Showing results: 5866 - 5880 of 6648 items found.
-
ELMA Electronic, Inc.
Reliability and ruggedness are just two of Elma's core competencies for rotary switches. Panel and shaft sealing up to IP68 against dust and water are standard for all rotary switches. The shaft material for all switches is stainless brass or stainless steel – this is suitable for rugged environments. In order to guarantee years of undisturbed functionality and service life of the rotary switches, all electronic contacts are plated and provided with hard gold. In addition to a large selection of encoders, coding switches, selector switches, audio solutions and multifunctional rotary switches, Elma Electronic offers you also the right knobs and caps.
-
LXinstruments GmbH
Manufacturers of electrical or electronic products are required by law to carry out an electrical safety test before placing them on the market. This final test takes place at the end of the manufacturing process and is therefore also referred to as an EOL test (end-of-line). Depending on the prescribed standard and directive, the following parameters are tested:- Leakage current and discharge current- Insulation resistance or the insulation strenth- Dielectric strength or electric strength- Correct installation of the protective conductor (ground continuity and ground bond test)- Faultless functioning of the product under the conditions defined for intended use (function or run test
-
802.3at and 802.3bt PD Emulation and Protocol Analysis -
Sifos Technologies, Inc.
*Integrated PoE LLDP and Load Emulation in a Single Instrument*IEEE 802.3at and 802.3bt LLDP Compliance Analysis*Independent, Per-Port 802.3at and 802.3bt LLDP Emulations*Flexible Single and Dual Signature PD LLDP Emulations*One-Click LLDP Protocol Capture and Analysis*Pop-Up Excel Spreadsheet Reports Assess Protocol Content and Timing*Enables One-Click Emulated Power-Ups and Standard Waveforms with LLDP Power Granting PSE's*Enables 2-Pair and 4-Pair PSE Conformance Test Suties with LLDP Capable PSE's*Enables 2-Pair Multi-Port Suite with LLDP Capable PSE's*Available for PSA-3000 and PSL-3000 Platforms
-
PSA-3002-SA -
Sifos Technologies, Inc.
Comprehensive Assessment of 2-Pair (802.3at) PoE Service at Any PD Outlet. The only PoE Service Tester built on Sifos PowerSync® Analyzer technology.• Analysis and Troubleshooting for All Standard 2-Pair (802.3at) PoE Installations Including Type-2, LLDP Power • Provisioning• Fully Verify Interoperability of PoE Service to the PD• Verify PoE Service Safety Features• Assess Continuous Power Delivery at the PD by PD Class• Assess Transient Power Delivery at the PD• Troubleshoot Intermittent PoE Service Problems• Colorful Microsoft Excel Reporting• Portable Instrument with Rugged Carrying Case
-
NI
The Serial Interface Device offers a number of options for connecting to serial hardware. You can choose from Ethernet, USB, PCI, PCIe, or ExpressCard interfaces to add up to 16 serial ports to your system. You can choose from common serial protocols, such as RS232, RS422, and RS485. The Serial Interface Device also offers various isolation, hyperthreading, and multiprocessor compatibility options. Some models also support 4- and 2-wire transceiver modes for full- and half-duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
NI
The C Series Serial Interface Module adds RS232 or RS485/RS422 serial ports to CompactRIO systems. The serial ports are accessed directly from the field-programmable gate array (FPGA) to offer you flexibility in communicating with serial devices. The module has individual buffers on every port that save FPGA space and simplify programming. The C Series Serial Interface Module supports standard start bit, stop bit, and handshaking settings. It uses an external power to provide maximum compatibility and reliability under all serial port conditions. You can choose from both enclosed and non-enclosed modules.
-
781341-01 -
NI
The NI‑1483 makes FPGA image processing possible for FlexRIO systems. It supports 80‑bit, 10‑tap base‑, medium‑, and full‑configuration image acquisition from Camera Link 1.2 standard cameras. You can pair the NI‑1483 with a PXI FPGA Module for FlexRIO to perform custom image analysis. FPGA processing is ideally suited for applications that require bit-level processing and very low system latency. Implemented in hardware, FPGA processing does not require CPU intervention. You can process images on the FPGA independently or with a CPU for more advanced preprocessing architectures.
-
783882-01 -
NI
PXIe, 18-Slot, Up to 24 GB/s PXI Chassis—The PXIe-1095 features a high-bandwidth backplane and 58 W of power and cooling in every slot to meet a wide range of high-performance test and measurement application needs. The chassis incorporates two hot-swappable power supplies to improve the mean time to repair (MTTR) of the PXI system; it also offers an optional timing and synchronization upgrade that includes a built-in oven-controlled crystal oscillator (OCXO) for increased clock accuracy and external clock and trigger routing. It accepts PXI Express modules in every slot and supports standard PXI hybrid-compatible modules in up to five slots.
-
786169-01 -
NI
2-Channel, 4-Port, 100BASE-T1 to 100BASE-TX Automotive Ethernet Interface Device—The IVN-8561 is an interface that converts 100BASE-T1 unshielded twisted pair (UTP) automotive Ethernet to standard 100BASE-TX Ethernet. It is ideal for developing applications that require automotive Ethernet to test and validate automotive electronic control units (ECUs). The IVN-8561 provides two channels to convert data between 100BASE-TX Ethernet and 100BASE-T1 Automotive Ethernet. Each 100BASE-T1 port can be configured as master or slave, using switches on the front panel. The IVN-8561 also provides LED on the front panel so that you can monitor the linkage and activity on the various ports.
-
Model T200 -
Teledyne Advanced Pollution Instrumentation
The Model T200 NO/NO2/NOx analyzer uses the proven chemiluminescence detection principle, coupled with state-of-the-art electronics to allow accurate and dependable low level measurements for use as an ambient analyzer or dilution CEMS monitor.A unique AutoZero feature provides superb stability by continuously correcting for zero drift, while advanced Adaptive Filtering allows the analyzer to optimize performance under changing conditions. The Model T200 includes a permeation inlet dryer for ozone generation to provide excellent reliability with no periodic replacement required. A catalytic exhaust ozone scrubber is standard for maximum safety and pump life.
-
Teledyne Relays
- Fully customized switching configurations (from 1x1024 to 24x42)- Universal Power Supply (96-240Vac)- Local Display – High Visibility LED- Standard 19" racks and custom chassis available - Local and/or remote control- 50 and 75 ohm impedances- Multiple interface configurations: - RF ports – SMA, 2.92mm, N, SMB, TNC, etc. - Control – RS-232, Ethernet, USB, Keypad, etc.- Monitor cycle count- Full Command API included- In-circuit programming (firmware upgradable) - Systems can be ruggedized and tested for challenging environments- Passive components Integration (Filters, Attenuators, Dividers, Combiners, etc.)
-
DG Technologies
Besides DG’s vehicle network engineering tools, DG Technologies also offers a variety of diagnostic pass-thru tools for technicians. DG’s hardware and software products are used by a variety of aftermarket customers such as: Mechanics, Technicians, Locksmiths and Vehicle Security Professionals. DG has diagnostic and reprogramming products for automotive vehicles, heavy-duty vehicles and everything in between; all with coverage for engine, brakes, transmission & body. Each of these pass-thru translator tools comes with their own standard diagnostic software and can be used in conjunction with most OEM software to reflash and translate the more detailed manufacturer-specific information acquired from DG’s hardware.
-
JW8006 Series -
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
SLED(Super luminescent light-emitting diode) is a super broadband optical source which is designed for fiber sensor;, optical fiber gyroscope, lab application field. It has the feature as broaden bandwidth, customizable center wave length, high output power, etc. Benchtop (for lab), standard module(150*125*20mm, with modulation function) and mini module(90*70*15mm) is available. The key component is employed the FWHM bandwidth up to 40nm high power SLEDs to ensure the spectrum performance. Stability is ensured by unique ATC and APC circuit. The output power is adjustable by RS232 or RS485 port.
-
Educated Design & Development, Inc.
Fast - All operator controls are located on the front panel to expedite testing. The entire test can be performed in a matter of seconds! Pays for itself in time and stress savings. Versatile - Measures Leakage Current in accordance with UL, CSA, EN, and IEC/ International Standards. Includes ability to perform open neutral, open ground, and line polarity forward/reverse test conditions. Adaptable - Universal rear panel receptacle allows for testing products with any plug configuration. Accurate - True RMS meter accurately measures both sinusoidal and non-sinusoidal waveshapes. This is important when testing products using a switch mode power supply which can generate non-sinusoidal leakage currents. Calibrated, traceable to NIST. Flexible - A front panel switch permits testing either through the power cord of the product under test, from surface/ patient connection-to-ground, or from surface/ patient connection-to-surface/ patient connection. Portable - Lightweight, with integral handle. Other Features - Product Ground Switching (grounding conductor maintained to device under test when not measuring leakage). Automatic front receptacle disconnect when configured in the 240V test mode (prevents inadvertent connection of 120V when configured for 240V operation). Proven - These are the only leakage current testers designed and supported by Product Safety experts. That is part of the reason why they have become the standard in the industry. Full technical support by experienced safety engineers.
-
DRK103C -
Shandong Drick Instruments Co., Ltd.
(1)5 inch TFT color LCD touch screen, the operation is more humanized, new users can be mastered in a short period of time using the method.(2)Simulation of D65 lighting lighting, using CIE1964 complementary color system and CIE1976 (L*a*b*) color space color difference formula.(3)The motherboard brand new design, using the latest technology, CPU uses 32 bits ARM processor,improve the processing speed, the calculated data is more accurate and rapid electromechanical integration design, abandon cumbersome testing process of the artificial hand wheel is rotated, the real implementation of the test program, a determination of the accurate and efficient.(4)Using d/o lighting and observation geometry, diffuse ball diameter 150mm, diameter of the testing hole is 25mm.(5) A light absorber, eliminate the effect of specular reflection.(6)Add printer and imported thermal printer, without the use of ink and color, no noise when working, fast printing speed.(7) Reference sample can be physical, but also for data,? Can store up to ten only memory reference information.(8) Has the memory function, even if the long-term shutdown loss of power, memory zeroing, calibration, standard sample and a reference sample values of the useful information is not lost.(9) Equipped with a standard RS232 interface, can communicate with computer software.
