Showing results: 391 - 405 of 580 items found.
-
2800 Series -
MicroSense, LLC
Many sensor heads, or probes, are available for use with our 4800 series and 8800 series capacitive position sensor. The resolution of our capacitive position sensors is determined by a combination of the active sensing area of the probe, the measurement range, and the measurement bandwidth of the electronics unit (demodulator). Please refer to the Model 4810 data sheet for complete details on probe selection, including mechanical dimensions of our standard probes.
-
Integris 3000 -
Absolute Analysis
Most modern cell tower network configurations place the Remote Radio Head (RRH) at the top of the tower and the baseband unit(BBU) at the bottom of the tower. While this configuration is advantageous for both computational efficiency and mitigation of RF loss across the cable, it means the only place along RF can be accessed is at the top of the tower. This forces field technicians to have to climb the tower to measure and debug RF noise problems.
-
ADXL377 -
SparkFun Electronics
The ADXL377 is a small, thin, low power, complete 3-axis accelerometer with signal conditioned analog voltage outputs that has a full-scale range of ±200g for measuring more extreme changes in motion, shock or vibration. This board has broken out all the pins you’ll need to get the necessary data from the accelerometers. The breakout is perfect for applications like concussion and head trauma detection or high force event detection.
-
Mk4 -
ThermoWorks
With full readings in only 2 to 3 seconds, the Super-Fast® Thermapen is the world’s best in speed and accuracy. Advanced technology makes the new Thermapen Mk4 even more intuitive than previous models. Hold it in any direction and the display automatically rotates right-side-up so you can read it in any position—in either hand, straight up or down; read temperatures without cocking your head.
-
EFX6000 -
Summit Technology, Inc.
The EFX6000 is a flexible AC current clamp utilizing the Rogowski principle. It can be used to measure currents from 1 amp to 6000 Amps in 2 auto-ranges, over a wide frequency range to 10kHz. The flexible and lightweight measuring head allows quick and easy installation in hard to reach areas, around large conductors and where access to confined or tight spaces is a problem. It requires no batteries or external power supply.
-
PCE Instruments
An adhesion tester measures the force required to detach a coating from a substrate. Often called a pull-off adhesion tester or peel tester, an adhesion tester applies a large amount of force to evaluate a coating's bond strength. When measuring peel force or adhesiveness, the nature of the substrate's surface plays a significant role. However, a high-quality adhesion tester features a self-aligning measuring head to compensate for any surface irregularities.
-
Educated Design & Development, Inc.
1250 g body includes release mechanism and striking element guide.250 g striking element comes with cocking knob and hammer head, polyamide face, is hemispherical with a radius of 10 mm, has a hardness of HR85-100.60 g release cone with a 10N release force.Single Impact Force models range from a 0.2 J Hammer to a 2.0 J Hammer.Custom padded carrying case included.
-
SeaBat T20 MotionScan -
Teledyne Marine RESON B.V.
The SeaBat T20 MotionScan is a tilted head 350° rotational configuration based on the renowned and compact SeaBat T20 high-resolution multibeam echo sounder. Installed on a dredge barge the SeaBat T20 MotionScan will, literally at the push of a button, map the work progress in seconds – saving contractors both time and money. As a part of the modular SeaBat T-series, the T20 MotionScan can also easily be reconfigured to more traditional survey tasks.
-
PR-82 -
Dakota Ultrasonics
The PR-82 sonic tester has been modified for the automotive industry. This gauge is commonly used for measuring the thickness of cylinder walls, head ports, decks, tubing, body panals, and windshields. It also has the ability to scan the length of a part to find the the minimum thickness.The PR-82 is back-lit and the unit operates for up to 200 hours on a single set of batteries. It is protected by Dakota Ultrasonics 5 year limited warranty.
-
TCR-600 -
NAPSON Corp.
*Controlled Thermo-chuck (room temperature~600℃/less than 20 minutes)*600C compatible probe head with 1mm linear*Controlled with vacuum sensor, digital thermo-meter, vacuum gauge and gas flow meter*Temperature measuring accuracy:±(0.5% + 1℃)
-
MC388 -
Manncorp
The MC388 features four simultaneous heads with dual-vision alignment that can achieve placement rates of 10,500 CPH. When used as an inline machine, up to 192 Smart Feeder can be attached, providing a near-zero job changeover time. Plus, it has the huge placement area, high precision, and accuracy that users have come to expect from MC-series component placers. The MC388 is ideal for LED strips, drivers, or other large, high-component panels.
-
UWS -
Aeronautical & General Instruments Ltd.
Data from the mast-mounted (and virtually maintenance-free) anemometers is processed and used to drive full colour displays. The system calculates cross winds, head winds and tail winds, gusts and lulls and directional variation, as well as allowing for marked discontinuities. Instantaneous data may be displayed, as well as 2 minute and 10 minute averages. Systems can be supplied fully installed with comprehensive engineering and operator training, and post-installation support is available worldwide.
-
FanZ -
Zeus Numerix Pvt. Lmtd.
FanZ designs efficient high aspect ratio blades for axial fans. For the required head & flow conditions, FanZ calculates the span-wise variation of chord length & twist of the most optimal sectional profile. The software also predicts the off-design-performance and structural robustness of the blade. The output is in the form of ready to manufacture DXF format drawing files. More than a dozen customers use FanZ for the design of their cooling tower fans.
-
INN-8686-18-PRO -
INNOVENTIONS, Inc.
Your best option if you need to test a large volume of memory! The RAMCHECK LX DDR4 Pro 288-pin DIMM Adapter (p/n INN-8686-18-PRO) gives RAMCHECK LX users the power to test 288-pin DDR4 modules, including unbuffered (UDIMM), load-reduced (LR-DIMM) and registered modules (RDIMM), both ECC and non-ECC, that comply with JEDEC standards. It includes the DDR4 Series adapter and DDR4 Pro DIMM test head.
-
Model InstaTrans-XD -
Teledyne Analytical Instruments
This model utilizes a design to meet the requirements of NEMA-4(IP-66) levels as well as ATEX Zone 0/1/2 and FM/FMc Class I Div 1 approvals when used with select intrinsic safety barriers. In addition, the CSA approval extends to Class I Div 2 as a non-incentive device without the use of barriers. The transmitter head contains the electronics and user display interface including 4-button design to access functions.