Showing results: 3061 - 3075 of 7529 items found.
-
Model 4804B-7 -
ICS Electronics
* F30145 firmware converts printable ASCII character strings into the ANSI X3.28 serial protocol.* User selectable single-ended RS-232 and differential RS-422/RS-485 serial signals.* Can be used to replace obsolete ICS 4814 Interfaces.* Connect to the rear panel with a GPIB Flat-ribbon cable or with a GPIB Connector/Address Switch Cable.* Runs on 5 Vdc regulated or 5.5 to 15 V unregulated power.
-
EM-6917B-1 | 30 MHz To 3 GHz -
Electro-Metrics Corp.
The EM-6917B-1, a hybrid combination of the industry standard biconical and log periodic antennas, delivers an unmatched combination of frequency coverage and high power handling capability. Featuring exceptionally broad frequency coverage of 26 MHz to 3 GHz, the EM-6917B-1 eliminates the need for adjustments or switching antennas in most test applications up to 3 GHz, and it does so without compromising power handling capability for transmit applications.
-
EM-6917C-1 | 26 MHz – 1 GHz -
Electro-Metrics Corp.
The EM-6917C-1, a hybrid combination of the industry standard biconical and log periodic antennas, delivers an unmatched combination of frequency coverage and high power handling capability. Featuring exceptionally broad frequency coverage of 26 MHz to 1 GHz, the EM-6917C-1 eliminates the need for adjustments or switching antennas in most test applications up to 1 GHz, and it does so without compromising power handling capability for transmit applications.
-
EM-6946 | 300 MHz – 3 GHz -
Electro-Metrics Corp.
The EM-6946 offers an exceptional combination of frequency coverage of 300 MHz –3 GHz and high power handling capability without compromising the consistent performance versus frequency that makes the log periodic antenna so desirable for test applications.
-
EM-6944 | 200 MHz – 3 GHz -
Electro-Metrics Corp.
The EM-6944 offers an exceptional combination of frequency coverage from 200 MHz – 3 GHz and high power handling capability without compromising the consistent performance versus frequency that makes the log periodic antenna so desirable for test applications.
-
ANC-4 -
Timewave Technology Inc.
The ANC-4 is an rf device that eliminates or reduces power line noise, BPL noise, computer noise, TV-generated interference, and other types of electrical noise. The ANC-4 unit connects right to the antenna connector of the receiver or transceiver to cancel locally generated noise before it gets into the receiver and affects the receiver AGC circuits.
-
AI-Series -
Hilkar
AI-series anti-islanding load banks containing purely resistive, inductive, or capacitive load, have segmented combination control of power input, and can simulate a variety kinds of power loads to meet the grid-connected inverter full load test requirements.
-
AX93274 -
Axiomtek Co., Ltd.
*PoE-PD I/O board complies with IEEE802.3at standard via an internal cable to power on SBC*100 x 32 mm*1 x LAN cable, 1 x power cable, 1 x thermal module*Compliant products: PICO831, PICO121, PICO841, PICO843
-
Ulia -
Uila, Inc.
Uila provides real-time visibility into the Application & Business Service Dependencies and also powers the IT teams with deep insights into web and database applications to allow for the issues to be narrowed down and mitigated.
-
Arasan Chip Systems, Inc.
Arasan PHY’s are readily available and in production with multiple foundries from 16nm to 180nm. Our PHY’s are designed for low power on the most advanced nodes for the mobile market while also targeting the automobile market on specialized nodes where extreme temperature tolerance is required.
-
M531 -
ETC
The M531 is a single channel USB arbitrary waveform generator compatible with USB 2.0 and USB 1.1 interface. The generator has two outputs: both generate same waveform, but with different peak-peak voltage. The low level output has 50ohm output impedance and maximal peak-peak voltage of 9V. There is no external power supply required to enable low level output (it is powered from USB bus).
-
VME-194B -
Curtiss-Wright Defense Solutions
The VME-194B is the next generation of VME single board computer (SBC) from Curtiss-Wright Defense Solutions. It is targeted for applications with moderate processing requirements, low power and cost effectiveness. The VME-194 VME SBC is based on NXP's high performance QorIQ P2020 SOC multi-core processor. The VME-194B provides highperformance processing, and a long list of features and I/O interfaces to satisfy the most demanding requirements of embedded computing.
-
VME-186 -
Curtiss-Wright Defense Solutions
The VME-186 VME Single Board Computer is based on NXP's high-performance QorIQ P4080 SOC multi-core processor. With four or eight Power Architecture cores running up to 1.5 GHz, and up to 8 GB of high bandwidth DDR3 SDRAM, the VME-186 SBC provides processing and a variety I/O interfaces to satisfy the most demanding requirements of embedded computing.
-
IFB-10003-INP -
Playing With Fusion Inc
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
-
IFB-10003-ANP -
Playing With Fusion Inc
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
