Showing results: 4861 - 4875 of 6683 items found.
-
C.A 742 -
Chauvin Arnoux Metrix
The C.A 742 Voltage Absence Tester is an essential tool for any electrician to check that no voltage is present before working on an electrical installation connected to the network. It complies with IEC 61243-3 Edition 3 and can be used to work on any indoor or outdoor 600 V CAT IV installation. To fulfil the requirements of the standards and legislation in certain countries, there are 2 references, with or without IP2X accessories.
-
DPB8800 -
Applied Test Resources
The DPB8800 is an 11? x 14? PC board used to interface the tester with the Device Under Test (DUT). This board contains generous area for custom circuitry and extra relays. The DPB8800 is also available with standard solutions to test families of components like Op-Amps, Regulators, ADC?s and DAC?s. +/-15 V and +5 V are available to support circuitry biasing.
-
780321-01 -
NI
PXIe, 8-Slot, Up to 8 GB/s PXI Chassis—The PXIe‑1082 features a high-bandwidth backplane to meet a wide range of high-performance test and measurement application needs. It accepts PXI Express modules in every slot and supports standard PXI hybrid-compatible modules in up to four slots. The chassis features an extended operating temperature range for applications needing cooling performance.
-
Kontron
CompactPCI is a standard in computer bus technology for industrial computing that utilizes a Eurocard type connector combined with PCI signaling and protocols. cPCI boards come in 3U and 6U variants and are typically interconnected through a passive backplane. The connector pin assignments are standardized by PICMG , allowing for eight boards in a PCI segment with multiple bus segments being allowed with the use of active bridges.
-
PCIe-Mini-DA4 -
ALPHI Technology Corporation
The PCIe-Mini-DA4 is a PCiexpress Mini board with a total of 4 voltage outputs D/A. Each output is followed by a buffer able to provide +/- 30 mA. Special function code allows global updates of all channels or by a group of eight channels at atime. Standard ping-pong output registers for each channel or optional data RAM allows waveform generation with minimum processor involvement.
-
PCI-1553DDC-2 -
ALPHI Technology Corporation
The PCI-1553-DDC-1/2 implements a complete single channel dual-redundant MIL-STD-1553 bus terminal on a half size PCI Card. Full BC/MT/RT modes are supported. 0°C to 70°C operating temperature is standard. Included is an DDC Enhanced ACE intelligent communications protocol engine, dual transceivers and encoder / decoders, shared memory, and management logic.
-
K11644A -
Keysight Technologies
The Keysight K11644A calibration kit contains the precision mechanical standards required to calibrate the systematic errors of Keysight network analyzers. This calibration kit has a precision airline for performing the Thru-Reflect-Line (TRL) calibration, the most accurate error-correction technique for coaxial measurements. This kit also contains a commercial calibration certificate, flush short circuit, a precision shim, and fixed termination(s).
-
E36155AGVX -
Keysight Technologies
The Keysight E36155AGVX consists of a Keysight E36155A DC power supply, a Keysight E36150ADVU Scope View and arbitrary waveform generation (AWG) capabilities, and a Keysight E36150ATMU Automotive Standards Testing Capabilities with Enhanced Programming Speed, ISO Preset Library, Playback Simulation and E-Logging features. The E36155A includes single-output and auto-range capabilities, 60V, 40 A, 800 W, and LAN and USB interfaces.
-
Keysight Technologies
With Scienlab test systems and test software, Keysight offers customized test environments for the development and testing of electronic components according to hybrid and electric vehicle testing standards. Our solutions help you to accelerate your e-mobility applications from the battery, Battery Management System (BMS), inverter, the charging interfaces of Electric Vehicle (EV), and Electric Vehicle Supply Equipment (EVSE).
-
P11644A -
Keysight Technologies
The Keysight P11644A calibration kit contains the precision mechanical standards required to calibrate the systematic errors of Keysight network analyzers. This calibration kit has a precision airline for performing the thru-reflect-line (TRL) calibration, the most accurate error-correction technique for coaxial measurements. This kit also contains a commercial calibration certificate, flush short circuit, a precision shim, and fixed termination(s).
-
M9102A -
Keysight Technologies
The M9102A, a high-density, 128-channel multiplexer routes many different channels to a single point. The switches operate in a break-before-make mode that ensures no two points are connected at the same time. This 1-wire multiplexer features high speed, long-life reed relays capable of switching up to 100Vrms, with up to 10W of power. Connection options include the durable connector block or the standard cable connections.
-
PCIe-1553-uAce-1,2 -
ALPHI Technology Corporation
1or 2 controllers of dual redundant (A/B channel) 1553 communications• Programmable bus controller, remote terminal, or monitor terminal modes• MIL-STD-1553 A and B compliant, Notice 2 RT• STANAG 3838 bus compliant for NATO standard support• Long or short stub support • Low power consumption• PCIMG compliant• Single +5 VDC supply
-
E36154AGVX -
Keysight Technologies
The Keysight E36154AGVX consists of a Keysight E36154A DC power supply, a Keysight E36150ADVU Scope View and arbitrary waveform generation (AWG) capabilities, and a Keysight E36150ATMU Automotive Standards Testing Capabilities with Enhanced Programming Speed, ISO Preset Library, Playback Simulation and E-Logging features. The E36154A includes single-output and auto-range capabilities, 30V, 80 A, 800 W, and LAN and USB interfaces.
-
2720 ER -
Standard Electric Works Co., Ltd
● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● The test leads are supplied as standard accessories for simplified two-wire measuring system.● Battery operated.● Data hold function.● Battery test indication.● Calibration performed with supplied test leads.
-
1820 ER -
Standard Electric Works Co., Ltd
● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● The test leads are supplied as standard accessories for simplified two-wire measuring system.● Battery operated.● Data hold function.● Low battery indication.● Calibration performed with supplied test leads.