Showing results: 316 - 330 of 357 items found.
-
AMIC-30 -
Amperis sl
The AMIC-30 insulation tester is a small portable meter designed to measure insulation resistance in electrical and telecommunications installations, cables, motors, transformers and other equipment. The test voltage can be programmed in steps from 10 V to 1000 V. The instrument can measure both insulation resistance over a wide range (0,1kΩ...100GΩ), and insulation leakage current, capacitance and other parameters. All test results can be stored in the internal memory and sent to a computer via the included wireless USB receiver. The meters are supplied with rechargeable Ni-Cd batteries.
-
Keysight Technologies
Keysight's PNA-X is more than just a vector network analyzer. It is the world’s most integrated and flexible microwave test engine for measuring amplifiers, mixers, frequency converters, and other active devices. The hardware includes two internal signal sources, a signal combiner, S-parameter and noise receivers, pulse modulators and generators, and a flexible set of switches and RF access points. These hardware features provide a powerful core for a broad range of linear and nonlinear measurements, all with a single set of connections to your device under test.
-
GVS139B -
CRYSOUND
GVS139B Polarity tester adopts pulse test, which is not affected by environmental noises. It can quickly and automatically identify the positive and negative polarity of loudspeakers, headphones, televisions, stereos, speakers, and voice coil receivers. It is suitable for production lines. Meanwhile, you can use a foot switch to switch between an external sweeper, F0, and impedance meter. It is the most suitable for the full-featured detection of speakers on production lines.
-
GX6864 -
Marvin Test Solutions, Inc.
The GX6864 consists of (4), 2 x 16, 75 RF switch configurations that can be used as multiplexers or matrices. The switch card is an extended 6U PXI module with direct connection to the receiver interface. The inputs to the switch multiplexers are accessed via dedicated external connectors located on the switch module. Additional connections are provided to the GENASYS' internal 16 wire bus for low frequency and self test applications.
-
N5173B -
Keysight Technologies
Balance budget & performance to address parametric testing of microwave components & receiversPerform LO up conversion for microwave backhaul links or CW blocking for receiver testingMaximize test throughput with 600-s frequency switchingCharacterize microwave filters & amplifiers with the best combination of output power, low harmonics & full step attenuationUse as a high-stability system reference: the standard high-performance OCXO has an aging rate of 5x10-10 parts/day
-
S94610B -
Keysight Technologies
Digital Wideband Transceiver Analysis is an add-on software to Device Measurement eXpert (DMX) that adds cross-domain stimulus response measurements for digital/RF mixed-signal device characterization. Included Waveform Creator helps define digital IQ test stimulus waveforms that are used in the RF signal generators for receiver tests or downloaded to the digital-to-analog converters for transmitter tests. The DUT control is customizable to accommodate various data converters and transceiver types by defining device operation settings, transmit/receive switching, reading and writing digital IQ waveform from and to DUTs. Acquired RF or digital data is processed in the VNA’s applications for faster, accurate measurements and analysis.
-
PAMS & PAMS-C -
Praxsym
PAMS is a user-friendly, transmitter and receiver system that measures shielding effectiveness in RF shielded enclosures. Lightweight and compact, each PAMS unit measures approximately 12” x 5” x 5” and weighs 5.5 lbs., making PAMS ideally suited to field measurement tasks. Rugged construction insures instrument survivability in a field test environment. PAMS-C is a simple and efficient solution for quickly identifying shielding faults in an RF shielded enclosure. Cousin to the original PAMS used extensively by customers operating RF Shielded Enclosures, PAMS-C gives commercial end-users everything needed to measure shielding effectiveness levels of critical infrastructure - all with minimal or no interruption to normal operations.
-
SMBV100B -
Rohde & Schwarz GmbH & Co. KG
The state-of-the-art R&S®SMBV100B vector signal generator sets standards for its class. Ultra high output power, fully calibrated wideband signal generation and intuitive touchscreen operation make the R&S®SMBV100B ideal for all kinds of applications.Always in line with the latest major digital communications standards, such as 5G NR, LTE and WLAN, the SMBV100B is the preferred test solution for receiver and component characterization.The R&S®SMBV100B has many GNSS options that transform the instrument into a reliable, full-featured GNSS simulator. Advanced simulation capabilities can run realistic and complex yet repeatable GNSS scenarios under controlled conditions.
-
Y1800A -
Keysight Technologies
The RF transceiver kit consists of a transmitter unit and a receiver unit in superheterodyne architecture. The transceiver units are made up of various RF building-block modules such as filter, low noise amplifier, power amplifier, mixer and oscillator. The RF transceiver kit is controlled by a Windows-based Control Panel software via USB. A Measurement Automation Program is provided to demonstrate automated characterization and test of RF circuits. A signal generator and a spectrum analyzer are required to run this program.
-
SG1000B/PR1000A -
Praxsym
The SG1000 Signal Generator and PR1000A Preamplifier have been designed to simplify the measurement of shielding integrity in a shielded enclosure. When coupled with a high stability spectrum analyzer and an appropriate selection of test antennas, the SG1000/PR1000A combination can measure shielding effectiveness at all of the NSA 94-106 (supersedes NSA 65-6) defined test frequencies from 1 kHz to 10 GHz.The PR1000A amplifies the received signal from the test antenna and overcomes the high noise figure of the companion test receiver or spectrum analyzer. The PR1000A will ensure that the system noise figure will be less than 4.5 dB at all test frequencies from 1 kHz to 10 GHz. When used with a spectrum analyzer measurement bandwidth of 100 Hz, the system exhibits a sensitivity of -150 dBm at the test antenna output.To overcome high cable loss between the test antenna and the PR1000A assembly at 10 GHz, a remote low noise pre-amplifier (Praxsym PN 310-010091-001) is mounted directly onto the 10 GHz antenna.
-
81134A -
Keysight Technologies
When timing and performance requirements are critical, for example in high-speed serial bus applications like PCI Express or Serial ATA, its fast rise times and low intrinsic jitter allow the precise and in-depth characterization of devices, e.g. receivers or backplanes. On top of that, it allows to generate application-specific signal levels like pre- and de-emphasis (PCI Express) or squelch (Serial ATA). The Keysight 81134A lets you test your DUT instead of the pulse or data source!
-
M8296A -
Keysight Technologies
The Keysight M8296A is a four-channel, high-speed electrical digitizer module for the AXIe platform. It can synchronously sample up to four incident waveforms and is ideally suited to digitize the output signals from a dual-polarization coherent receiver. Keysight's vector signal analyzer and optical modulation analyzer software serves as the M8296A's user interface and enables a multitude of test and measurement tasks such as spectral analysis and digital demodulation for the analysis of signal quality metrics like error-vector magnitude. Furthermore, the sampled waveform can be stored and processed with the user's own tools (e.g. using Matlab). The modular approach allows users to combine the M8296A high-speed digitizer with other modules in one mainframe such as the M8292A modular optical modulation analyzer and the M8196A 92 GSa/s arbitrary waveform generator.
-
165 CB -
Standard Electric Works Co., Ltd
● 165 CB is an ideal tool which can test the correct pin configuration for different kinds of cables.● For testing: -RJ45/RJ11 -USB -COAX -BNC cable -Multi-wire cable● Auto-scan and manual-check function● Buzzer sound warning for wire status● 2 LED module indicators on the master unit which can do both of transmitter and receiver functions for RJ45/RJ11 cable testing. Users don't need to use the receiving unit.● 165 CB provides a variety for checking cable continuity, open status, short status and miss-wired. ● Ground (shielded ) wire test.● LED indication for wire status.● Power source : 9V battery
-
Inframet
Laser systems (laser range finders, laser designators, laser receivers, laser trackers, laser pointers) are one of crucial technologies for defense/security sector. Laser systems have also found mass applications outside defense sector. Testing laser systems is needed for both manufacturers, maintenance workshops and final users for a set of different and important reasons. Hi-tech test equipment can help significantly in manufacturing, maintenance, training, purchase optimization, and optimal use of night vision devices.
-
EA923 -
6TL Engineering
- Test handler 6TL36 Plus.- Dual line (bypass)- 1096 x 1875 x 1851mm [WxDxH]- Expandable to form a group with several 6TL36 modules (adapt line to production volumes).- ICT, FCT with RF, ISP or Combined test (ICT+FCT)- Servocontrolled DUT stop (stopper-less system)- Exchange time 3,2s- Max. PCB dimension 600x450mm- 19” rack space for instruments integration: 28UH- Receiver 25 slots in probe plate + 4 slots in push plate- Automatic Conveyor width adjustment- Optional Return Conveyor- High dynamics conveyors (1500 mm/s)- 90mm Top-30mm Bottom Component clearance- SMEMA and Hermes standard- CE
