Showing results: 871 - 885 of 6648 items found.
-
Di-Log
The Di-LOG range to test leads are designed and manufactured to the highest quality and meet all safety standard as stipulated in BS EN 61010
-
Advantech Co. Ltd.
Advantech CPCI solution includes GPU, Ethernet, storage blades, and AC/DC power modules that comply with industry standards for broad compatibility.
-
EC-12 -
Lumetronics
The Earth bond test is a basic safety test prescribed in many standards to test samples for the integrity of earthing continuity throughout the sample.
-
7000 -
ELMA Electronic, Inc.
This low-cost family of CompactPCI adapters enables the use of standard and custom 32-bit based PMC modules in a 3U or 6U CompactPCI system.
-
-
A291800-03 -
Chroma ATE Inc.
The A291800 is an LVDS signal model that can be used with FPD Tester to provide LVDS panel standard signals and related controls for LVDS inspection.
-
BCL-1 -
Lisun Electronics Inc.
This Pull out device BCL-1 is designed and manufactured according to relevant standard requirements of IEC884-1/ GB2099.1-2008 and other electrical accessories standards, Mainly used to test the needed maximum force when the plug pull out from socket and the minimum force when single stage plug pull out from socket, and to inspect whether the socket can withstand the lateral stress imposed by electric plug into the socket. This device is applied to plugs and sockets which rated voltage no more than 250V and rated current no more than 16A.Specifications: • Weights: 36N*1, 5.4N*1, 5N*2, 4N*1, 2.6N*1; • Standard testing plug: each one for Dipolar 10A, tripolar 10A and 16A • Standard test bolt: Each one for 1.5N and 2N • 1 set of clamping device • 1 set of Weights tray • Lateral stress weights 5N*1 • 1 set of lateral stress bar
-
M Series -
Com-Power Corporation
Coupling Decoupling Networks are recommenced for all power supplies connections. The distubance signals are coupled to each conductor in the supply lines according to EN 61000-4-6 standard. The standard M series CDNs have a current rating of 25 Amps. Com-Power CDNs are available for power supplies from 1 to 5 conductors. These CDNs cover the frequency range of 150 kHz - 230 MHz.
-
Daqarta
Standard Windows sound cards do not respond to DC or frequencies lower than a few Hz. (See Why Sound Cards Block DC Signals below for explanation.)There are two general approaches to get true DC response from a standard sound card: Modify the card, or add an external circuit to convert the DC into an AC signal which can be easily measured by an unmodified card.
-
TOS9300 Series -
Kikusui Electronics Corp.
The TOS9300 series is a high performance electrical safety analyzer that complies to a wide range of universal standards. Hipot, Insulation Resistance, Ground Bond, Leakage Current (touch current and protective conductor current) and partial discharge can all be tested. A total of 6 models are available for standard compliance tests in a wide variety of applications including R&D, quality assurance manufacturing lines and laboratory tests.
-
SKU-066-0X -
Amfeltec Corp.
Flexible MiniPCI Express to MiniPCI Bus Adapter (Adapter) was designed to convert motherboard MiniPCI Express bus into a standard MiniPCI bus. It allows connection of a standard 124-pin MiniPCI add-in board to a motherboard’s MiniPCI Express connector via full- or half-size MiniPCI Express host board.Adapter includes MiniPCI Adapter board, MiniPCI Express host board and flat PCI Express Cable.
-
CIX100 -
Olympus Corp.
The OLYMPUS CIX100 inspection system is a dedicated, turnkey solution for manufactures who maintain the highest quality standards for the cleanliness of manufactured components. Quickly acquire, process, and document technical cleanliness inspection data to comply with company and international standards. The system’s intuitive software guides users through each step of the process so even novice operators can acquire cleanliness data quickly and easily.
-
LPPHOT03… Series -
Delta OHM S.r.L.
The probe LPPHOT03 measures illuminance (lux), defined as the ratio between the luminous flux (lumen) passing through a surface and the surface area (m²). The spectral response curve of a photometric probe is similar to the human eye curve, known as standard photopic curve V(λ). The difference in spectral response between LPPHOT03 and the standard photopic curve V(λ) is calculated by means of the error f’1.
-
310104369 -
Virginia Panel Corporation
This 50 module platform receiver is equipped with a locking handle to ensure proper ITA engagement. A standard integrated microswitch shuts off power when the ITA disengages from the receiver. Uses all standard VPC modules and contacts, includes a microswitch and is available with optional table legs and keyboard tray kit. Includes mounting flanges and instrument brackets. A slide kit is required for use.
-
HY-TTC 30XSH -
TTTech Computertechnik AG
HY-TTC 30XSH, a member of the HY-TTC 30X family, is certified by TÜV Nord according to the EN 13849 standard and fulfills Performance Level c (PL c) requirements. Just as the other family members this certified unit must be used in combination with a master module. For safe communication the standardized CANopen Safety protocol is applicable since compliance to the European standard EN 50325-5 for CANopen Safety is provided.