Showing results: 6406 - 6420 of 7529 items found.
-
GX7400A -
Marvin Test Solutions, Inc.
The GX7400A is a dual output programmable DC power supply designed for use in 6U PXI systems. The GX7400A occupies three slots and is controlled via the PXI bus. The AC power is provided using a panel-mounted receptacle. The power supplies are fully isolated and can be externally connected in series to provide higher voltage.
-
SIU32-RIUVARM-01 -
North Atlantic Industries
SIU32-RIUVARM-01 is a Modular Open Systems Approach (MOSA) Remote Interface Unit (RIU) to manage, monitor and control connected I/O, communications, measurement and simulation interfaces through Ethernet commands from a main mission processors. Extremely low power with 2 x 10/100/1000Base-T Ethernet.
-
NIU3A-AIC-01 -
North Atlantic Industries
NIU3A-AIC-01 is a Modular Open Systems Approach (MOSA) Aircraft Interface Computer with low power high performance ARM Cortex -A53 processing. 8 GB RAM, 32 GB SATA Flash, 2 x 10/100/1000Base-T Ethernet.
-
NIU3A-DCU-01 -
North Atlantic Industries
NIU3A-RDC-01 is a Modular Open Systems Approach (MOSA) Data Concentrator with low power high performance ARM Cortex -A53 processing. 8 GB RAM, 32 GB SATA Flash, 2 x 10/100/1000Base-T Ethernet.
-
VMA -
North Atlantic Industries
NAI’s VMA is a field-adjustable, AC-Powered, AC Voltage Monitor used to monitor voltage characteristics of single- or three-phase power lines. This allows normal operation of system loads when the power-line characteristics are within pre-determined limits.High and low voltage limits, and "pick-up" and "drop-out" time delay are field-adjustable. The VMA voltage monitor is ideally suited for rugged defense and industrial applications.
-
VAA/VQA -
North Atlantic Industries
NAI’s VAA and VQA are AC-Powered, AC Voltage Monitors used to monitor voltage characteristics of single- or three-phase power lines. This allows normal operation of system loads when the power-line characteristics are within pre-determined limits. These voltage monitors are ideally suited for rugged defense and industrial applications.
-
VAD/VQD -
North Atlantic Industries
NAI’s VAD and VQD are DC-Powered, AC Voltage Monitors used to monitor voltage characteristics of single- or three-phase power lines. This allows normal operation of system loads when the power-line characteristics are within pre-determined limits. These voltage monitors are ideally suited for rugged defense and industrial applications.
-
NIU2A-RDC-01 -
North Atlantic Industries
NIU2A-RDC-01 is a Modular Open Systems Approach (MOSA) Remote Data Concentrator with low power high performance ARM Cortex -A9 processing. 512 MB RAM, 32 GB SATA Flash, 2 x 10/100/1000Base-T Ethernet and optional Fiber Optic Ethernet support.
-
3512 -
Abaco Systems Inc
The 3512 is an eight channel non-isolated digital I/O board with +5V tolerant 74LCX14 inputs with hysteresis and +3.3V CMOS 74LVTH125 driven outputs. Each I/O line features a series 10 ohm damping and protection resistor and a 4.7K pull up resistor to +3.3V. On power up the outputs are tri-stated, and can then be enabled on a bit by bit basis. Output high drive is 32mA @ 2.0V minimum. Output low drive is 32mA @ 0.8V maximum.
-
DSP282A -
Abaco Systems Inc
Designed for size, weight and power (SWaP) sensitive applications, Abaco's high performance embedded computing (HPEC) platforms deliver expanded mission capabilities across a wide range of manned- and un-manned airborne, ground and naval platforms.
-
5033 -
Abaco Systems Inc
ECM P/N 5033 provides eight channels of RS485 / RS422 I/O. The 110 ohm termination for each channel is enabled or disabled in software. Disabling termination saves power by eliminating unneeded or redundant termination. Speeds of up to 20 Mega bits per second are possible, but this design also features a 250K bits per second slower edge rate mode. The 250K bit mode is valuable when EMI is more of a concern and throughput is not important. All channels power up as inputs with the outputs disabled.
-
5362 -
Abaco Systems Inc
ECM P/N 5362 provides eight channels of LVDS I/O with fixed 100 ohm termination. Speeds are up to 200M bits per second. All channels power up as inputs. Software can then enable outputs on a channel by channel basis.
-
SBC627 6U -
Abaco Systems Inc
The SBC627 rugged 6U VPX single board computer offers more processing power, more bandwidth, and more graphics capability – with no increase in the size, weight or power requirements of previous generations – enabling fewer system slots to be used. The FPGA combines a mix of passive and active features to allow customers to develop a robust on-board anti-tamper capability.
-
SBC346 3U -
Abaco Systems Inc
Based on the optimized 4th Generation Intel® Core™ i7 architecture, the VPXcel3 SBC346 in a rugged OpenVPX 3U form factor delivers up to a 15% CPU performance boost over 3rd generation technology; graphics support for DX11.1, OpenCL 1.2, OpenGL 3.2; connectivity with flexible I/O and security – all within the same power envelope as its predecessors.
-
SBC347D 3U -
Abaco Systems Inc
The VPXcel3 SBC347D rugged single board computer is based on the highly integrated Intel® Xeon® D processor platform. The multiple core Xeon D brings the high performance of Intel Xeon processors into a dense, low power system-on-chip solution, ideal for High Performance Embedded Computing (HPEC) applications.