Showing results: 1366 - 1380 of 8202 items found.
-
SARP-6 -
Saluki Technology Inc.
Saluki SARP-6 RF Signal Acquisition Record and Playback Apparatus is a portable RF signal acquisition record playback equipment. It can be used to directly acquire, record, and playback RF signal from 1MHz to 6GHz. Its data recording and bandwidth playback can reach 200MHz. The SARP-6 RF Signal Acquisition Record and Playback system is composed of up and down inverter module, high-performance ADC and DAC, and large capacity solid-state FLASH or high-performance disk. It is widely used in radar, GPS, communication, telemetry, as well as many other circumstances for civil purposes when acquiring signal and recording it down.Applications: Interference Analysis/Surveillance/Spectrum Management/Satellite Communications
-
CAST Navigation
CAST Navigation’s GNSS simulation systems produce GNSS RF signals that provide a precise and repeatable testing signal, perfect for use either in the field or in the laboratory environment. These systems can be used for a wide range of testing and integration verification applications and they are an ideal choice for stimulating military or commercial devices where only GNSS signals are needed. Our simulators are powered by proprietary multi-frequency, multi-constellation GNSS RF signal generation technology. This technology provides you with highly accurate and fully programmable signals along with advanced vehicle trajectory capabilities allowing you to custom tailor parameters and trajectories to meet your simulation requirements.
-
SPC - INS - 1010 -
Signals & Systems India Private Limited
The IRIG-B TTL signal is a time synchronization protocol that can be transmitted up to 50m maximum using coaxial cable. So the relay which is to be received the IRIG-B TTL signal may be far away from the IRIG-B source. The relay may be not able to synchronize with the GPS. To avoid such an incident in the field, some of the relays have provision to receive IRIG-B RS485 signal. The IRIG-B RS485 signal can able travel up to 1200m without any booster. All Time source equipment may not be supplied with IRIG-B RS485 signal output. The converter will act as a bridge between GPS Time source and Relays for time synchronization.
-
MAX98357A -
SparkFun Electronics
The SparkFun I2S Audio Breakout board uses the MAX98357A digital to analog converter (DAC), which converts I2S (not be confused with I2C) audio to an analog signal to drive speakers. The I2S Audio Breakout converts the digital audio signals using the I2S standard to an analog signal and amplifies the signal using a class D amplifier which can deliver up to 3.2W of power into a 4Ω load. The board can be configured to output only the left channel audio, right channel, or both.
-
Shoghi Communications Ltd.
Radio Reconnaissance and Jamming Station is monitoring and jamming of radio signals in the frequency range of 25 to 1000MHz. The Radio Reconnaissance and Jamming Station allows audio monitoring, technical analysis, monopulse bearing finding of the radio emission sources.The Radio Reconnaissance and Jamming Station is capable of scanning the VHF/UHF frequency bands to identify the various sources of radio transmissions with their signal parameters. Carry out direction finding (DF) of the source of the radio signals and generation of jamming signals of required waveform to carry out jamming.
-
Tracy -
BAUR Prüf- und Messtechnik GmbH
Cable testing and diagnostics with the BAUR tracy. The BAUR tracy partial discharge inductor induces a signal at the apparent fault location in the cable from outside. In combination with any PD measurement system, e.g., PHG TD/PD, the induced signal can be located and compared with the result of the partial discharge pre-location. The partial discharge location can thus be determined precisely.* Portable, battery-operated signal coupling device* Suitable for cables and cable accessories* Inductive signal coupling* Aviods costly, unnecessary replacements of PD-free cable accessories
-
Picoprobe
The PICOPROBE® DUAL MICROWAVE PROBE consists of two separate probes mounted on a single holder. One probe is fixed to the holder; the other is adjustable. Each probe may be individually configured with GSG, GS, or SG footprints having any fixed pitch from 50 to 2540 microns. The probe to probe (signal to signal) spacing is user adjustable over a 4000 micron (160 mil) range. When ordering, an initial signal to signal spacing should be specified (up to .75 inches).
-
Kemo
After many years supplying high qaulity signal conditioning instruments we understand the need to use high quality cable connectors & adaptors. The connectors used by Kemo on its cable assemblies are fitted by engineers with years of experience. This attention to detail ensures quality signal transmission and minmial noise within the signal path.
-
SINAD -
ComTekk Engineering, LLC.
SINAD utilizes the latest in Digital Signal Processing (DSP) technology to accurately measure several key performance characteristics of radio receivers by analyzing the spectral content of a received audio signal.
-
DekTec Digital Video B.V.
SMPTE-2022 compliant standalone solutions for conversion between IP and "traditional" DTV signals such as ASI and QAM. These IP converters are hardware-based, providing low latency and zero-jitter transmission of IP signals.
-
DATS Software -
Prosig Ltd
DATS is a comprehensive package of data acquisition, signal processing and reporting tools. It is used mainly for noise and vibration analysis, but can be used for a wide range of engineering and general signal processing tasks.
-
Microwave Factory Co,Ltd.
Shield room is the equipment to shut-out the electric/magnetic wave signals from outside and not to leak the electric/magnetic wave signals from inside. We can support as custmized request on room/box size, performance.
-
Virginia Panel Corporation
VTAC patchcords are renowned for their signal integrity and speed. VTAC’s ground-signal scheme, precision-welding, and hermaphroditic connector designs help to reduce signal degradation even in the most demanding test environments.
-
P8552 -
COMET SYSTEM, s.r.o.
The devices are equipped with two connectors for connection of the temperature and humidity external probes and three binary inputs for two-states signals. The dry contact or two-state voltage signal can be connect to the binary input.
-
MCR9000 -
Matrix Technology Inc.
MCR-9000 Series is a high precision impedance analyzer with DC 10Hz-30MHz frequency and 10 mV-2Vrms (min. resolution 1mV) test signals, and is suitable for the LCR and DCR tests of AC signals.