Showing results: 2941 - 2955 of 8202 items found.
-
Ironwood Electronics
For BGA, QFN, or LGA applications, GTP contact technology provides >94 GHz signal speed and can additionally be used in high cycle life applications such as ATE. These sockets support pitches from 0.2 mm to 1.27 mm. Ironwood's GT sockets are ideal for prototyping and testing almost any BGA device application. These IC sockets provide excellent signal integrity yet remain cost effective. Innovative elastomer interconnect technology that delivers low signal loss (1dB at 94GHz) and supports BGA packages with pitches down to 0.2mm was utilized in these sockets. GT BGA sockets are mechanically mounted over a target system's BGA lands using mounting and alignment holes at proper locations (page 2 of the individual socket drawing shows recommended PCB layout information). These low-profile sockets are only 2.5 mm per side larger than actual IC packages (industry's smallest footprint).
-
34905A -
Keysight Technologies
The Keysight 34905A RF multiplexer module for the 34970A/34972A Data Acquisition/Switch Unit offers broadband switching capabilities for high-frequency and pulsed signals. Use it to route test signals between your device under test and your signal generator, oscilloscope, spectrum analyzer, or other instrumentation.
-
MS 1303 -
Meltronics Systemtech
The Railway signaling unit is used to receive the input signals from the field for validating and clearing route for trains. After receiving the signals, signals are isolated and various tests are done inside the system to ensure the received signals reliability and produce clearance signal to railway line. For security reasons card signature has been given to each card in the system. System consists of digital input modules, digital output module, digital read back module, RS232 interface with 80486 processor board. It is an ISA Bus Back plane based system.
-
Mornsun Guangzhou Science & Technology
An isolation amplifier is an amplifier that provides isolation between the input and output of the circuits, including isolation between their associated power supplies. MORNSUN offers different types of analog isolation amplifiers, such as acquisition type signal conditioning modules, output isolation signal conditioning modules, two-wire loop power supply signal conditioning modules and signal isolators, etc. These analog isolation amplifiers feature excellent temperature drift characteristics of less than 50PPM/℃ across the entire operating temperature range of -40 ℃ to +85 ℃ and achieve isolation transmission, signal conversion (programmable for some models), HART communication, signal amplification, port protection and other functions. SIP, DIP, SMD and DIN Rail packages are optional.
-
ZET 7120 -
ZETLAB Company
The ZET 7120 unit converts signal from the sensor into temperature values. The resulting temperature values are transmitted via CAN interface. Thus, the use of digital sensors releases the user from the necessity of the measuring channels setting.
-
DD-1 -
D'Amore Engineering llc
The purpose of this tool is to enable the installer to set the gain of an audio amplifier to match the source unit's output level, accurately and quickly. It can also be useful for detecting distortion in the audio signal caused by poorly designed or malfunctioning audio equipment.
-
BEI Industrial Encoders
BEI Sensors offers a variety of electronic interface and converter modules for encoders. These modules can help solve a multitude of interface issues including mismatched data voltages, incorrect output types, incorrect resolution, or poor signal compatibility.
-
FRF -
Crystal instruments
FFT Spectral Analysis. Frequency Response Function (FRF) is a commonly used measurement type of the Dynamic Signal Analyzer. FRF is defined as the ratio of response i.e. acceleration, velocity, or displacement with respect to the excitation force which is the reference.
-
Newport Electronics
High speed optical detectors use special photodiodes with high speed electronic circuits to convert fast optical pulses to electrical signals for measurement. Unlike our optical receivers, these detectors do not include a transimpedance amplifier.
-
OLS -
Holding Informtest
The OLS module is a specialized device for input-output of logical information, intended for the formation and registration of asymmetrical logical levels of signals on 64 channels. The OLS module is made in the VXI standard and is functionally close to the DI-Series modules from Teradyne.
-
FSE-100 -
Walsn Enterprises Ltd.
FSE-100 Explosion-proof Flame Detector is used to collect the flame signal which is amplified and processed to determine the presence or absence of flame. FS-100 Flame Detector provides the flame output in real-time – the basis of determining the presence or absence of flame.
-
40-965-901 -
Pickering Interfaces Ltd.
Low cost converter card for 40-736 Data Communications Multiplexer. Adapts the 78-Pin D-type connector on the front of the module to 9 RJ45 sockets. Allows the multiplexing of up to 8 Ethernet signals with speeds up to 1G bit.
-
ifm efector, inc.
*Capacitive sensors for position detection or level monitoring*Distance sensors with very long range and background suppression*Ultrasonic sensors for non-contact detection of objects*Photoelectric sensors for specific applications*With switching output, analog signal and IO-Link
-
Abaco Systems Inc
Utilizes our Board Support Packages to get your hardware implementation underway as quickly as possible. The BSP gives you the control, flexibility and power to develop solutions for your most demanding digital signal processing applications.
-
PCIe-IDIO-24 -
Acces I/O Products, Inc.
This product is a x1 lane PCIe isolated digital input and FET output board with Change of State (COS) detection capabilities. In addition to the isolated signals, 8 (or 4) TTL/CMOS input/output pins are available, for your application’s convenience.