Showing results: 691 - 705 of 723 items found.
-
PI-41401 -
Pulse Instruments
The PI-41401 is a four channel Clock Driver card capable of operating up to 140 MHz at 3V and 100 MHz at 5V amplitudes into a 50 Ohm load. The PI-41401 has a clock rate of 90 MHz at an amplitude of 5 volts into a 1-MOhm load. Into a high impedance load the output voltage range is from –5 volts to +8 volts with the pulse amplitude ranging from 0V to 9V. When driving a 50 load the voltage range is –2.5 volts to 4.0 volts with the pulse amplitude ranging from effectively 0V to 4.5V. Each channel has a common edgespeed control to vary the rising and falling edges of the output waveform. The adjustable slew rate range, for any amplitude, is the minimum edgespeed of that amplitude times 5. The output pulse amplitude and the load being driven determine the range of variability.
-
LR Environmental Equipment Co. Inc.
LR/RAD Drop Testers are available to simulate the impact a package would encounter during handling and shipment. The machine is air actuated to provide a reliable long life. Drop height ranges from 12-60 inches.The Drop Tester is supplied with a variety of standard features to earn its reputation as the industry standard: motor hoist with hand held control box to automatically raise and lower drop arm with package in place, Microswitch to preset drop height for repeatable drops, drop height indicator, remote hand switch actuated and a one inch vertical drop prior to drop arm swing to insure that package is not subject to rotation. LR/RAD Drop Testers are designed so packages may be released from any angle and be assured of landing in the same position. Special fixtures are available to allow for corner and edge drops.
-
781260-01 -
NI
6.6 GHz PXI Vector Signal Analyzer - The PXIe‑5663E offers wide instantaneous bandwidth and supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. You can use a PXIe‑5663E as either a spectrum analyzer or vector signal analyzer, and you can use it with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5663E can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5663E provides a low-cost solution to high-performance RF measurements.The PXIe-5663E comprises the following modules:• PXIe-5601 RF Signal Downconverter• PXIe-5622 IF Digitizer• PXIe-5652 RF Analog Signal GeneratorThere is no physical device named "PXIe-5663E".
-
781260-02 -
NI
6.6 GHz PXI Vector Signal Analyzer - The PXIe‑5663E offers wide instantaneous bandwidth and supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. You can use a PXIe‑5663E as either a spectrum analyzer or vector signal analyzer, and you can use it with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5663E can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5663E provides a low-cost solution to high-performance RF measurements.The PXIe-5663E comprises the following modules:• PXIe-5601 RF Signal Downconverter• PXIe-5622 IF Digitizer• PXIe-5652 RF Analog Signal GeneratorThere is no physical device named "PXIe-5663E".
-
781339-03 -
NI
6.6 GHz PXI Vector Signal Analyzer - The PXIe‑5663E offers wide instantaneous bandwidth and supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. You can use a PXIe‑5663E as either a spectrum analyzer or vector signal analyzer, and you can use it with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5663E can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5663E provides a low-cost solution to high-performance RF measurements.The PXIe-5663E comprises the following modules:• PXIe-5601 RF Signal Downconverter• PXIe-5622 IF Digitizer• PXIe-5652 RF Analog Signal GeneratorThere is no physical device named "PXIe-5663E".
-
781259-01 -
NI
6.6 GHz PXI Vector Signal Analyzer - The PXIe‑5663E offers wide instantaneous bandwidth and supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. You can use a PXIe‑5663E as either a spectrum analyzer or vector signal analyzer, and you can use it with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5663E can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5663E provides a low-cost solution to high-performance RF measurements.The PXIe-5663E comprises the following modules:• PXIe-5601 RF Signal Downconverter• PXIe-5622 IF Digitizer• PXIe-5652 RF Analog Signal GeneratorThere is no physical device named "PXIe-5663E".
-
781339-04 -
NI
6.6 GHz PXI Vector Signal Analyzer - The PXIe‑5663E offers wide instantaneous bandwidth and supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. You can use a PXIe‑5663E as either a spectrum analyzer or vector signal analyzer, and you can use it with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5663E can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5663E provides a low-cost solution to high-performance RF measurements.The PXIe-5663E comprises the following modules:• PXIe-5601 RF Signal Downconverter• PXIe-5622 IF Digitizer• PXIe-5652 RF Analog Signal GeneratorThere is no physical device named "PXIe-5663E".
-
781259-02 -
NI
6.6 GHz PXI Vector Signal Analyzer - The PXIe‑5663E offers wide instantaneous bandwidth and supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. You can use a PXIe‑5663E as either a spectrum analyzer or vector signal analyzer, and you can use it with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5663E can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5663E provides a low-cost solution to high-performance RF measurements.The PXIe-5663E comprises the following modules:• PXIe-5601 RF Signal Downconverter• PXIe-5622 IF Digitizer• PXIe-5652 RF Analog Signal GeneratorThere is no physical device named "PXIe-5663E".
-
781339-02 -
NI
6.6 GHz PXI Vector Signal Analyzer - The PXIe‑5663E offers wide instantaneous bandwidth and supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. You can use a PXIe‑5663E as either a spectrum analyzer or vector signal analyzer, and you can use it with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5663E can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5663E provides a low-cost solution to high-performance RF measurements.The PXIe-5663E comprises the following modules:• PXIe-5601 RF Signal Downconverter• PXIe-5622 IF Digitizer• PXIe-5652 RF Analog Signal GeneratorThere is no physical device named "PXIe-5663E".
-
PCI104 -
Vadatech Inc
The PCI104 is a PCIe carrier for PCI Mezzanine Cards (PMC) or Processor PCI Mezzanine Cards (PrPMC). The PCI104 carrier allows simplified testing of PMC/PrPMCs and their associated PMC I/O Modules (PIMs) by using a PC environment during board development or deployment. The PCI104 can also reduce the costs of manufacturing PMC/PrPMCs by allowing manufacturers to use off-the-shelf PCs for functional testing. The PCI104 converts the PCIe x4 edge connection to PCI-X via a PCIe to PCI-X bridge. The trace lengths to the PMC/PrPMCare kept to a minimum so the PMC/PrPMC can run with a133MHz PCI-X clock speed. The J4 connector of the installed PMC/PrPMC is routed to a 96-pin DIN connector per theVITA-35 specification. The PCIe to PCI-X bridge can run in either transparent or non-transparent mode and can also operate in forward or reverse mode. The PCI104 has a fan mounted on the board to cool the PMC/PrPMC. The fan can easily be removed for testing and probing of hosted card.
-
PCI102 -
Vadatech Inc
The PCI102 allows testing of AMC.1, AMC.2 and AMC.3 modules in a PC environment during development and manufacturing; reducing the costs associated with maintaining different platforms. The PCI101 is a PCI-X edge style carrier with PCIe x4 lanes going to the AMC module. The AMC.1 module connects to the host PC’s PCI-X bus via a PCI-X to PCI ebridge. The AMC.2 module’s GbE ports are routed to RJ-45s. The AMC.3 differential pairs are routed to two SATA connectors. ThePCI102 is available with an optional VT001 IPMI controller which can test the AMC IPMI management functionality. The dual I2C bus connectors allow for connecting any I2C bus to any other I2C bus as well as being able to debug and monitor the I2C bus traffic. Provides two current sense resistors to measure the payload power as well as the management power of the AMC. The PCI102 can be powered on the bench without the host PC.
-
PCI113 -
Vadatech Inc
PCI113 is VadaTech second generation PCIe expansion module. The PCI113 is a high-speed 20Gbps bridge from the host PCIe bus to VadaTech’s carrier and Rear Transition Module (RTM) products such as the ATC104/114/118/117/119, ART114, μTCA chassis, etc. The different carriers host different I/O modules such as PMC/PrPMC, AMC, PCI-X and PCIe edge modules. This concept allows any of the available I/O modules in these standard form factors to be integrated quickly and easily into an AdvancedTCA or μTCA subsystem. The PCI113 allows expansion among multiple μTCA chassis or expansion into other chassis that are not ATCA or μTCA based.The PCI113 is a single module PCIE based on the PCISIG specification. The PCI113 provides a PCIe x4 link infiber/copper via front panel QSFP. The dual front I/O allows expansion into two separate systems independently. The upstream port must not have spread spectrum PCIe clock enabled.
-
Konica Minolta Sensing Americas, Inc
To measure light radiation’s spectral characteristics, Instrument Systems optical spectroradiometers are the instruments of choice. Instrument Systems has a variety of optical spectroradiometers to meet any user’s needs or budget. Instrument Systems Spectrometers mainly measure UV-VIS spectroradiometry, luminous flux, LED production and LED radiation levels. More importantly, they provide these measurements at a fast rate, gathering data very quickly and efficiently. A number of models come with innovative features that allow the systems to be used universally in a broad range of applications and functions. These systems conveniently change into spectroradiometers when users attach absolute calibration and optical probes. It’s critical that these units maintain a high degree of accuracy and quality in order to return precise calculations of colorimetric, photometric and radiometric data through the built-in software. For these and other reasons, Instrument Systems continues to expand the leading edge of technology by committing the majority of its Research & Development work to this field.
-
NA850 -
Axiomtek Co., Ltd.
The NA850 offers cutting edge performance for networking applications with dual high performance 12-core Intel® Xeon® E5-2600 V3 series processors and Intel® C612 chipset, 16 high bandwidth DDR4 memory slots and two hot swappable 3.5” SATA HDD bays. For greater flexible and easy maintenance, the NA850 can be fitted with up to five Ethernet modules, supporting up to 42 Gigabit LAN ports or 20 10GbE LAN ports. Two PCIe x16 standard expansion slots are available for optional network security cards. The superior network appliance platform also supports the Intel® Data Plane Development Kit (Intel® DPDK), a set of software libraries that can improve packet processing performance by up to ten times. It could achieve over 80 Mbps on a single Intel Xeon processor and double with a dual-processor configuration. With its friendly design and high capacity, this powerful network appliance is suited for IDS/IPS, VPN, content filtering, UTM, network security applications, and cloud computing solutions.
-
CAPA13R -
Axiomtek Co., Ltd.
The CAPA13R is powered by the onboard AMD RYZEN™ Embedded V1807B/V1605B processor with Radeon™ Vega graphics. The 4K embedded board is well-suited for graphics-intensive applications such as medical imaging, video surveillance, 3D simulators, optical quality control, digital signage, kiosks/POI, thin clients, and more. The integrated AMD RadeonTM RX Vega graphics with support of DirectX 12 and OpenGL 4.5 marks the cutting edge of embedded graphics. The CAPA13R can deliver truly impressive user experiences and outstanding 3D graphics quality through two HDMI, one DisplayPort and one LVDS interfaces. Its onboard CPU is attached on the rear side of the board, which can aid with heat dissipation and offers flexibility for easy system integration and minimum maintenance. Moreover, the CAPA13R offers multiple expansion interfaces with one M.2 Key E slot for wireless modules and one M.2 key B slot for storage cards. One 260-pin SO-DIMM socket on the CAPA13R supports up to 16GB of DDR4-2400 (V1605B) and DDR4-3200 (V1807B) memory. The system has a +12V DC power input.