Showing results: 7036 - 7050 of 8202 items found.
-
781098-02 -
NI
100 kS/s/ch Simultaneous, ±10 V, Isolated, 4-Channel C Series Voltage Output Module - The NI‑9269 is a channel‑to‑channel isolated analog output module. The NI‑9269 adds channel‑to‑channel isolation for increased safety and improved signal quality. Channel‑to‑channel isolation is commonly needed for applications that have multiple electrical systems, such as automotive tests, or industrial applications that are subjected to increased noise and often contain multiple ground planes.
-
781909-01 -
NI
20 MHz Bandwidth, 400 MHz to 4.4 GHz Software Defined Radio Device - The USRP‑2922 is a tunable RF transceiver with a high-speed analog‑to‑digital converter and digital‑to‑analog converter for streaming baseband I and Q signals to a host PC over 1 Gigabit Ethernet. You can also use the USRP‑2922 for the following communications applications: WiFi, WiMax, S‑band transceivers, and 2.4 GHz industrial, scientific, and medical (ISM) band transceivers.
-
779063-01 -
NI
8 AI (16-Bit, 250 kS/s/ch), 8 DIO, PXI Multifunction I/O Module—The PXI‑6143 is a simultaneous-sampling, multifunction data acquisition device. It offers analog input, digital I/O, two 24‑bit counters, and digital triggering. The PXI‑6143 is ideal for a variety of applications, such as high-energy physics, ultrasonic and sonar testing, ballistics and highly transient signals, and multiaxis control. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
HS801-AWG -
TEAM SOLUTIONS, INC.
The HS801: the first 100 MSPS measuring instrument that consists of an Arbitrary Waveform Generator/Function Generator, a Voltmeter, a Digital Storage Oscilloscope (DSO), a Spectrum analyzer, and a Transient Recorder. This new portable and compact measuring instrument can solve almost every measurement problem. Analyzing signals is done with 8-bit resolution and a maximum sampling speed of 100 MHz. The input range is 0.1 Volt full scale to 80 Volt full scale. The record length is 32K/64K samples.
-
CloudSDR -
RFSPACE, Inc.
The CloudSDR''s remote mode also offers a variable width spectrum analyzer with adjustable spans up to 10 MHz wide. The spectrum information update rate can be adjusted up to 10 Hz or turned off to limit the bandwidth utilization. In addition, the built-in squelch can be used to limit data transmission when no signals are present. Wideband spectrum analyzer mode offers 56 MHz wide spectral captures in both 2D, 3D and waterfall formats.
-
Rohde & Schwarz GmbH & Co. KG
The phase noise analyzer portfolio from Rohde & Schwarz offers an affordable, mid-range solution with high sensitivity and fast measurements as well as high-end ultra-high-sensitivity solutions with advanced measurements modes. Ideal for phase noise analysis and VCO tests, the industry-leading solutions enable two-path phase noise analysis with real-time cross correlation and fast VCO characterization with built-in low-noise DC sources. Additionally, high-end signal and spectrum analysis can be added into a single box.
-
Keysight Technologies
Measure with confidence from 4 to 50 GHz - precise measurements agree with benchtop resultsCapture every signal with real-time spectrum analysis (RTSA) up to 50 GHzWithstands your toughest working environments - rugged enough to meet MIL-specsWeighs less than alternative solutions- millimeter-wave models 30% lighter than other handheldsChoose to configure as a cable and antenna analyzers (CAT), vector network analyzers (VNA), spectrum analyzers and all-in-one combination analyzer
-
N9912C -
Keysight Technologies
Select from cable and antenna analyzer (CAT), Vector Network Analyzer (VNA), and/or Spectrum Analyzer with desired maximum frequency. Capture elusive signals with up to 40 MHz gap-free, real-time bandwidth. Measure all four S-parameters simultaneously with 115 dB dynamic range. Make accurate spectrum analyzer measurements (± 0.3 dB) without warmup. Perform over-the-air measurements for 5G NR and LTE. Use GPS/GNSS for geolocation and timestamping.
-
MS 1527 -
Meltronics Systemtech
The Semi-ATE is used for testing the analog ADC. It shall carry out the functional test on ADC analog module. The ATE shall have all necessary IO signals on the connector end. The semi-ATE can carry out the functional tests on ADC analog module with host PC or laptop. It provides +15V, -15V, +5V & -5V to module and +2.5V high precision reference voltage. It can able to control keysight N6700B Power supply mainframe using RS422 interface.
-
Optoplex Corporation
Optoplex’s MEMS Tunable Optical Filter is based on a patented micro-optic design with MEMS tuning technology. It is an integrated module consisting of a MEMS chip, micro-optics and control electronics and interface. When receiving a stream of optical signals of a plurality of wavelengths from the Input-Port (IN), the 2-port tunable optical filter directs a selected channel to the Output-Port (OUT). Wavelength (frequency) tuning is achieved by changing driving voltage applied to the MEMS chip, via the control electronics and the built-in firmware.
-
Cleverscope Ltd.
Power Amplifier is used to amplify the output of the CS700A or CS701 signal generators. The 52 MHz bandwidth amplifier can swing 36Vpp with an output current up to 1A continuous. The CS1070 includes an internal inverting power supply to provide the negative rail, simplifying power supply requirements. The gain is fixed at x10 (20dB). The output voltage range is ±5V to ±18V and asymmetrical to +31, -5V for PSRR measurements right up to 30V as the input supply increases past 20V.
-
Cleverscope Ltd.
Cleverscope Windows Application Software. Note we have added the Frequency Response Analyser (FRA) and Streaming capability to our Cleverscope application and so now it is available with all variants of our products, including units you have already bought. For power supply and power plane measurements you do need the isolated CS701 signal generator.We also now have the CS448 with four 1kV isolated channels with CMRR > 100 dB at 50 MHz.
-
865684-01 -
NI
NI-9215, cDAQ-9171, and NI-9981 USB Voltage Measurement Bundle - The USB Voltage Measurement Bundle with NI-9215, cDAQ-9171, and NI-9981 includes the NI-9215 C Series Voltage Input Module and the cDAQ-9171 CompactDAQ Chassis for voltage measurements. This bundle also includes the NI-9981 Connector for strain relief and operator protection from high-voltage signals. The included NI-9215 provides noise immunity, a high common-mode voltage range, NIST-traceable calibration, differential analog inputs, and four channels.
-
LadyBug Technologies LLC
LadyBug True RMS Average Power Sensors deliver reliable, accurate power measurements for CW, Pulse, and modulated signals. These diode based sensors feature a wide dynamic range and a great VSWR. The optional external triggering input feature can be used without any external components. Recorder and Trigger outputs are also available. Our patented NoZero NoCal technology make these sensors ideal for calibration systems, automated test stations and other embedded applications.
-
Integra Technologies
Integra provides extensive experience with complex test development: Digital & Mixed Signal Devices: Microprocessor, Microcontrollers DSP, ASIC. Linear: DAC, ADC, Operational Amplifier, Comparator, Multiplexer, Interface, Discrete. Memory: SDRAM, DDR, SRAM, SSRAM, Flash, EEPROM, EPROM. Logic: 74xxx, 16/32-bit, ECL. RF, 8GHz typical and experience to 50GHz: PA, LNA, Filter, Mixer. Expertise in developing test plans (semi mfgr production & device characterization)