / 60 Hz).
-
product
Low Frequency Generator
LFG-2500
• tracing – finding the route and burial depth of the underground utilities;• fault location – pinpointing phase-to-sheath and interphase short-circuit faults;• cable identification – identifying a correct cable in a bunch.
-
product
Automatic Electrical Protective Equipment Test Systems
CBC-50С (CBC-100C)
Automatic systems CBC-C-series are designed for high-voltage withstand testing of electrical protective equipment and insulated hand tools. The tests are carried out with AC voltage (CBC-50C: UAC ≤ 50 kVRMS; CBC-100C: UAC ≤ 100 kVRMS) at industrial frequency (f = 50 Hz).
-
product
Electrical Protective Equipment Test Systems
СВС-50М (СВС-100М)
CBC-M-series systems are designed for high-voltage testing of electrical protective equipment and insulated hand tools. Withstand tests are carried out with AC voltage (CBC-50M: UAC ≤ 50 kVRMS; CBC-100M: UAC ≤ 100 kVRMS) at industrial frequency (f = 50 Hz).
-
product
Low Frequency Generator
LFG-50
• tracing – finding the route and determining the burial depth of underground cables and other hidden utilities;• fault location – pinpointing interphase and phase-to-sheath short circuits faults;• cable identification – identifying a correct cable from a bunch.
-
product
Low Freq. Pneumatic Levelling Mounts
ACE has a range of low frequency pneumatic levelling mounts under the designations PLM and PAL: they keep high performance and precision machines isolated from vibrations, impacts and force peaks.
-
product
Standards Waveform Generator
3110A
The 3110A software is built around the simple concept of a waveform segment. Each waveform segment can have a unique waveform, (sine, square, triangle, and/or DC offset). Frequency, amplitude and DC offset can be clipped, fixed, variable or swept. Segments can be calibrated (as required in CS101) and set to continue on to the next segment or to hold for an external trigger.
-
product
ODIN Laser/Radar Detector & Scrambler
ODIN Laser/Radar Detector & Scrambler uses the latest technology to detect and shift the frequency of incoming police radar signals, providing an effective defense against speeding tickets. This radar detector works with all existing radars on the market. It is an ideal choice for any driver looking for a reliable means of defense.
-
product
Magnetic Field Generator
PFM61000-8A
PFM61000-8A Magnetic Field Generator is high reliability test equipment with stable performance, specially designed for electrical and electronic products for measuring immunity characteristics and requirements of normal frequency magnetic fields. It provides an accurate basis for the tested equipment in the immunity test of normal frequency magnetic field. The generator can imitate the magnetic field environments such as residential, commercial, industrial and mining enterprises, power plants, as well as middle and high substation. It fully meets IEC61000-4-8 and GB / T17626.8 standards.
