Showing results: 4861 - 4875 of 11167 items found.
-
Pasternack Enterprises, Inc.
Continuously variable attenuators from Pasternack are available in 50 Ohm impedance and with SMA connectors. SMA continuously variable attenuators have RF db attenuation values that range from 7 dB to 40 dB. The frequency range of our continuously variable attenuators is from 1 GHz to 18 GHz. This variable attenuator product line includes low to high power attenuators which have the power handling up to 5 Watts.Variable attenuators from Pasternack include female genders and can be bidirectional, depending on the power rating. Our continuously variable attenuators are manufactured to precise industry specifications and the bodies are constructed of. Pasternack commonly uses Pi attenuators or Pi pads for its continuously variable attenuator designs.
-
Analog Devices Inc.
Analog Devices is a leader in Class-D audio amplifiers and audio signal processing, and we deliver audiophile-level performance with our proven analog and digital technology. We offer a wide range of audio amplifiers, including industry-leading microphone preamps, microphone drivers, line drivers, and receivers. Our Class-D amplifiers, in particular, are among the lowest power and lowest distortion in the industry. Our portfolio includes Class-A, Class-B, and Class-D audio amplifier offerings, along with a breadth of power ICs. Analog Devices amplifier products have been used in many high volume consumer products where the highest audio quality is expected. The lowest power consumption also enables this performance in many battery powered applications as well.
-
MRS-26D -
Hangzhou Huatai Optic Tech. Co., Ltd.
*Ultra low noise push-pull technology *Band width of 2.7 GHz* 46dB CNR (typ.) for NISC with OMI = 4% at –8dBm optical input power @ 1550nm* 20dBmV RF output level (-5dBm,1550nm,OMI=4%)* Very low intermodulations *Low power consumption *Small package with single-mode fiber pigtail *Integrated optical demultiplexer (WDM filer) for RF overlay applications *Monitor voltage output and output disable input
-
CCI
*CCI DAS Trays provide a common connection point to the DAS system for multiple BTS's*Modular design allows support for bands from 700MHz to 2700 MHz*Independent level control for each BTS for adjusting TX & RX power*Easy optimization features including separate Uplink and Downlink control*Can support both 0 dBm and +30 dBmDAS TX inputs (high and low power)*Supports NIMO and SIMO configurations
-
MGS-402 -
Bacharach, Inc.
Bacharach’s MGS-402 Gas Detection Controller centralizes the status of up to two gas detectors, provides a complete package for your safety compliance application. On the front panel of the MGS-402 a bank of LEDs corresponds to each connected gas detector; showing power, alarm status and fault indicators. The MGS-402 can provide the power requirements for to up to two gas detectors, which can be daisy-chained with Modbus communication to each gas detector; simplifying and reducing the cost of installation.
-
Boson -
Teledyne FLIR
Boson longwave infrared (LWIR) thermal camera cores set a new standard for size, weight, power, and performance. Imagine your next big idea, and bring it to life with Boson. FLIR’s XIR™ expandable infrared video processing architecture gives Boson advanced image processing, video analytics, peripheral sensor drivers, and several industry-standard communication interfaces that make it easy to integrate while keeping power consumption low.
-
Elcontrol Energy Net S.r.l.
NanoVIP® ONE™ is a modern power quality analyzer equipped with all the functions necessary for measuring and monitoring both electricity consumption and the main power quality parameters.It can be used on single-phase and three-phase balanced networks in low and medium voltage as well as on DC systems.Particularly compact in size, it uses commercial AA batteries (rechargeable or not), has a considerable internal storage capacity (4Gb) and a graphic display.An affordable analyzer but suitable for professional use.
-
Radiall s.a.
Radiall's comprehensive product range of outdoor connectors are designed for severe outdoor conditions, mainly in wireless telecom infrastructure applications. The outdoor connector range includes high power RF coaxial connectors used for the microwave link between antenna and radio units, and innovative multi-signal I/O solutions for optical, Ethernet, power or coaxial links between radio equipment and backhaul networks. These outdoor connectors are also used in many industrial applications.
-
Procter & Chester Measurements Ltd
Radio Telemetry: A transmission of data from a remote source via a radio to a receiving station for recording and analysis. Inductance: A contactless method of supplying power to (in this case) a strain gauge bridge. The signal is then transmitted back to the electronics. Slip Ring: Consists of a conductive band mounted on a shaft and is insulated from it. The wheatstone bridge is connected to the bands (usually four off). Fixed brushes or contacts make contact on to the bands to transfer power to the bridge and signal back to the static instrumentation.
-
PGY-RFFE-EX-PD -
Prodigy Technovations Pvt. Ltd.
RFFE Protocol Analyzer (PGY-RFFE-EX-PD) is the Protocol Analyzer with multiple features to capture and debug communication between host and design under test. The RF Front-end control interface (RFFE) Serial bus interface is emerging as a chosen for controlling RF frond end devices. There are variety of front end devices such as Power Amplifiers (PA), Low-Nose Amplifiers (LNA), filters, switches, power management modules, antenna tuners. It is widely used in mobile devices.
-
Zebra Technologies Corporation
For today’s enterprises, IoT is no longer coming – it’s here and is pushing data processing power to the individual employee devices at the edge of your network. Being able to harness the power of edge-data is critical to maintain a competitive position within your industry. Whether it's understanding operational utilization, maximizing predictability and uptime, or simply unlocking the data of your edge devices, Zebra’s portfolio of services provides expertise every step along the way.
-
3206G -
Radian Research, Inc.
The Model 3206G Meter Warm-Up Station for AMR Modules has been specifically designed for meters that utilize the DCSI TWACS™ power line carrier communications module. Additionally, this versatile unit includes voltage output and voltage input connections that allow you to test additional brands of power line carrier modules when using the manufacturer’s supplied module. The Model 3206G can even be used as a simple meter warm-up station.
-
Arbin Instruments
Arbin's Regenerative Battery Testing (RBT) series is designed for testing high power battery packs. Today's applications like electric vehicles, military technology, and stationary grid storage demand high-reliability and safe testing environments. The latest generation of Arbin's RBT series has improved thermal management, redundant microcontrollers to help ensure failsafe testing, and built-in UPS to help ensure proper shutdown sequence in the case of input power failure.
-
Omron Industrial Automation
*Over 20 years of history in Power Monitoring Technology.*Compact with multi-circuit capabilities (up to 4 circuits connected to one unit).*Solve design, installation, wiring, and commissioning issues with only one model.*IEC 62053-22 accuracy class 0.5S*Push-in plus technology for easy wiring*Automatic LED and acoustic alarm in case of incorrect wiring*Large, easy-to-read, white LCD.*DIN rail mounting*Bi-directional power measurement
-
ExpressBox 2200 -
Wuntronic GmbH
Precision engineered to Magma’s mission critical standards for performance and reliability, ExpressBox 2200 features three (3) full-length, full-height PCIe slots and flexibility with eight (8) 2.5-inch SATA/SAS HDD or SSD hard drive bays. Designed with your workstation in mind, the EB2200 has a rack-mountable aluminum chassis for integrated removable storage expansion, a 520-watt fanless power supply, auxiliary power, and features Magma’s exclusive quiet cooling control.
