Showing results: 1486 - 1500 of 8202 items found.
-
TP-ACC20-09 -
TEAM SOLUTIONS, INC.
The Accelerometer is a low cost, low power, complete dual-axis accelerometer with signal conditioned voltage outputs. The output signals are analog voltage proportional to acceleration. The Accelerometer is capable of measuring both positive and negative accelerations to at least +/- 2G.
-
ZAHNER-Elektrik
Electrostatic noise from the laboratory environment disturbs measurement signals and decreases data quality drastically for small current signals. Our Faraday Cage enables effective shielding for measurement on high impedance or low current samples.
-
Tekron International Ltd
Decode and validate your IRIG-B timing signals with Tekron's IRIG-B Analyzer. With multilevel signal support, the IRIG-B Analyzer enables accurate on-site fault diagnosis through a hand-held, rugged, portable and battery operated form factor.
-
RFATT AXIe-0 -
Holding Informtest
*Dual channel AXIe attenuator with frequency range from 9 kHz to 10 GHz.*The module is designed to work as part of information measuring systems as a normalizer of radio frequency signals (power control: signal amplification or attenuation).
-
multiLane
Optical clock-recovery modules are required when a clock signal is not present to trigger the oscilloscope or when it is better to use the embedded clock present in the data stream, such as for 100G Lambda optical signals.Clock-recovery modules are essential for transmitter signal characterization.
-
Heidenhain Corp.
Exposed linear encoders consist of a scale or scale tape and a scanning head. Their photoelectric scanning method is touch-free and wear-free, detecting graduation lines just micrometers in width and producing output signals with very short signal periods.
-
VX Instruments GmbH
An arbitrary waveform generator (ArbGen) is an extended function generator (FGen/FuncGen) that can generate freely programmable signals in addition to standard waveforms such as sine, square, triangle or trapezoid. In general, the voltage/current as well as the frequency/duration of the output signal can be freely adjusted.
-
ABex TM-4070 DMM -
Konrad Technologies GmbH
The ABex TM-4070 is an ABex terminal module to interface with NI PXI-407x or PXIe-408x and gives the possibility to rout the DMM signals to the front connector and the Analog bus. The routing to the analog bus is software controlled and the signals are switched with reed relays.
-
Studio Six Digital
Audio signal generator that include sine waves, square waves, white noise, and pink noise. The noise signals may be octave-band limited. In landscape mode, you can set sweep start and stop frequencies, and a time in seconds.
-
LV 5381 -
Leader Electronics Corp.
The LV 5381 is a waveform monitor that can monitor up to four SDI signals simultaneously.It is optimized for the level adjustment of the outputs of multiple installed cameras. In the video signal waveform display, vector display, and picture display, multiple input signals can be displayed on top of each other or lined up next to each other.It is also full of useful features such as a level meter display for embedded audio, an error display that indicates transmission errors, and a 5-bar display that shows video signal peak levels using five bars. Furthermore, the LV 5381 can show different combinations of these displays in its multi-screen display.
-
LKVE/i -
Gigasense
The PIAB LKVE electronic overload protection system consists of a force transmitter with amplifier and an electronic signal processing unit. The PIAB LKVE force transmitter is attached to a stationary line part. The rope is deflected via a slight angle between the two wheels and the clamping jaw. When loaded, the rope tends to straighten and applies a force which is transmitted to the load cell. The load cell in the PIAB LKVE delivers a signal proportional to the force on the load cell. The signal is amplified and is converted to 4-20mA. This standardized signal (4-20mA) allows distances between the force transmitter and the electronic unit to be 500 m.
-
2975AR -
Novatech Instruments , Inc.
The 2975AR contains a rubidium timebase and provide one 10 MHz, one 5 MHz and one Signal Generator output. The Signal Generator uses Direct Digital Synthesizer (DDS) technology and is programmable from 100Hz to 50 MHz using front panel controls or from an RS232 serial interface. The 2975AR can be disciplined by a 1pps input signal and provides a 1pps output signal. The 1pps input is typically provided by the GPS Frequency output from a device like a smart GPS receiver or antenna. The Novatech GPS1 Smart Antenna is available as an accessory to provide a complete turnkey solution.
-
Tektronix, Inc.
Verification and debug of today's high speed, low voltage digital signals requires probing solutions that can accurately acquire from a wide variety of electronic designs and protect signal fidelity. Tektronix logic analyzer probes contain a variety of connectivity options that are engineered to ensure that signal acquisition is a true reflection of your design's performance. Compare and learn more about Tektronix logic analyzer probe solutions.
-
VCH-1008 -
VREMYA-CH JS Company
The VCH-1008 Passive Hydrogen Maser is a compact hydrogen maser with excellent frequency stability and utilises state-of-the-art technology. Full digital processing of the modulation and servo loop signals makes it ideal for high accuracy applications. An internal GPS/GLONASS option is available and provides automatic output signal frequency calibration.Key applications:- National Time Keeping Service- Space tracking and navigation- Verification of frequency signals - Scientific research
-
D240X -
Pettersson Elektronik AB
Very popular heterodyne and time expansion detector with backlit, large digit, accurate digital display, showing the tuned frequency in the heterodyne mode. The frequency and volume controls are on the side of the case, making it easy to adjust. Using stereo headphones, the heterodyne signal is heard on the left channel and the time expansion signal on the right channel. When the built-in speaker is used, a switch is used to select the heterodyne or time expansion signal.