Showing results: 2746 - 2760 of 7529 items found.
-
MFG-8205 -
MCH Instruments Co.,Ltd.
Features:• Low distortion, high stability• Linear and logarithmic sweep function• Sweep time and width adjustable• External Voltage Control Frequency (VCF)• Internal & external modulation (AM/FM) with modulation control• Output signal compatible with TTL/CMOS• Seven types of waveforms such as sine, square, triangle and ramp• 5W power output (ONLY for model no with “B”)• DC offset and 40bD attenuation can be applied to main output signal• Built-in frequency meter 0.1Hz~30MHz
-
ZLX Series 0.6” x 0.6” x 0.15” -
EM Research, Inc.
*Surface Mount Miniature Package *Excellent Phase Noise *Optional Internal Reference *Output Power to +10 dBm Available
-
LX Series -
EM Research, Inc.
*Surface Mount Miniature Package *Optional Internal Reference *Output Power to +10 dBm Available
-
LX Series 0.75” x 0.75” x 0.15" -
EM Research, Inc.
*Surface Mount Miniature Package *Optional Internal Reference *Output Power to +10 dBm Available
-
Amprobe ACDC-54NAV -
Amprobe Test Tools
The ACDC-54NAV clamp-on power meter offers AC/DC current measurements to 1000 A, AC/DC voltage to 1000 V, temperature capabilities, and wide jaws to handle large conductors up to 1.6″ (40 mm) for high voltage industrial environments.
-
PT-20MG -
TTTech Computertechnik AG
The PT-20MG expands the PM-200 data logger from the Power Family by adding six 1000BASE-T1 automotive gigabit Ethernet interfaces. Ethernet traffic is looped through the device with constantly low latency irrespective of the frame length. This means that the time synchronization protocols of the logged Ethernet interfaces are not affected. 1000BASE-T1 packets are time-stamped, filtered and sent to the data logger via a 1000BASE-T interface.
-
Series HSM -
Kepco, Inc.
The Kepco HSM series comprises a group of ten models, seven 1000 watt power supplies with outputs from 3.3 volts to 125 volts and three 1500 watt power supplies with outputs from 24 to 125 volts. All models feature current sharing for parallel operation and redundancy applications. Kepco¹s 1000W HSM have a wide-range input (90-277V a-c). The 1500W models operate 180-277V a-c. Both incorporate power factor correction to meet EN 60555-2 and EN 61000-3-2. These modern power supplies operate at 100KHz using current mode control to provide rapid response to source and load changes and tight stabilization.
-
PT-15B -
TTTech Computertechnik AG
The PT-15B expands the PM-200 data logger from the Power Family by adding twelve 100base-T1 interfaces. Ethernet traffic is looped through the device with constantly low latency irrespective of the frame length. This means that the time synchronization protocols of the logged Ethernet interfaces are not affected. 100base-T1 packets are time stamped, filtered and sent to the PM-200 data logger via a 1000base-T interface.
-
HCF-F1000L -
MCH Instruments Co.,Ltd.
FEATURE:*Period,totalize measurement self test*High sensitioity:85dBV (25mVrms)*Stability:±3x10-9/s*8 digit LED display*Gate Time:0.01s,0.1s,1s*Power supply:AC 220V(110V optional)
-
bel Power Solutions
The TSR10 is a 10 kW, 3-phase input voltage 360 - 440 VAC power supply with an adjustable DC output voltage between 0.5 V and 50 V and output current between 0.5 A and 200 A. The power supply has been designed for the industrial and laboratory applications, featuring front panel display for setting and monitoring output voltage and current within a 3U profile.
-
CM-51 -
Taylor Dynamometer, Inc.
AC power, air and water required at one side wallas applicable.• Room length, and pit location within length,must be determined by user to fit maximumtruck length and rear overhang.• Provide at least one man door for fire escapenear rear of room, but not in rear wall becausesomeone entering during a test could be struckby a stone flung from a tire. Provide ample fireextinguishers at each door and near driver.• “Back-on, Drive-off” installation configurationpreferred.
-
TD-24 -
Taylor Dynamometer, Inc.
AC power, air and water required at one side wallas applicable.• Room length, and pit location within length,must be determined by user to fit maximumtruck length and rear overhang.• Provide at least one man door for fire escapenear rear of room, but not in rear wall becausesomeone entering during a test could be struckby a stone flung from a tire. Provide ample fireextinguishers at each door and near driver.• “Back-on, Drive-off” installation configurationpreferred
-
CP6007-SA -
Kontron AG
CP6007-SA is based on 6-core or 8-core 11th Generation Intel® Xeon® processors with 10nm technology, with outstanding performance-per-watt values. Its scalable power budget allows users to tailor the power dissipation to their requirements. 32GB soldered memory and the option for an additional 32GB SODIMM with ECC is provided.
-
Series KLP -
Kepco, Inc.
The KLP is an entirely new laboratory grade power supply in which the voltage/current limits are automatically recalculated, forming a constant-power hyperbolic-shaped boundary between the voltage and current modes. This curve, which replaces the single max-power operating point of conventional power supplies, provides the user with a greatly expanded choice of maximum power volt-ampere combinations as illustrated in the diagram by points A to B to C. The constant-power limit of the KLP is 1200 watts.
-
524 -
Dataman, Inc
The Dataman 524 is a dual channel oscilloscope with 120 MHz bandwidth and USB 2.0 connectivity • USB powered - no additional power supply is required • Dual channel with external trigger • 120 MHz bandwidth • 100 MS/s real time sampling rate • 10 GS/s equivalent sampling rate • 8,000 sample buffer per channel • Hi-speed USB 2.0 connectivity allowing fast and easy connection to PC’s and laptops • Comprehensive 2 years parts and labor warranty • Free life-time software updates