Filter Results By:
Products
Applications
Manufacturers
Standards
A controlled reference or acknowledged technical criterion.
See Also: IEC, IEEE, Mil, Interoperability Test, Compliance
-
product
Diesel Smoke Analyser
VLT-E9200
The VLT-E9200 diesel smoke analyser measures the opacity of the exhaust gases of vehicles with diesel engines. It can measure if an engine comkplies with the EURO 6 standards. An oil temperature sensor and an rpm counter can be connected.
-
product
Detection of PtG and PtP Faults on Multi and Single Core Cables
CableTroll 2350
CableTroll 2350 is an indicator for detection of PtG and PtP faults on multi and single core cables. The unit uses standard type current transformers. (40:1, 60:1 or 3x500:1)
-
product
Impact Hammer Calibration Device
Shenzhen Chuangxin Instruments Co., Ltd.
It is mainly used for the calibration of the hammer spring, which is based on IEC60068-2-75-1997 and GB2423.55-2006 standard design and manufacturing, primarily for third-party testing organization, the National immigration department and appliance-related research institutes.
-
product
IEC60068-2-75 Spring Hammer Calibration Device
Shenzhen Chuangxin Instruments Co., Ltd.
It is mainly used for the calibration of the spring hammer, which is based on IEC60068-2-75-1997 and GB2423.55-2006 standard design and manufacture, primarily for third-party testing organization, the National immigration department and appliance-related research institutes.
-
product
H-Field Rod Antenna
The A.H. Systems' set of H-Field Rods provide an accurate standard for magnetic field testing. The rods are available individually or in a set of four to cover the frequency range of 100 Hz to 30 MHz.
-
product
Programmable Power Supplies
Genesys™
The Genesys™ series sets the standard for flexible, reliable, AC-DC power systems in OEM, Industrial and Laboratory applications with the highest power density in 1U, 2U or 3U sizes at a competitive price.
-
product
Testing and Conformity Assessment Working Group
The Testing and Conformity Assessment Working Group (TCA WG) is responsible for development and maintenance of those NTCIP standards that are specifically related to testing and conformity assessment, specifically NTCIP 8007 and NTCIP 9012.
-
product
Frequency Converter
A6
The Quartzlock model A6 frequency converter precisely changes either 5 or 10MHz sine wave signals to a number of other frequencies from 1Hz and 1pps upwards to other standard frequencies.
-
product
Auto Pneumatic Bursting Strength Tester
SKZ155D
Determination pressure for a variety of fabrics, including knits, woven fabric, non-woven fabric, laminatedfabric and other craft-made variety of fabrics, in standard conditions or under wet bursting strength andbursting dilation.
-
product
Dual Channel Servo Amp
Servo Amp
This is our Dual Channel Servo Amp board that the instrument shop can use for testing HSI's like the 331A-( ) series and others or RMI's. This board is standard in our model TA-1000 HSI tester.
-
product
Electronic Ballast Tester
LCD for displaying waveforms and parameters directly, and it includes all the functions and technical parameters of WT3000. Reports can be printed if printer is connected. It also meets the latest requirements for electronic ballasts in international standards
-
product
TestStation Rackmount
TSR
TestStation Rackmount (TSR) is designed for easy integration into high-volume automated manufacturing lines. This solution is a collection of specifically designed hardware modules that can be easily integrated into standard or custom automation handling equipment.
-
product
FPGA Boards
Take advantage of FPGA cards built on open standards and with a high degree of configurability in order to address a wide range of applications - without the expense and extensive development time of custom in-house developments.
-
product
Synchroscope
LS-110A SYNC (110V, 120V, 220V, 230V, 240V)
Standard Electric Works Co., Ltd
● Input voltage: 110V AC, 120V AC, 220V AC, 230V AC or 240V AC.● Standard 4.5 inch switchboard● Front panel mount● 360° indication● Metal case
-
product
Noise Figure Measurements With Vector Correction
S97029B
The instrument’s standard receivers are used for noise figure measurements with the S97029B. An external preamplifier and filter(s) is required for devices with < 30 dB of excess noise (gain plus noise figure in dB)
-
product
COM Express Solutions
COM Express® is a PICMG® standard that defines a Computer-On-Module in a family of Small Form Factors (SFF). It is single board computers appropriate for a wide range of commercial and mil/aero applications.
-
product
Leak Tester
DRK134
Shandong Drick Instruments Co., Ltd.
DRK134 Leak Tester is an advanced and intelligent tester designed according to related standard. It is applicable to test the seal property of flexible pack in food industry, pharmacy industry and daily chemical industry.
-
product
ATCA 5U 14 Slot Mesh w uTCA connector for SHMM
1900001778-0000R
The 14-slot mesh backplanes have standard 1X full mesh topologies. Elma Electronic’s ATCA backplanes have been simulated and characterized by our signal integrity lab to optimize performance.
-
product
3U VPX Dual-Plane Gen3/4 PCIe & 40 Gigabit Ethernet Switch
ComEth4420e
The ComEth4420e is a cutting-edge hybrid managed switch combining PCIe Gen3/4 and 10/40 Gbs Ethernet technologies. It has been developed in alignment with the SOSA (Sensor Open Systems Architecture) Technical Standard.
-
product
Surface Condition
Surface Condition: degree or percentage of rust, level of mill scale, etc., can be visibly assessed using Pictorial Surface Standards. Weld beads can be assessed using a weld comparator and weld gauges.
-
product
Fiber Geometry System
FGC-GS
The FGC range is the complete solution for measuring the dimensions of standard and specialty fiber in both production and R&D environments. FGC-GS – fiber glass geometry for fibers up to 1000 µm diameter.
-
product
Interferometer
VFI-200
The FGC range is the complete solution for measuring the dimensions of standard and specialty fiber in both production and R&D environments. FGC-GS – fiber glass geometry for fibers up to 1000 µm diameter.
-
product
PD Conformance Test Suite
Sifos Technologies offers the ultimate simplicity in testing a PD’s conformance to IEEE 802.3 Standards with Pass/ Fail reporting in the PD Conformance Test Suite available for purchase with the PDA-600 Family of Instruments.
-
product
CPCI Type 15C, Rackmount/Desktop
15C-CPCI
Type 15 Rackmount/Desktop Elma System 15 enclosures provide an elegant and versatile platform. Designed to Eurocard and IEEE standards, System 15 enclosures give advanced EMC shielding protection.
-
product
19" enclosure in excellent design
Stylebox-15-e-motion
A portable desktop enclosure according to 19" standards. It can also be used as a 19" plugin device. The scalable EMC protection, color and design variants make the box the first choice for high-end electronics.
-
product
Enclosure Accessory Kit, Gas Spring for Sloped Enclosure
410114133
The sloped enclosures come capable of having a Gas Spring accessory installed on the left, right or both sides of the enclosure. The enclosure comes standard with one Gas Spring accessory on the right side.
-
product
IK07-IK10 Pendulum Impact Hammer Apparatus
Shenzhen Chuangxin Instruments Co., Ltd.
IK07-IK10 Pendulum Impact Hammer Apparatus is desinged according to IEC60068-2-75 and IEC62262 standards. The IK07-IK10 Pendulum Impact Hammer Apparatus can be used for the mechanical impact strength test of metal enclosure.
-
product
CPCI Type 32C Portable Tower Family
32C-CPCI
Elma Type 32C family of enclosures provide a lightweight, tower platform for packaging portable CompactPCI applications. Designed to IEEE 1101.10/.11. Standard features include feet and carrying handle.
-
product
DC Precision Measuring
Precision instruments for calibrating and monitoring. Our line of Precision Bridges, Decade Boxes, Galvanometers, Potentiometers, and standard high precision resistors, allow customers the accuracy and quality demanded in a precision device.
-
product
Oscilloscope: 200 MHz, 4 Analog Channels
DSOX3024T
The DSOX3024T, 200 MHz oscilloscope provides 4 analog channels, 4 Mpts memory, 1,000,000 waveforms/sec update rate and standard touch zone trigger with an 8.5-in capacitive touch screen.