Showing results: 6811 - 6825 of 11167 items found.
-
LX-PDU-03-63A-NA -
LXinstruments GmbH
By using the power distribution unit (PDU), you simplify the ordering process with only one device required. Very high flexibility of the device through modular configuration. Comprehensive documentation through operating instructions, wiring plans and CE declaration of conformity. Due to the predominantly pluggable connections, integration and installation are extremely easy. Accessories, options and extensions are available.
-
VME8008X -
CAEN S.p.A.
The Model VME8008X is a 8 slot VME crate, suitable for 6U x 160mm boards, with VME64X compliant backplane. The Unit is powered by 100 – 240 Vac (50 – 60 Hz). The power distribution is 25A@+5V, 10A@+12V, 10A@-12V, 25A @ +3.3V. The VME8008X provides Automatic daisy chain and supports Chained Block Transfer (CBLT).
-
PMC-MC-X2-28 -
Dynamic Engineering
PMC-MC-X2 adapter/carrier/motherboard provides the ability to install up to 2 (two) PMC cards into a small enclosure. PMC-MC-X2 has one PMC card mounted front and one rear to create a compact arrangement with 2 PMC positions. The carrier provides power supplies for the +5, +3.3, +12, and minus 12 from a reference supply.
-
DSPH -
Computer Conversions Corporation
The DSPH Series High Power Digital to Synchro Converters, are proven, high efficiency, low cost, compact, reliable solid state synchro drivers; designed for demanding Naval/Maritime, Aircraft, fire control and Radar/Antenna related, applications. They are commonly used on synchro based data transmission, retransmission, simulation, and instantaneous absolute position indicating and active control systems.
-
LMS-3000 -
Lisun Electronics Inc.
• Measure and display the relative spectral power distribution (UV-VIS-NIR) P(λ), chromaticity coordinate, correlated color temperature, rending index, color difference, peak wavelength, luminous flux, luminous flux efficiency and photometry parameters of light source and light material under the control of general PC. • Automatically adjust high-voltage, it not only shortens the measurement time, but also reduces the wear and tear of the instrument • Simultaneously measure the temperature in both environment and integrating sphere to make the data more visually and reliably • Figure of chroma and color difference in test report can be exchanged freely • Color display and print. The relative spectral power distribution (UV-VIS-NIR) P(λ), reports both in English. RS-232-C interface, compatible with all kinds of computer • LSP-500 AC Power source PC RS-232-C interface. compatible with all kinds of computer • Range of wavelength: 380nm～780nm(Special:200nm～780nm) • Accuracy of wavelength: ±0.2nm • Repeatability of wavelength: ±0.1nm • Accuracy of chromaticity coordinate: ±0.0003(under standard illuminate A) • Spectrum sample interval: 5nm(Special order:1nm) • Luminosity linearity: 0.3% • Accuracy of luminosity: 1 class • Correlated color temperature measure range: 1500K～25000K • Accuracy of CCT: ±0.3%(under standard illuminate A) • Accuracy of rending index: ±(0.3%rd±0.3) • Environment temperature measure range: -10℃～80℃ • Temperature measure range(In sphere): -10℃～100℃
-
LEDRACK-100W192P -
Lisun Electronics Inc.
• Application range: LED driver and multi channel driver power aging. It has equipped with computer operation and monitor system. The working condition can be set by the computer, and the computer will record real time data to do statistical analysis. • The parameters of load can be set freely on the software, to monitor the real time voltage, current, and power etc • Load mode: CC, CV, CR, CP, and LED • Aging Control System includes: ON/OFF control signal output; Signal of relay switch control; K type thermocouple temperature acquisition • The channels are parallel connected under arbitrary load mode, which can allow product power expansion • The LED Driver Aging rack will design according to customer’s LED driver power and aging quantity per time • Automatic current switching function (optional) • AC power meter to measure modules, and test power input characteristics (optional) • Temperature monitoring function at product zone (optional) • PWM dimming and two sets of logic control signal function (optional)
-
DCZCT-20M -
MULTI MEASURING INSTRUMENTS Co., Ltd.
*DC earth fault measurement for solar power system*Least affection from the magnetization of core and temperature fluctuation*DC leakage current measurements*Current measurements for small DC motor*Convenient ＋5V single polarity power supply
-
EL08-460M -
Manatronics Pty Ltd
For High Voltage UPS Battery Testing and Power Supply testing. This particular Load has been designed to operate with UPS Battery Systems and Telecom Rectifiers and Power Supplies with output Voltages in the range of 307V to 460V and is extremely cost effective.
-
HD Power Test Equipment Co.ltd
Battery Discharge Charge Tester is mainly used for the charge test of the lead-acid battery of the backup power supply in the telecommunications, mobile, substation, railway transportation and pertrochemical industry power DC industries. It can proceed the discharge and charge for the batteries to extend the lift-time.
-
772D -
Keysight Technologies
The Keysight 772D is a high-performance, dual-directional coupler designed for broadband swept measurements in the 2 to 18 GHz range. This coupler can be combined with Keysight power sensors and power meters for reflectometer applications. Forward and reverse power measurements on transmitters, components, or other broadband systems are made simpler using the Keysight 772D. The broadband design allows the use of a single test setup and calibration for tests spanning the entire 2 to 18 GHz range.
-
CPM-80 -
Chuan Sheng Electronics Co., Ltd.
CPM-80 multifunction power analyzer provide high accuracy single phase and three-phase energy measuring and displaying, energy accumulating, power quality analysis, data logging and data communication. CPM-80 series meters are able to measure bidirectional, four quadrants kWh and kVarh. It provides maximum/minimum records for power usage and power demand parameters. Hardware standard built in a RS485 Modbus communication port , 4 Digital inputs, 2 Relay outputs, LCM and 2MB flash for data-logging. In addition , also provide TOU , voltage and current THD, harmonics up to the 63rd and auto wiring change via software .
-
AFV-P -
Intepro Systems
Intepro’s AFV-P Series is a programmable AC/DC output power source with precision measurement and control. This compact power source comes in four power levels, 600VA, 1250VA, 2500VA and 5000VA, providing clean power with distortion less than 0.3% at 40-100Hz. The AFV-P series delivers output voltage from 0 to 310VAC and frequency from 40 to 500Hz or 15 to 1000Hz with the high frequency option. It is ideal for commercial, defense and aerospace test applications from design verification, quality assurance, ATEs. The AFV-P Graphical Users Interface software makes it easy to setup complex testing of the AC input to the UUT.
-
LEC-iMX6R2 -
ADLINK Technology Inc.
The SMARC ("Smart Mobility ARChitecture") is a versatile small form factor computer Module definition targeting applications that require low power, low costs, and high performance. The Modules will typically use ARM SOCs similar or the same as those used in many familiar devices such as tablet computers and smart phones. Alternative low power SOCs and CPUs, such as tablet oriented X86 devices and other RISC CPUs may be used as well. The Module power envelope is typically under 6W. The Modules are used as building blocks for portable and stationary embedded systems. The core CPU and support circuits, including DRAM, boot flash, power sequencing, CPU power supplies, GBE and a single channel LVDS display transmitter are concentrated on the Module. The Modules are used with application specific Carrier Boards that implement other features such as audio CODECs, touch controllers, wireless devices, etc. The modular approach allows scalability, fast time to market and upgradability while still maintaining low costs, low power and small physical size. To stress on its low power consumption feature, ADLINK has named SMARC products as LEC (Low Energy Computer on module) series.
-
National Technical Systems
Fluid power systems play a critical role in many industries, and are one of the three major forms of power transmission along with electrical and mechanical power systems. In many cases, however, mechanical and electrical methods cannot provide a practical power transmission solution. In these cases, fluid power (whether hydraulic or pneumatic) is often used because it can deliver linear and rotary motion with high force and torque within a smaller, lighter package than is possible with other forms of power transmission. Some of the most common applications of hydraulic systems are in heavy construction and off-highway equipment. Other applications can be seen in aircraft, mass transportation systems (such as trains), construction, mining, agriculture, waste reduction, and utility equipment. The various components (such as valves, actuators, cylinders, accumulators, etc.) that make up these systems must perform reliably and have a reasonable life span. Only a thorough test program carried out under simulated field use conditions can insure that any component part or assembly will meet its original design goals for performance, reliability and longevity. Many internationally recognized organizations have published test standards that apply to hydraulic/pneumatic and fluid power systems and components. Some of these organizations are:
-
IS-*MT -
Lisun Electronics Inc.
According to requirement of IEC standards, the standard test temperature is 25℃, but high power lamps such as HID lamps and LED outdoor luminaires will produce a lot of heat during the test, thus the temperature inside the integrating sphere can not meet the requirements of IEC standards. Lisun Group designed the Constant Temperatured Integrating Sphere which allows the lamp was tested in a constant air temperature.
