Showing results: 3001 - 3015 of 6648 items found.
-
Weiss Technik North America
Weiss Technik Thermal Shock chambers are designed to give quick transitions between a HOT and COLD temperature zones. Available in vertical, horizontal and liquid models. Thermal stock chambers are used in all industries including Automotive, Electronics, Aerospace, and others to help find product defects in electronic components and product assemblies. Thermal shock is important with MIL -STD 883 test standard.
-
CSS61000-11 -
Lisun Electronics Inc.
The voltage dip and interruptions generator is specially designed according to the characteristics and requirements of EMS measurement under a sudden reduction or interruption of the voltage at a point, CSS61000-11/ CSS61000-11T used a big LCD in both English and Chinese operating interface. They have more fine performance such as high reliability, convenient operation, and full meet the standard requirements of IEC 61000-4-11, EN 61000-4-11 and GB/T17626.11
-
SKS-IV10J -
Shanghai Sanki Electronic Industries Co., Ltd.
The voltage pulse generator SKS-IV10J is completely designed in accordance with the requirements of the impulse voltage chapter in OIML R 46-1/-2; it meets the requirements of the new IEC60255-5 and GB14711 standards; the leakage current detection alarm function is added, and the leakage current limit can be Adjustment; using linearized high-voltage power supply, low noise, high stability, high voltage accuracy and long service life.
-
WATOM -
KoCoS Messtechnik AG
WATOM can carry out fully automatic, non-contact measurements of the edge profiles and diameter in accordance with SEMICON standards. A special feature is the system's ability to make measurements of the mark cut into the edge of the wafer to indicate the crystal orientation. Because of its high measurement accuracy of less than 1.5 µm, leading wafer manufacturers across the world use WATOM for shop-floor geometrical quality control.
-
Meriam Process Technologies
Manometers have many advantages in this age of technology because of their inherent accuracy and simplicity. Manometers are unique in being both pressure measurement instruments and standards for calibration of other instruments. The manometer is commonly used to measure pressures ranging from as high as 100 inches of 2.95 Red Fluid (10.65 PSI) to the lowest vacuums of space. Manometers are available in varying designs depending upon application:
-
CPCI395 -
AcQ Inducom
The CPCI395 features 16 analog voltage outputs, integrated on the CompactPCI standard. Each output has a 12- or 16-bit resolution and a software programmable output range (0..+10V or -10..+10V). Control of the analog output is as easy as writing the binary equivalent to a dedicated register (per channel). Conversion takes place automatically. If desired, channels can be synchronized by presetting the channels and then give a simultaneous update command.
-
FMC160 -
Sundance Multiprocessor Technology Ltd.
The FMC160 provides one 12-bit A/D channel at 3.6Gsps and one 14-bit D/A channel at 5.6Gsps (2.8Gsps direct RF synthesis) clocked by either an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. In addition, a trigger input for customized sampling control is available to users. The FMC160 daughter card is mechanically and electrically compliant to the FMC standard (ANSI/VITA 57.1).
-
SIM-2PRI-PCI -
Virtual Console, LLC
The most inexpensive ISDN PRI simulator on the market. Designed in standard PCI card form factor it has two PRI(T1 or E1) ports allowing ISDN PRI equipment to be connected together just as if they were connected through the ISDN network. Simulator card does not require any OS drivers, completely software independent and it take only power from the host computer.
-
Axiomtek Co., Ltd.
The 3.5" embedded board is created in an architecture of low power consumption with reliability required for various applications in rugged environments. The ZIO form factor is an integrated interface standard defined by Axiomtek and has been adopted as one of our specifications in our 3.5" embedded single board computers to meet concerns regarding insufficient expansion interfaces in small form factor (SFF) single board computers.
-
VPX6-195 -
Curtiss-Wright Defense Solutions
Our VPX6-195 6U OpenVPX T2080 Single Board Computer (SBC) combines performance with the advanced I/O capabilities of the NXP's quad-core AltiVec enabled T2080 processor. Designed for SWaP-constrained applications, the VPX6-195 provides two independent processor cores on a single printed wiring board (PWB) with a wide range of standard I/O and each with a XMC mezzanine site to provide twice the processing power.
-
XCVR-AS5653 -
Avionics Interface Technologies
AS5653 SFP transceiver that can be inserted into any standard SFP slot - 1.0625 GBPS communication signals interface using TNC connectors - Bulkhead mountable female TNC connector at the end of a 1 meter length of RG179B/U - 100 feet of RG179 operates to better than 10E‐13 Bit Error Rate - Available for 75 Ohm single ended copper or 150 Ohm Differential
-
Quantic PMI
PMI offers a full line of RF and Microwave, Solid State Attenuators that range from a few MHz up to 40 GHz. While we offer many standard models, various options are available. If you do not see exactly what you require on this website, please contact sales@pmi-rf.com because we offer attenuators designed and built to your specifications at catalog prices.
-
T1000-62HD -
Tesuto Systems
Our most expansive breakout box, using dual High Density 62 pin D-Sub connectors for signal capture or monitoring. Dual connectors provide a total of 124 test points plus a ground jack. All test points use standard size 4mm banana jacks. Test points may be connected using shorting banana cable to allow signal continuity.
-
Mountz Inc.
Calibrated Dead Weight are the official means by which torque analyzers and torque sensors are calibrated and are traced to National or International Standards, such as N.I.S.T, ISO and others. Many industries like as medical, aerospace, nuclear and others continuously calibrate their measuring equipment to comply with government regulations. For companies that prefer to have calibration capabilities in-house when their calibration requirements become extensive, they need calibration equipment.
-
Active Silicon
Active Silicon offers camera interface boards for autofocus-zoom block cameras and adapters for host-end acquisition and video format conversion. The camera interface converter boards for Tamron AF-zoom cameras, Sony FCB block cameras, Harrier AF-zoom cameras and others, take data from the proprietary block camera interface and convert into industry standard formats such as 3G-SDI / HD-SDI, USB 3.0, HDMI and IP.