Showing results: 7306 - 7320 of 8202 items found.
-
DTX-6017SSC/HV -
R.C. Electronics, Inc.
The DTX-6017SSC/HV series of data acquisition systems provide wideband, low noise sensor signal conditioning with embedded filtering, digitization and data recording direct to 4GB of SDRAM locate on each DTX-6192 module. System level recording rates are no longer limited by chassis throughput, bus bandwidths or long term disk storage speeds. A comprehensive user GUI running on the embedded Windows OS can be used locally with the addition of a user keyboard, mouse and video terminal, or run remotely via the integrated Ethernet connection.
-
Ahloborn
A wide range of probes, sensors and signals is available for ALMEMO® data loggers and measuring instruments, which are connected via intelligent connectors with integrated data carrier. For common measuring tasks the connectors are configured at the factory and the measuring device automatically recognizes the connected sensor. All sensors can be calibrated, scaled and provided with a unique designation via the intelligent connectors. The programming always remains with the corresponding sensor, so that it can be connected to any input on the measuring instrument. Inaccuracies of a sensor can be corrected in the connector, thus turning simple sensors into precise transducers.
-
CD23/223 -
Validyne Engineering
The CD23 and CD223 Digital Transducer Indicators are designed for use with variable reluctance and differential transformer transducers. The CD23 accepts input from a single transducer, and the CD223 accepts two switch-selectable inputs, with Zero and Span controls for each input. The indicators provide 5 Vrms, 5 kHz carrier excitation voltage to the transducer(s) and solid state circuitry to amplify, demodulate and filter the transducer output signals. A 3 1/2 digit front panel display is standard, with a 4 1/2 digit display optionally available.
-
BC 1313 TRIAXIAL SEISMOGRAPH -
ZETLAB Company
BC 1313 piezoelectric seismographs are intended to convert vibration parameters to a proportional electrical signal. Measurements are carried out for 3 mutually perpendicular axes X, Y, and Z at a time. BC 1313 seismographs are seismic accelerometers, the parameter measured – vibration acceleration. For BC 1313 seismic transducers, the system is provided for sensing element electrical stimulation using an actuator to determine conversion ratio true value during periodic recalibration without dismantling. Power check system is also allowed for in BC 1313 seismographs.
-
Antenna Research Associates
Vehicular and Handheld antennas are available for communication, surveillance, signal DF, network repeaters and RF Jamming applications. A single omni or high gain directional ARA antenna may cover all cellular and/or Tetra communication bands and are compatible with all network technologies (GSM, CDMA, etc.). These wideband antennas replace the need for several single band antennas and are ideal for vehicular installations as well as handheld radio mounted applications. Permanent installations, quick deploy magnetic mounts or convenient pistol grips for radio location are available.
-
60-983-002 -
Pickering Interfaces Ltd.
The 60-983 is an LXI compatible Wired Trigger Bus Terminator (WTB) designed to be attached to the end of a WTB cable. The LXI WTB uses a transmission line cable to connect LXI devices together that support the WTB capability of the LXI standard. Like all transmissions it needs to be correctly terminated to avoid reflections that could change the signal amplitude along the cable and generate timing jitter or trigger errors. The 60-983 is a simple terminator that can be placed at each end of the WTB chain to correctly terminate the transmission line with minimal reflections.
-
60-983-003 -
Pickering Interfaces Ltd.
The 60-983 is an LXI compatible Wired Trigger Bus Terminator (WTB) designed to be attached to the end of a WTB cable. The LXI WTB uses a transmission line cable to connect LXI devices together that support the WTB capability of the LXI standard. Like all transmissions it needs to be correctly terminated to avoid reflections that could change the signal amplitude along the cable and generate timing jitter or trigger errors. The 60-983 is a simple terminator that can be placed at each end of the WTB chain to correctly terminate the transmission line with minimal reflections.
-
60-983-001 -
Pickering Interfaces Ltd.
The 60-983 is an LXI compatible Wired Trigger Bus Terminator (WTB) designed to be attached to the end of a WTB cable. The LXI WTB uses a transmission line cable to connect LXI devices together that support the WTB capability of the LXI standard. Like all transmissions it needs to be correctly terminated to avoid reflections that could change the signal amplitude along the cable and generate timing jitter or trigger errors. The 60-983 is a simple terminator that can be placed at each end of the WTB chain to correctly terminate the transmission line with minimal reflections.
-
Bourns
A rotary position sensor translates angular mechanical position to an electrical signal. Rotary position sensors are designed for applications that typically require frequent adjustment. Shaftless designs allow for different engagement mechanisms, such as a customized shaft, a motor control, a human interface adjustment or a mechanical arm position locator. Rotary position sensors can be used in applications where a user needs to control a variable output such as a frequency, speed or volume control. Typical applications include test and measurement equipment, consumer electronics, small engines, robotics, and medical equipment.
-
TH2512 -
Shenzhen Chuangxin Instruments Co., Ltd.
The TH2512 series digital dc low resistance tester i s an intelligent, wide range, high-precision tester which suitable for transformer, inductor copper resistance, relay contact resistance, switches, connectors, wire resistance, contact resistance component solder contact resistance, PCB line, welding hole resistance and metal detection, etc. It’s applied to the production line and can use HANDLER interface and GPIB interface (option) output good/bad signal, in order to improve production line automation testing capability.
-
Z-Boat 1250 -
Teledyne Marine Oceanscience
Teledyne Oceanscience Z-Boats® are the number one choice for reliable, remotely controlled, hydrographic surveying in streams, rivers, lakes, and coastal waters around the world.Whether you need to reduce survey time, keep people safe during hazardous conditions, or access hard to reach locations, there is a Z-Boat to suit your survey and your budget. The Z-Boat 1250 is easy to operate. The integrated echosounder has an embedded transceiver with digital signal processing and outputs depth & temperature using NMEA 0183 data output.
-
T3PP350A -
Teledyne LeCroy
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.
-
T3PP350 -
Teledyne LeCroy
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.
-
PP006D -
Teledyne LeCroy
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.
-
PP005A -
Teledyne LeCroy
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MO. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.
