Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
USB Data Communications Multiplexers
These USB multiplexers are ideal for the testing of multiple devices that use USB interfaces, allowing the test system to select one target device from many. The design is bi-directional to permit use as a multiplexer or de-multiplexer with no impact on performance and uses long lifetime electro-mechanical relays characterized for use in data communications systems.
-
product
DSP Based Serial Communication Board
CPCI-ISC8
The CPCI-ISC8 is an intelligent DSP based serial communication board. This 3U board is based on the CPCIIPC product and has been modified to remove the IPinterface and to support additional I/O features. The CPCIISC8 provides mechanical support and the electrical interfaces for an I/O mezzanine board. Multiple CPCI-ISC8 boards may be installed in a single system.
-
product
4/8-port Asynchronous Serial Communications Modules
cPCI-3534/3538-S
*32-bit CompactPCI, PICMG 2.0 Rev 2.1*Plug-and-play, IRQ & I/O address automatically assigned by PCI BIOS*4/8 asynchronized communications ports with intelligent buffer*Three RS-232 ports and one isolated RS-422/RS-485 port with 2500 VRMS isolation voltage for cPCI-3534, and eight RS-232 ports for cPCI-3538*Surge protector in TXD/RXD signal line
-
product
XMC - Module VITA61/42
XMC-1553-2-IO
The XMC-1553-2-IO-2 uses a DDC® Total-ACE® communication device as its 1553 bus controller, or as a remote terminal with concurrent bus monitor terminal. Dual controller has a dual redundant channel with built in transceivers and transformer. The controller has the capability to emulate up to 31 RT addresses simultaneously.
-
product
EFT Module for Teststand
The Electronics Functional Test (EFT) Module for TestStand provides out-of-the-box tools to speed up development of automated tests for electronic assemblies including PCBAs, subassemblies and final assemblies. Test engineers can develop, deploy and execute test sequences quickly and efficiently with minimal custom code development for a shorter time-to-solution.
-
product
Test Solutions
Our range of test solutions is far reaching, comprised of off-the-shelf test instruments and interfaces, standard automated test systems, and custom solutions for test, simulation, and training. Put our E2E focus and experience to work for you with these solutions: automated test equipment, maintenance trainers, and test management software.
-
-
product
Tactical Radio Test Set
CTS-6010
The CTS-6010 brings an entire test bench to your front lines. Enable your technicians to detect equipment faults and verify operational capabilities at the I- and O-levels, saving valuable diagnostic time and cost.
-
product
ESS Performance Test System
The Energy Storage System (ESS) Performance Test System is used to evaluate, test, and certify the performance of energy storage systems up to 2MW. The system is a configurable platform with over 200 channels of simultaneously measured AC and DC voltages and currents, environmental temperatures, airflow, and communications. Intuitive software provides real-time monitoring and analysis of power, energy and efficiency to adhere with industry standards. The test system interfaces hardware such as load banks, and controls the ESS to simulate utility applications such as peak shaving and frequency regulation.
-
product
Communications Test System for Frontline Diagnostics
CTS-2750
The CTS-2750 is designed using Astronics Test Systems’ proven Synthetic Instrumentation architecture. Featuring 23instruments, and both Automated and Standalone modes to test, record, and diagnose faults, the unit provides complete RF, Analog and Digital capabilities. The field-upgradeable, software-defined architecture features easy-to-use graphical user interfaces and enables testing with minimal operator intervention. Test Program Sets can be created easily using the included TestEZ® software suite.
-
product
Benchtop Communication Test System
ATS3000A
The ATS3000A is designed using Astronics Test Systems’ proven Synthetic Instrumentation architecture. Featuring 23 instruments, and both Automated and Standalone modes to test, record, and diagnose faults, the unit provides complete RF, Analog and Digital capabilities. The ATS3000A also includes the sophisticated IF and baseband I/Q Digital Signal Processing required for modern radios. The fieldupgradeable, software-defined architecture features easy-touse graphical user interfaces and enables testing with minimal operator intervention. Test Program Sets areavailable for a full range of tactical radios, or you can create new TPSs easily using the included TestEZ® software suite.
-
product
Military Communications Test
Astronics testers for military radios and wireless communications systems help you keep your most critical communications up and running smoothly. Write test program sets once and deploy them instantaneously everywhere – whether your test set is in the factory, at the depot, or in operation.
-
product
Radio Frequency, Communications, & Navigation Test Systems
Reduce testing time and costs with the Astronics radio test sets for use in military, avionics, and civil security industries.Available in commercial and military grades, these integrated test systems make it easy to develop test program sets and leverage them securely and instantly across all deployed testers at the factory, depot, and operational levels.
-
product
Communication Test System
CTS-2700
The CTS-2700 is designed using Astronics Test Systems’ proven Synthetic Instrumentation architecture. Featuring 23instruments, and both Automated and Standalone modes to test, record, and diagnose faults, the unit provides complete RF, Analog and Digital capabilities. The field-upgradeable, software-defined architecture features easy-to-use graphical user interfaces and enables testing with minimal operator intervention. Test Program Sets can be created easily using the included TestEZ® software suite.
-
product
Communications Test System for Frontline Diagnostics
ATS3000P
The ATS3000P is designed using Astronics Test Systems’ proven Synthetic Instrumentation architecture. Featuring 23instruments, and both Automated and Standalone modes to test, record, and diagnose faults, the unit provides complete RF, Analog and Digital capabilities. The ATS3000P also includes the sophisticated IF and baseband I/Q DigitalSignal Processing required for modern radios. The fieldupgradeable, software-defined architecture features easyto-use graphical user interfaces and enables testing with minimal operator intervention. Test Program Sets are available for a full range of tactical radios, or you can create new TPSs easily using the included TestEZ® software suite.
-
product
PCIe 5.0 Test Platform
PXP-500A
The Teledyne LeCroy PXP-500A Test Platform provides a convenient means for testing PCIe 5.0 cards with a self-contained portable and powered passive backplane. The PXP-500A provides power required for both cards under test.
-
product
PCI Express 5.0 Test Platform
Teledyne LeCroy’s PCI Express 5.0 Test Platform is part of a suite of tools that facilitates complete protocol testing of PCI Express devices up to and including version 5.0. The latest feature of the Teledyne LeCroy Test Platform is the addition of an integrated interposer, which eliminates the need for an external interposer. This innovation simplifies setup with fewer connection points and outboard devices, making analysis easier and more reliable than ever. In addition to using the Test Platform with the Exerciser, the user can connect two of their own devices and use the Test Platform as a PCIe 5.0 backplane and as an interposer to capture protocol traffic between the systems.
-
product
ARINC 818 Tester
iWave 3U VPX High-Speed Video/Data Processing Card is a rugged standalone module in the 3U VPX form factor, aimed for the high-speed data, video processing, and display applications is ideal for military, defense, and aerospace applications requiring an optimal balance of performance and power efficiency. iWave 3U VPX High-Speed Video/Data Processing Card is implemented using Xilinx Kintex-7 device architecture and has I/O interfaces including High speed 16 channels of transceiver interfaces capable of operating up to 6 Gbps data rate, Gigabit Ethernet, RS232, RS422, PCIe interface, Built-in health monitoring circuits, HDMI input, and output interfaces
-
product
Test System
BMS HIL
The BMS Hardware-in-the-Loop (HIL) Test System is a high performance platform providing all necessary input signals used for battery pack simulation. A real-time operating system executes complex cell and pack models commonly used for BMS algorithm development and firmware regression testing.
-
product
FADEC/EEC Test Platform
The FADEC/EEC Test Platform provides a hardware in-the-loop (HIL) closed-loop test environment for dynamic and maintenance testing of full-authority digital engine control (FADEC) and electronic engine control (EEC) units of both rotary- and fixed-wing airframes. The system simulates one or more turbofan engines, including its sensors and actuators for use with the most sophisticated FADECs and EECs on the market. The system delivers repeatable, cost-effective testing in a fraction of the time needed with typical in-house simulation test systems.
-
product
Flight Control System Test Platform
The Flight Control System Test Platform provides a hardware in-the-loop (HIL) closed-loop test environment for dynamic and maintenance testing of Flight Control Systems (FCS) of both commercial and military aircraft. The system simulates control surface activities from multiple combinations of rudder, flaps, elevator, aileron, and engine controls to the FCS. The system delivers repeatable, cost-effective testing in a fraction of the time needed with typical in-house simulation test systems.
-
product
Functional Test
xUTS
Extend test to encompass copious test points and DUT varieties along with real-time, hardware-in-the-loop and other state-of-the-art instrumentation. extendedUTS (xUTS) is a custom product for high complexity functional test. Configured for the unique needs of a class of devices under test (DUTs), the xUTS employs our universal test system approach that combines the best open platform instrumentation and software along with mass interconnect technology.
-
product
Functional Test
cUTS
Get the essentials of measurement automation to power tests of simpler PCBAs and subassemblies. compactUTS (cUTS) is a cost-effective platform for automating manual tests of devices with fewer than fifty cable-accessible test points in manufacturing environments with moderate production volume. DUT-specific electrically keyed cables make changeover quick and easy.
-
product
Functional Test
UTS
The UTS functional test system is perfect for electronics manufacturing operations that have a mix of products where operators load and unload devices under test (DUT) and routinely change out fixtures for each type of DUT.
-
product
Mixed Signal Battery Test System
The Mixed-Signal Battery-Test System is an automated test platform designed to meet today’s advanced battery test requirements. The platform is ideal for testing a range of battery cells and packs, and can be used in applications such as research and design, quality control, and end-of-line manufacturing. Its distributed architecture provides a scalable solution with configurable system components to accommodate specific applications.
-
product
Functional Test Fixtures
Reliable connections to device under test (DUT) test points are essential for robust functional test. Bloomy provides rugged fixtures and cable sets (ITAs) built for thousands and thousands of cycles in manufacturing environments. With the industry’s best mass interconnects and internal electronic keying, our fixtures are easy to change out and are automatically recognized by the test system.
-
product
Benchtop Automated Functional Test
midUTS
Combining bench-top portability with powerful automated test functionality, the midUTS is an extremely versatile yet cost-effective solution for your electronics functional test needs. Comprised of high-performance commercial-off-the-shelf (COTS) instruments, along with Bloomy’s medium-density signal-routing PCBAs, a built-in or USB-connected PC, and a pair of high-integrity, production-grade cables connected to an adjacent benchtop fixture, the midUTS can be used in engineering for PCBA bring up, as well as scaled to manufacturing to perform high-volume PCBA and sub-assembly functional testing. It is also ideal for depot diagnostic test, debug, and repair of field returns. The two mass-interconnected cables connect the midUTS to as many as 320 test points on the unit under test (UUT), supporting an extreme wide variety of products using bed-of-nails as well as cable-connected UUT test fixtures. Most importantly, the midUTS helps you automate sequences of functional tests using NI TestStand and the Bloomy EFT Module for TestStand. This ideal balance between powerful features and affordable cost allow you to automate earlier in the product development lifecycle, substantially increasing product quality and minimizing time-to-market!
-
product
Electronics Functional Test
Functional test for productive manufacturing. Manufacturers of products enabled by electronics must assure proper operation prior to shipment. Bloomy’s line of universal test systems are ideal for functional test of your PCBAs and subassemblies, from the simplest to the most complex. The UTS family of products combines high-performance test instruments, switching, power control and mass-interconnect hardware with our robust UTS software suite into a low-risk, cost-effective and powerful test solution for your device under test (DUT).
-
product
BMS Manufacturing Test System
The Battery Management System (BMS) Manufacturing Test System performs functional testing of product during end-of-line manufacturing. The system hardware includes all instrumentation to test a BMS, including multiple cell simulators, a mass interconnect for quick product transition and bed-of-nail fixtures to ensure less down time, higher throughput, and easy maintenance. The system application easily integrates into manufacturing processes, provides a method to test multiple product types, and optimizes tests to ensure only good product is released from manufacturing.
-
product
Environmental Control System Test Platform
The Airframe Environmental Control System Test Platform provides a hardware-in-the-loop (HIL) closed-loop test environment for dynamic and maintenance testing of cockpit and cabin environmental control systems for airframes. The system simulates a military or commercial airframe cabin, including sensors and actuators from the control system and the passengers. The system delivers repeatable, cost-effective testing in a fraction of the time needed with typical in-house simulation systems.
-
product
Battery Management (BMS) Environmental Test System
The BMS Environmental Test System is a configurable platform simulating the essential signals used by Battery Management Systems (BMS) and cell-monitoring modules with the ability to perform environmental testing on multiple BMS units simultaneously. The system implements single-point value testing to evaluate specific BMS functions such as cell over and under voltage scenarios, cell leakage current, lost communications, or faulty system IO.
