Showing results: 3421 - 3435 of 8202 items found.
-
Test Equipment Connection
A network analyzer is an instrument used to analyze the properties of electrical networks, especially those properties associated with the reflection and transmission of electrical signals known as scattering parameters (S-parameters). Network analyzers are used mostly at high frequencies; operating frequencies can range from 9 kHz to 110 GHz
-
GAO Tek Inc.
Optical fiber identifiers from GAOTek are ruggedly built and easy to use. Using this instrument, detect the presence of signals on optical fibers. For field technicians, fiber identifiers are an important tool. Instantly verify whether live fibers are connected or disconnected, and trace fibers from end to end.
-
Optilab, LLC.
A high sensitivity receiver in a fiber pigtail coupled package, it includes a high speed InGaAs avalanche photodiode with a high gain TIA in a hermetically sealed coaxial package. It incorporates an LC/UPC pigtail and a flexible printed circuit (FPC). The signal GND and a receptacle are electrically isolated in this APD receiver.
-
SY020 -
Synectic Electronics
The SY020 Pulse Rate Converter can be linked to any frequency generating device e.g. flow meters, which gives TTL, pulse Reed switch or coil output, converting the frequency to an analogue signal. This can be 4-20mA loop current or a voltage output. The 4-20mA version unit is loop powered.
-
40-657A-001-8/8/1 -
Pickering Interfaces Ltd.
The 40-657A-001-8/8/1 is a 8-bank, 8-channel, 1-pole MUX and is part of our range of High Density 2 Amp Power Multiplexer Modules available in a choice of configurations, containing up to 8 separate multiplexers, all 1-pole switching. They are suitable for switching signals to 110VDC/250VAC at 2Amps, 90W.
-
40-657A-001-1/64/1 -
Pickering Interfaces Ltd.
The 40-657A-001-1/64/1 is a 1-bank, 64-channel, 1-pole MUX and is part of our range of High Density 2 Amp Power Multiplexer Modules available in a choice of configurations, containing up to 8 separate multiplexers, all 1-pole switching. They are suitable for switching signals to 110VDC/250VAC at 2Amps, 90W.
-
SIM914 -
Stanford Research Systems, Inc.
The SIM914 350 MHz Preamplifier contains two wide-bandwidth, DC-coupled amplifiers, each with a gain of 5 (14 dB). Its fast rise time, low noise and excellent DC accuracy make it an ideal instrument for amplifying signals like those from photomultiplier tubes and photodiodes.
-
4320 -
Technobox, Inc.
Basic CMC Extender for PrPMC, PMC, and PMC-X. The Basic Common Mezzanine Card (CMC) extender provides a means to extend IEEE 1386 boards for signal accessibility. PrPMC (VITA 32), PMC (IEEE 1386.1), PMC-X (VITA 39) and any other CMC-derived board is supported.
-
Reach Technologies Inc.
Reach Technologies' CAN Logger is a high performance, high channel count, DSP enabled, automotive bus data logger. The CAN Logger is ideal for capturing all or specific bus traffic for vehicles under test. The CAN Logger is also perfect for real-time monitoring of specific signals.
-
40-657A-001-4/16/1 -
Pickering Interfaces Ltd.
The 40-657A-001-4/16/1 is a 4-bank, 16-channel, 1-pole MUX and is part of our range of High Density 2 Amp Power Multiplexer Modules available in a choice of configurations, containing up to 8 separate multiplexers, all 1-pole switching. They are suitable for switching signals to 110VDC/250VAC at 2Amps, 90W.
-
40-657A-001-2/32/1 -
Pickering Interfaces Ltd.
The 40-657A-001-2/32/1 is a 2-bank, 32-channel, 1-pole MUX and is part of our range of High Density 2 Amp Power Multiplexer Modules available in a choice of configurations, containing up to 8 separate multiplexers, all 1-pole switching. They are suitable for switching signals to 110VDC/250VAC at 2Amps, 90W.
-
Model 4060 -
Teledyne Analytical Instruments
The 4060 Series speciates gases of interest by combining well-accepted gas chromatography techniques with field-proven detector technologies. This combination, along with effective electrometer-based signal amplification and temperature controls, enables the series to detect either single or multiple compounds in a background gas possessing potentially interfering compounds.
-
B-1022 -
ROSS ENGINEERING CORPORATION
AC QuietDC to 800HzClass B and H insulationExtendable strokeUniversal mountingHigher holding forceEnvironment resistantOptional electronic controller* *Allows vibration free operation *Prevents coil burn-out *Provides DC-800Hz capability without heat producing dropping resistors *Optional Computer Controlled with 4-10V 5mA signal
-
T20 -
SONOTEC GmbH
The structure-borne ultrasonic probe T20 is used for condition monitoring of machines, systems and processes, given that they generate detectable structure-borne sound in the ultrasonic range. Changes in the sound signals indicate a change in the condition and/or process of the plant. The detection of these changes forms the basis for condition monitoring in predictive maintenance.
-
JTAG Starter Kit -
Corelis, Inc.
The Corelis JTAG Starter Kit includes the ScanExpress Debugger software application with a USB 2.0 JTAG controller. Engineers and technicians alike can use the system for a variety of tasks. The JTAG Starter Kit has an arsenal of features to control and observe system signals of a boundary scan compatible UUT.