Showing results: 706 - 720 of 6648 items found.
-
DMX ADAPTER -
EMO Systems Canford Audio PLC
DMX protocol is a standard means of controlling lighting dimmers remotely from a control desk. The standard uses a three wire connection using 5-pin XLR type connectors. These adapters allow the E445, E446 and E447 table testers to be used to test the primary circuit of such cables. Two adapters are required for each cable tester.
-
PortaTest -
Schleich Gmbh
Portatesters are easy to use. Based on the test standard, you select the corresponding test sequence. Then, the required test probe and the electrode gap for the selected test standard is displayed. The setting gauge, included in the scope of delivery, facilitates the adjustment of the electrode gap. Afterwards you fill the insulating oil in the test vessel and close the test chamber.
-
K8213A -
Keysight Technologies
Keysight’s Interconnect Plus Boundary Scan 1149.6 feature enables all the tools required to develop and execute this test method on the board under test. Compared to the 1149.1 standards, the 1149.6 standards define test methods for the boundary scan devices that are designed with AC coupled signals or differential nets needed for high-speed operations of the device.
-
K8213B -
Keysight Technologies
Keysight’s Interconnect Plus Boundary Scan 1149.6 feature enables all the tools required to develop and execute this test method on the board under test. Compared to the 1149.1 standards, the 1149.6 standards define test methods for the boundary scan devices that are designed with AC coupled signals or differential nets needed for high-speed operations of the device.
-
Dewesoft d.o.o.
Class 1 Sound Level Meter and Noise MeasurementThe golden standard for sound noise level meter reimagined with the Dewesoft approach. Easy to set up and use while ensuring maximum accuracy with certified compliance with international standards. No matter the type of acoustics measurement, a sound level meter is always at the heart of the sound analysis.
-
JMY-16 -
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.4-2008; Inspection standard: JB/T4279.16-2008Used to detect static friction coefficient (μs) of enameled round wires with nominal conductor diameter ranging from 0.050mm to 1.600mm;The application of high-end SCM control allows for high sensitivity and excellent repeatability.Four-digit LED would automatically display static friction coefficient (μs) of sample;
-
JW8102 -
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
JW8102 Four-Channel Optical Power Meter provide superior dynamic range and Linearity technical index . It adopts RS232-C and RS485 communication interface, can communicate directly with PC, and communication protocol is compatible with standard instruction.The reduced instruction can greatly increase the communication rate with the PC, and the standard instruction can greatly improve the reliability of the communication with the PCB.
-
SKU-067-0X -
Amfeltec Corp.
Flexible x1 PCI Express to MiniPCI Bus Adapter (Adapter) was designed to convert PCI Express bus into standard MiniPCI bus. It allows connection of a standard 124-pin MiniPCI add-in board to a motherboard PCI Express connector.Adapter includes a MiniPCI Adapter board (downstream), x1 PCI Express host board and flat PCI Express cable.
-
NSG 5071 -
Teseq AG
The basic philosophy of this test circuit is better reproducibility of actual switching transients. The reproducibility of this test circuit comes not from the output characteristics as in traditional conducted automotive immunity tests, but from a fixed design of the generator using several pre-defined components. Many of these components are defined in the standard as "critical" with no substitutions allowed. These components are used as required in the standard.
-
Lisun Electronics Inc.
The standard test temperature is 25, but high power lamps such as HID lamps and LED outdoor luminaires will produce a lot of heat during the test, thus the temperature inside the integrating sphere can not meet the requirements of IEC standards. Lisun Group designed the Constant Temperatured Integrating Sphere which allows the lamp was tested in a constant air temperature.
-
310104402 -
Virginia Panel Corporation
This 50 module receiver is designed to fit into a standard 19” rack. It is equipped with a locking handle to ensure proper ITA engagement. A standard integrated microswitch shuts off power when the ITA disengages from the receiver. This receiver is designed to work with a slide kit and includes mounting flanges and instrument brackets. A slide kit is required for use, but not included.
-
DP-VME-1427 -
Data Patterns Pvt. Ltd.
The DP-VME-1427 is a standard 6U VME based general purpose 32 channel Analog to Digital Convertor (ADC) module. The module is a slave VME 64x interface, that responds to A24/D16 standard VME address cycle. On-board auto-conversion circuitry performs all the task related to multiplexing, sampling and converting of analog input signals to the digital outputs.
-
innco systems GmbH
Antenna Masts are an integral part of EMC and RF measurement systems. Innco system masts are renowned worldwide as the standard benchmark. Available in manual or automatic, using either pneumatic and or electric driven, the antenna mast design has the capacity to carry antennas of 6kg (MM) and 10kgs (MA) as standard. Higher loads are available upon request.
-
Teledyne RF & Microwave
This custom oscillator subassembly consists of two low noise oscillators covering 1.5 to 2.5 GHz, a power combiner, a standard Teledyne RF & Microwave amplifier, and a lowpass microstrip filter. Teledyne RF & Microwave designed both oscillators for low phase noise and linear tuning. The output frequency bands are switched using standard TTL control.
-
Universal Wireless Tester -
NOFFZ Computer Technik GmbH
Wireless communication standards are increasingly integrated into vehicles as well as smart home and Internet-of-Things applications. They form the basis for connected services, advanced HMIs, and autonomous driving. The combination of constantly evolving standards and the integration of multiple wireless technologies with many RF channels into new product designs means that measurement speed and quality are becoming a priority.