Showing results: 4321 - 4335 of 6646 items found.
-
IIB-1553-PC104 -
Western Avionics Ltd.
The IIB-1553-PC104 is an intelligent interface card providing full MIL-STD-1553 test, simulation and bus analysis capability for PC compatible computers, with 1553A, 1553B, McAir and STANAG 3838 variants in one card. The IIB-1553-PC104 supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with powerful multi-level triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides a single, dual redundant 1553 interface. 2 Mbytes of dual ported RAM are provided. PC memory space utilised by the board is selectable. The board is supplied with C drivers in source code and Windows menu driven software as standard
-
IIB-1553-PCI-2C -
Western Avionics Ltd.
The IIB-1553-PCI-2C provides an intelligent interface card for two serial, dual redundant MIL-STD-1553 data buses and the PCI bus. The card supports 1553A, 1553B, McAir and STANAG 3838 variants on a single card. The IIB-1553-PCI-2C provides concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with comprehensive multi-level triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. Two independent variable amplitude dual redundant 1553 interfaces are provided, each with2 Mbytes of dual ported RAM. The board is supplied with C drivers in source code and Windows menu driven software as standard.
-
IIB-1553-VXI-4C -
Western Avionics Ltd.
The IIB-1553-VXI-4C is an intelligent interface card which provides 4 independent channels for full MIL-STD-1553 test, simulation and bus analysis functions on the VXI bus. All 1553A, 1553B, McAir and STANAG 3838 variants are supported. Each independent channel may be operated as a concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with a windowed Bus Monitor (BM), or as a stand-alone Chronological Bus Monitor (CBM) with comprehensive multi-level triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. Each channel provides a variable amplitude dual redundant 1553 interface, with 2 Mbytes of dual ported RAM. The board is supplied with C drivers in source code and Windows menu driven software as standard.
-
Diamond SA
OTDR measuring devices are used in various ways in fibre optic technology. They enable extensive characterisation of existing fibre optic cabling networks. The use of launch and receive fibres is advantageous when it comes to ensuring precise results evaluations. With bidirectional backscatter measurements with launch and receive fibres, the attenuation values of the first and last plug-in connection can be determined precisely by averaging and device dead zones can be avoided. Measuring device manufacturers recommend different lengths of launch and receives fibres to avoid “phantom reflections”. These launch and receive fibres are also subject to measuring equipment monitoring and should regularly undergo revision in accordance with the OTDR measuring devices. A good measurement result depends on the state and quality of the measuring equipment used. Diamond offers various types of launch and receive fibres, one with standard telecommunications connectors and the other with an outdoor connector for harsh environments.
-
Focus Microwaves
All Focus tuners use extremely efficient calibration and tuning algorithms and control electronics based on LAN control (iTuner). This is a merger our proven tuner technology with state of the art control electronics to create the latest tuner generation. The on-board micro-processor and tuning firmware form a self-contained and fully calibrated test instrument. The micro-processor inside the tuner accepts ASCII format communication, via an industry standard TCP/IP interface, controls up to nine stepper motors (tuner axes) and executes interpolation and tuning functions for single probe (CCMT) tuners (one probe per frequency range). For tuners with more than one independent probe (MPT) covering the same frequency range to allow for harmonic tuning, external computing power is required, because of the exponentially growing number of combinations of tuner states (slug positions).
-
PCE Instruments
Here you will find a full range with an industrial standard noise dose meter to suit every requirement. With the portable noise dose meter you can carry out measurements quickly to gain control of a situation or to set the device to take timed measurements. The noise dose meter is important for all industries, especially by using it as a mobile device which is able to assess office stress levels or street noise levels.Often problems arise from noisy neighbors or if bars and restaurants are in residential areas and produce noise levels after 10pm in excess of what local laws permit. We, of course, can assess which noise dose meter you require in relation to the issue you have and the relating laws. We also have microphone extension cords, tripods, calibrators and calibration certificates for most models of noise dose meter.
-
PCI592 -
Vadatech Inc
The PCI592 is based on the Xilinx XCKU115 Kintex UltraScale FPGA, which provides 5,520 DSP slices, 75.9 Mb RAM and 1,451,000 logic cells. The FPGA interfaces directly to the FMC+ DP-23 and all FMC+ LA/HA/HB pairs, making it compatible with a wide range of industry standard VITA 57 modules. It also has interface to three DDR4 memory channels (2x 64-bit wide and 1x 32-bit wide). This allows for large buffer sizes to be stored during processing as well as for queuing the data to the host. The unit has x8 PCIe edge connector routed to the FPGA PCIe Gen3 hard IP block. In addition, 16 uncommitted connection pairs are routed to a dual x8 expansion connector, providing direct connectivity to a neighbouring FPGA (e.g. via Aurora, 10G/40G, SRIO, PCIe) without the need to go through the host.
-
PCI516 -
Vadatech Inc
The PCI516 is based on the Xilinx Virtex-7 690T, which provides 3,600 DSP slices, 52,920 Kb RAM and 690,000 logic cells. The FPGA interfaces directly to the FMC DP 0-9 and all FMC LA/HA/HB pairs, making it compatible with a wide range of industry standard VITA 57 modules. It also has interface to three DDR3 memory channels (64-bit wide and 16-bit wide). This allows for large buffer sizes to be stored during processing as well as for queuing the data to the host. The unit has x8 PCIe edge connector routed to the FPGA PCIe Gen3 hard IP block. In addition, 16 uncommitted connection pairs are routed to a dual x8 expansion connector, providing direct connectivity to a neighbouring FPGA (e.g. via Aurora, 10 G/40 G, SRIO, PCIe) without the need to go through the host.
-
PCI596 -
Vadatech Inc
The PCI596 is based on the Xilinx VU13P UltraScale+TM FPGA, which provides over 12,000 DSP slices, 360 Mb of UltraRAM and 3,780K logic cells. The FPGA interfaces directly to the FMC+ DP 0-31 and all FMC+ LA/HA/HB pairs, making it compatible with a wide range of industry standard VITA 57 and VITA 57.4 modules. It also has interface to DDR4 memory channels (1x 64-bit wide, 8 GB). This allows for large buffer sizes to be stored during processing as well as for queuing the data to the host. PCI596 has x16 PCIe edge connector routed to the FPGA PCIe Gen4 hard IP block. In addition, 16 uncommitted connection pairs are routed to a dual x8 expansion connector, providing direct connectivity to a neighbouring FPGA (e.g. via Aurora, 10/40GbE, SRIO, PCIe) without the need to go through the host.
-
ThermaStop-RT -
ThermaGenix Inc.
RNA oligonucleotides from cells and viruses can be amplified for detection using the methods of Reverse Transcription and Polymerase Chain Reaction (RT-PCR). In a first step, a complementary strand of DNA (cDNA) is synthesized using a primer and reverse transcriptase. The cDNA is then amplified using standard PCR techniques. This can be accomplished by taking an aliquot from the reverse transcription reaction and adding a DNA-dependent DNA polymerase (e.g. Taq) and other reagents and then doing PCR. That method is commonly called "Two-step RT-PCR", or "Two-tube RT-PCR". Alternatively, all reagents, including both enzymes and gene-specific primers can be included in a single tube in order to do both reverse trancription and PCR without the need to open the tube between those reactions. That method is commonly called "One-Step RT-PCR" or "One-Tube RT-PCR". Both methods can include primers for a single target or for multiple targets (i.e. multiplex RT-PCR).
-
National Technical Systems
According to the best meteorological estimates, the surface of the earth is struck by lightning approximately 100 times each second, which averages out to about 8 million strikes per day. In addition, the Federal Aviation Administration reports that the average commercial aircraft gets hit by lightning on average about once for every 1,000 hours of flight it completes, which amounts to approximately once a year.With statistics like these, it’s obvious that providing adequate lightning protection to electrical components is crucial — whether that’s onboard an aircraft or as part of a ground-based facility. Fortunately, at NTS, we’ve been helping companies do just that for well over 50 years. Thanks to our lightning simulation and modeling services, companies are able to develop high-quality products that meet with their respective compliance regulations — from military and defense to Airbus and Boeing published standards.
-
IIB-3910-CPCI -
Western Avionics Ltd.
The IIB-3910-CPCI is a single slot intelligent interface card providing complete STANAG 3838 and STANAG 3910 test, simulation and bus analysis capability for the CompactPCI Bus. The IIB-3910-CPCI supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with powerful multi-level triggering capability. Full error injection capability in both 3838 and 3910 modes is provided in BC and RTs modes, with full error detection in BC, RT, BM and CBM modes. Dual redundant 3838 interface, with user selectable dual redundant optical or single redundant electrical 3910 interface are featured. 2 Mbytes of dual ported RAM are provided. The board is supplied with C drivers in source code and Windows menu driven software as standard.
-
VQDM-100 -
VideoQ Inc
Versatile compact and robust multi-purpose tool for R&D and glass-to-glass QA/QC Instant visual-aural quality estimation plus automatic latency, AV sync and 3D LR sync measurement Multi-channel time-line analysis, including video frames continuity testing 4 Light Sensors with vacuum caps, 4 Audio inputs (standard line levels) 2 channels of AV timing analysis, simultaneous measurements of Video and Audio Latencies Real time multi-channel data acquisition via USB port Unique sophisticated set of static and dynamic test patterns up to 1080p@60fps - see more details in separate VQL page Source of VQDM, VQMA2, and VQMA3 Test Patterns for VideoQ Analyzers Multi-format digital and analog AV outputs: HDMI, YPrPb, S-video, SPDIF, LR analog audio Networkable unit, easy expansion with any external USB storage device: live clips, user content, etc.
-
CZ20154 -
Aegis Pty. Ltd.
The CZ20154 is the top of the range in latest design technology providing voice, data, and video technicians/engineers all the functionality essential in a test set. Buttinskis are now required to deal with modern high speed digital services - something this test phone has been specifically designed for. On top of all the tests performed by the CZ20123, TDR length measurement to 900m is included for the first time on a buttinski. Not only can you measure cable length but you can identify the fault location of an open or a short. Further, tone generation is included as standard providing 5 different search tones and SmartToneR that confirms you have located the correct pair. Never before has this level of features been available in a buttinski. No longer do you need to carry a separate butt set, TDR, toner, and identifier - this buttinski does it all in the one tool !
-
Model T703U -
Teledyne Advanced Pollution Instrumentation
The Model T703U is a microprocessor controlled ozone calibrator for precision gas analyzers. Expanded ozone audit levels have created a need for precise ozone calibration well below the capabilities of standard calibrators. The Model T703U is designed to meet the requirements of ultra-low ozone production.In addition to a high range with similar performance to the Model T703, the Model T703U has the capability to generate ozone in a low range, or "fractional" mode, for producing ozone levels down to 3 ppb, with exceptional accuracy. Flow rate and lamp intensity are adjusted to deliver a specified ozone concentration by volume. The temperature and pressure compensated photometer, identical to that of the Model T400 ozone analyzer, provides feedback control of the UV lamp intensity, assuring stable ozone output. A nearly unlimited number of calibration sequences may be programmed into the non-volatile memory of the T703U, covering time periods up to a year.
