Showing results: 5536 - 5550 of 6660 items found.
-
40-737A-001 -
Pickering Interfaces Ltd.
The 40-737A-001 (PXI) and 42-737A-001 (PXIe) are 16:1 USB data communications multiplexers suitable for switching USB1 and USB2 data and power connections using a 78 way D-Type connector. The data signal paths are 2-pole arranged as differential pairs as defined by the USB standard. The signal pair has a controlled differential impedance and the multiplexer has been designed for minimum insertion loss. The USB power paths are arranged as a common negative and a switched positive. The power paths are designed to ensure minimum loss of the USB power.
-
Teledyne Lincoln Microwave
The Gunn diode is the best known and most readily available device in the family of transferred electron devices (TED). They are employed as DC to microwave converters using the negative resistance characteristics of bulk Gallium Arsenide (GaAs) and only require a standard, low impedance, constant voltage power supply, thereby eliminating complex circuitry. Teledyne Lincoln Microwave’s DC1200 series of GaAs Gunn diodes is designed for operation at fixed frequency (determined by the oscillator cavity) within a specified band under CW or pulsed conditions.
-
SeaBat T20-S -
Teledyne Marine RESON B.V.
The T20-S is a new addition to the leading SeaBat product range engineered from the ground up to evolve with your business.Combined with the all-new Subsea Sonar Processor the T20-S provides the highest quality survey data in a fully integrated sonar processing and data storage unit housed in a subsea pressure vessel. Smaller form factor and reduced operational power to extend mission time for battery powered underwater vehicles. Internal data storage for self-contained survey solution, and interfacing via standard Ethernet to reduce integration time.
-
Teledyne Labtech
For many years Teledyne Labtech has manufactured RF & Microwave PCB with integrated OhmegaPly® resistors. OhmegaPly® is a thin film resistor-conductor material. Using standard subtractive printed circuit technology, integral resistors are formed on circuit layers. These resistors can be buried within a Multilayer circuit board or used on the board surface. The resistors can also be used mounted on Metalbacked PCB.OhmegaPly® is available in 25 ohm per square, 50 ohm per square and 100 ohm per square sheet resistivity.
-
PAS-Products
Turns your computer into a modern, State-of-The-Art spectrum analyzer giving you. features that go far beyond the possibilities of any stand-alone hardware unit. An important advantage of your new analyzer software is the fact that your computer monitor is a far better means of displaying analyzer measurments than any LED or LCD bar. By making use of standard computer operations your analyzer software will store your personal settings or analyze audio data you may have previously recorded.
-
BAT -
ADVINT, LLC
• NI PXIe Based Platform for Radar/EW Test- Leverages a Variety of NI FPGAs/VSTs/Upconverters up to 44GHz- LabVIEWTM and LabVIEWTM FPGA Software Environment• Provides PDW to IQ Generation• Multi-Emitter System- Faster Simulation Setup- More Complex Scenario Testing- Ease of Changing Scenarios• Supports Multiple PDW Formats- Simple, Built-In PDW Format- Industry Standard PDW Formats (e.g., NEWEG)- Custom PDW Formats• PDW Data Accessible via Stored Files, or Live Streaming• Factory to Field Deployable
-
OAKTON Instruments
Rugged, accurate, reliable – Best value for an IP67-rated waterproof meter!*Intuitive, user-friendly icons—electrode status displays pH slope*Grip-Clip™ holder quickly and easily secures the electrode to your beaker or container*Expanded data logging for up to 150 data sets*mV offset for calibration of ORP standards, zeroing mV value, and pH diagnostics*700 hours battery-life or optional universal power adapter*Built-in stand and wall mount option allow for easy benchtop measurement or storage
-
CD23/223 -
Validyne Engineering
The CD23 and CD223 Digital Transducer Indicators are designed for use with variable reluctance and differential transformer transducers. The CD23 accepts input from a single transducer, and the CD223 accepts two switch-selectable inputs, with Zero and Span controls for each input. The indicators provide 5 Vrms, 5 kHz carrier excitation voltage to the transducer(s) and solid state circuitry to amplify, demodulate and filter the transducer output signals. A 3 1/2 digit front panel display is standard, with a 4 1/2 digit display optionally available.
-
MT -
Instron
The MT Series torsion testing systems are available in six standard models with force capacities ranging up to 5,650 N-m (50,000 lbf-in) and are used for torsion testing and component in-service simulation. The compact design requires minimal lab space and offers superior frame stiffness and alignment. Packaged with Instron high-performance control electronics, the MT Series provides highly accurate test data and control for testing wire, fasteners, metal components, switches, and springs used in the biomedical, automotive, aerospace, and construction industries.
-
60-983-002 -
Pickering Interfaces Ltd.
The 60-983 is an LXI compatible Wired Trigger Bus Terminator (WTB) designed to be attached to the end of a WTB cable. The LXI WTB uses a transmission line cable to connect LXI devices together that support the WTB capability of the LXI standard. Like all transmissions it needs to be correctly terminated to avoid reflections that could change the signal amplitude along the cable and generate timing jitter or trigger errors. The 60-983 is a simple terminator that can be placed at each end of the WTB chain to correctly terminate the transmission line with minimal reflections.
-
60-983-003 -
Pickering Interfaces Ltd.
The 60-983 is an LXI compatible Wired Trigger Bus Terminator (WTB) designed to be attached to the end of a WTB cable. The LXI WTB uses a transmission line cable to connect LXI devices together that support the WTB capability of the LXI standard. Like all transmissions it needs to be correctly terminated to avoid reflections that could change the signal amplitude along the cable and generate timing jitter or trigger errors. The 60-983 is a simple terminator that can be placed at each end of the WTB chain to correctly terminate the transmission line with minimal reflections.
-
60-983-001 -
Pickering Interfaces Ltd.
The 60-983 is an LXI compatible Wired Trigger Bus Terminator (WTB) designed to be attached to the end of a WTB cable. The LXI WTB uses a transmission line cable to connect LXI devices together that support the WTB capability of the LXI standard. Like all transmissions it needs to be correctly terminated to avoid reflections that could change the signal amplitude along the cable and generate timing jitter or trigger errors. The 60-983 is a simple terminator that can be placed at each end of the WTB chain to correctly terminate the transmission line with minimal reflections.
-
Solidus Technologies, Inc.
olidus Technologies’ can design and build a test system customized for your exact needs, using our own or off the shelf components:Custom MEMS Test Systems. We can integrate and assemble test equipment and handling systems to fit your requirements. Custom MEMS Test Software. We can write custom software for device-specific calibration and testing, interfacing various instruments and handling systems, or create a customized GUI. We can also adapt our standard STI Test Software to work on your hardware system.
-
CX-F01 -
Shenzhen Chuangxin Instruments Co., Ltd.
This device is according to the IEC60320-1 standard requirement to design. Appliance inlets designed for surface mounting and having a shroud of metal, are compressed in an appropriate test apparatus, an example of which is shown in figure 20. The spherical end of the jaws shall have a radius of 20mm±1mm. A force of 40N±2N shall be applied for 60s±6s through the jaws to the most unfavourable point half-way up the outer surface of the shroud, in a direction perpendicular to the axis of the shroud. After the test, there shall be no deformation or loosening of the shroud such as will impair the further use of the appliance inlet.
-
Amprobe Test Tools
When you work with electricity, you want tools that are field tested and proven to meet the highest standards. All Amprobe tools undergo rigorous examination in our state of the art testing labs, ensuring quality and full compliance with the latest IEC and CE safety regulations. They are also listed with third party certification labs worldwide. Amprobe electrical testers include circuit tracers and testers, non-contact voltage detectors, voltage meters, socket testers and more to cover all aspects of electrical testing.
