Filter Results By:
Products
Applications
Manufacturers
Ethernet Test
Evaluation of a packet based ethernet network's wiring and signaling.
- Pickering Interfaces Inc.
product
PCI Fault Insertion Switch Range for Differential Serial Interfaces
50-200/201
Pickering Interfaces, a leading supplier of modular signal switching for electronic test and simulation, is expanding its range of PCI Fault Insertion switching with the introduction of two new modules (models 50-200 and 50-201) designed for use with differential serial interfaces. PCI Fault Insertion Switch Cards for Differential Serial InterfacesThe new modules include the Differential PCI Fault Insertion Switch (model 50-200) which is designed for lower data rate serial interfaces such as CAN and FlexRay, and the High Bandwidth Differential PCI Fault Insertion Switch (model 50-201) which is designed for higher data rate serial interfaces such as AFDX and 1000BaseT Ethernet. Each module allows the introduction of fault connections that include data paths open, data paths shorted together, and data paths shorted to externally applied faults such as power supplies and ground. The software driver defaults to a protective mode where conflicting faults are prevented to avoid accidentally shorting unintended paths, such as power to ground. A separate mode allows complete freedom in setting fault patterns.
-
product
PXIe-8521, 4-Port, 100BASE-T1 PXI Automotive Ethernet Interface Module
786771-01
PXIe, 4-Port, 100BASE-T1 PXI Automotive Ethernet Interface Module - The PXIe-8521 is a 100BASE-T1 unshielded twisted pair (UTP) Automotive Ethernet interface for developing applications with the NI‑XNET driver. The PXIe-8521 is ideal for developing applications that require … Automotive Ethernet to test and validate automotive electronic control units (ECUs). The interface provides up to four independent endpoints or up to two network terminal access points (TAPs). It features onboard hardware timestamping and can act as up to four separate 802.1AS masters or slaves, which allows it to synchronize with an external network as well as the rest of a PXI system. The PXIe-8521 also provides LEDs on the front panel so that you can monitor the network link and activity.
-
product
PXIe-8523, 4-Port, 100/1000BASE-T1 PXI Automotive Ethernet Interface Module
787311-01
PXIe, 4-Port, 100/1000BASE-T1 PXI Automotive Ethernet Interface Module - The PXIe-8523 is a 100/1000BASE-T1 unshielded twisted pair (UTP) PXI Automotive Ethernet Interface Module for developing applications with the NI‑XNET driver. With this hardware, you can develop applications … that require Automotive Ethernet to test and validate automotive electronic control units (ECUs). The PXIe-8523 provides up to four independent endpoints or up to two network terminal access points (TAPs). It features onboard hardware timestamping and can act as up to four separate 802.1AS masters or slaves, so it can synchronize with an external network as well as the rest of a PXI system. The PXIe-8523 also provides LEDs on the front panel to help you monitor the network link and activity.
-
product
PXIe-8623, 4-Port, 100/1000BASE-T PXI Automotive Ethernet Interface Module
787992-01
PXIe, 4-Port, 100/1000BASE-T PXI Automotive Ethernet Interface Module - The PXIe-8623 is a 100/1000BASE-T unshielded twisted pair (UTP) PXI Automotive Ethernet Interface Module that helps you develop applications with the NI‑XNET driver. With the PXIe-8623, you can develop applications that require Ethernet to test and validate automotive electronic control units (ECUs). The PXIe-8623 provides up to four independent endpoints or up to two network terminal access points (TAPs). It features onboard hardware timestamping and can act as up to four separate 802.1AS masters or slaves, making synchronization with an external network as well as the rest of a PXI system possible. Additionally, the PXIe-8623 features LEDs on the front panel to help you monitor the network link and activity.
-
product
PXIe-8522, 4-Port, 1000BASE-T1 PXI Automotive Ethernet Interface Module
787312-01
PXIe, 4-Port, 1000BASE-T1 PXI Automotive Ethernet Interface Module - The PXIe-8522 is a 1000BASE-T1 unshielded twisted pair (UTP) module for developing applications with the NI‑XNET driver. With this hardware, you can develop applications that require Automotive Ethernet to test … and validate automotive electronic control units (ECUs). The PXIe-8522 provides up to four independent endpoints or up to two network terminal access points (TAPs). It features onboard hardware timestamping and can act as up to four separate 802.1AS masters or slaves, so it can synchronize with an external network as well as the rest of a PXI system. The PXIe-8522 also provides LEDs on the front panel to help you monitor the network link and activity.
-
product
10 Gbit Ethernet Card, PXIe Form Factor
ADQ10GBE
The ADQ10GBE module enables fast network connection from a cPCIe/PXIe chassis to an external host computer. It occupies a single slot in an 3U cPCIe/PXIe chassis and can be used with backplanes supporting up to x8 Gen2 PCIe. All necessary software drivers are included and can be installed on the PXIe controller. ADQ10GBE can be used under Windows 7 (32 or 64 bit), Windows 8 and 8.1, and Linux (native support or ixgbe source code).
-
product
PXIe-8234, 2-Port Gigabit PXI Ethernet Interface Module
780244-01
Vision Software Included, 2-Port Gigabit PXI Ethernet Interface Module—The PXIe-8234 with Vision Acquisition Software can acquire images from the fastest GigE Vision cameras. It transfers images at full Gigabit Ethernet bandwidth on both ports simultaneously, and it is optimized for extremely low CPU load. The PXIe-8234 with Vision Acquisition Software provides full GigE Vision bandwidth at every port, giving you the bandwidth you need for your most demanding vision applications. It also includes NI Vision Acquisition Software, which is driver software for acquiring, displaying, logging, and monitoring images from a multitude of camera types. With a set of easy-to-use functions and example programs, you can quickly create applications using LabVIEW, C, C++, C#, Visual Basic, and Visual Basic .NET.
-
product
PCI Mezzanine Card
PNIC1G
Each Ethernet interface supports 10, 100 and 1000 Mbits transmission rates with auto-negotiation for full duplex operation; 10 and 100 Mbit/s transmissions for half duplex operation, and is equipped with a 32 Kbit Serial EEPROM.
-
product
PXIe-8238, 10 Gigabit PXI Ethernet Interface Module
784976-01
10 Gigabit PXI Ethernet Interface Module—The PXIe-8238 is a high-performance 10-Gigabit ethernet SFP+ interface for PXI Express based on the Intel 82599 10Gb ethernet controller. It includes two 10-Gigabit ethernet SFP+ ports in a single-slot PXI Express module and is compatible with both copper and fiber optic cabling.
-
product
PXIe-8240, 40 Gigabit PXI Ethernet Interface Module
784977-01
40 Gigabit PXI Ethernet Interface Module—The PXIe-8240 is a high-performance 40-Gigabit Ethernet QSFP+ interface for PXI Express based on the Intel XL710 40Gb Ethernet controller. It includes two 40-Gigabit Ethernet QSFP+ ports in a single-slot PXI Express module and is compatible with both copper and fiber optic cabling.
-
product
PXIe-8245, 4-Port, 10/100/1000BASE-T PXI Ethernet Interface Module
787313-01
The PXIe-8245 supports Ethernet-based communication between PXI hardware and external instruments and devices. This PXI Ethernet Interface Module includes four RJ45 10/100/1000BASE-T Ethernet interface ports in a single-slot PXI Express module.
-
product
PXIe-8280, 1-Port, 50 Gigabit, RDMA PXI Ethernet Interface Module
788261-01
The PXIe-8280 is a high-performance 50-Gigabit remote direct memory access (RDMA) interface for PXI Express. This module includes one 50-Gigabit Ethernet QSFP28 port in a single-slot PXI Express module and supports RDMA over Converged Ethernet (RoCE).
-
product
PXIe-8285, 2-Port, 25 Gigabit, RDMA PXI Ethernet Interface Module
788510-01
The PXIe-8285 is a high-performance 25-Gigabit remote direct memory access (RDMA) interface for PXI Express. This module includes two 25-Gigabit Ethernet SFP28 ports in a single-slot PXI Express module and supports RDMA over Converged Ethernet (RoCE).
-
product
EFT Module for Teststand
The Electronics Functional Test (EFT) Module for TestStand provides out-of-the-box tools to speed up development of automated tests for electronic assemblies including PCBAs, subassemblies and final assemblies. Test engineers can develop, deploy and execute test sequences quickly and efficiently with minimal custom code development for a shorter time-to-solution.
-
product
Test Solutions
Our range of test solutions is far reaching, comprised of off-the-shelf test instruments and interfaces, standard automated test systems, and custom solutions for test, simulation, and training. Put our E2E focus and experience to work for you with these solutions: automated test equipment, maintenance trainers, and test management software.
-
-
product
Tactical Radio Test Set
CTS-6010
The CTS-6010 brings an entire test bench to your front lines. Enable your technicians to detect equipment faults and verify operational capabilities at the I- and O-levels, saving valuable diagnostic time and cost.
-
product
PCIe 5.0 Test Platform
PXP-500A
The Teledyne LeCroy PXP-500A Test Platform provides a convenient means for testing PCIe 5.0 cards with a self-contained portable and powered passive backplane. The PXP-500A provides power required for both cards under test.
-
product
PCI Express 5.0 Test Platform
Teledyne LeCroy’s PCI Express 5.0 Test Platform is part of a suite of tools that facilitates complete protocol testing of PCI Express devices up to and including version 5.0. The latest feature of the Teledyne LeCroy Test Platform is the addition of an integrated interposer, which eliminates the need for an external interposer. This innovation simplifies setup with fewer connection points and outboard devices, making analysis easier and more reliable than ever. In addition to using the Test Platform with the Exerciser, the user can connect two of their own devices and use the Test Platform as a PCIe 5.0 backplane and as an interposer to capture protocol traffic between the systems.
-
product
ARINC 818 Tester
iWave 3U VPX High-Speed Video/Data Processing Card is a rugged standalone module in the 3U VPX form factor, aimed for the high-speed data, video processing, and display applications is ideal for military, defense, and aerospace applications requiring an optimal balance of performance and power efficiency. iWave 3U VPX High-Speed Video/Data Processing Card is implemented using Xilinx Kintex-7 device architecture and has I/O interfaces including High speed 16 channels of transceiver interfaces capable of operating up to 6 Gbps data rate, Gigabit Ethernet, RS232, RS422, PCIe interface, Built-in health monitoring circuits, HDMI input, and output interfaces
-
product
Test System
BMS HIL
The BMS Hardware-in-the-Loop (HIL) Test System is a high performance platform providing all necessary input signals used for battery pack simulation. A real-time operating system executes complex cell and pack models commonly used for BMS algorithm development and firmware regression testing.
-
product
FADEC/EEC Test Platform
The FADEC/EEC Test Platform provides a hardware in-the-loop (HIL) closed-loop test environment for dynamic and maintenance testing of full-authority digital engine control (FADEC) and electronic engine control (EEC) units of both rotary- and fixed-wing airframes. The system simulates one or more turbofan engines, including its sensors and actuators for use with the most sophisticated FADECs and EECs on the market. The system delivers repeatable, cost-effective testing in a fraction of the time needed with typical in-house simulation test systems.
-
product
ESS Performance Test System
The Energy Storage System (ESS) Performance Test System is used to evaluate, test, and certify the performance of energy storage systems up to 2MW. The system is a configurable platform with over 200 channels of simultaneously measured AC and DC voltages and currents, environmental temperatures, airflow, and communications. Intuitive software provides real-time monitoring and analysis of power, energy and efficiency to adhere with industry standards. The test system interfaces hardware such as load banks, and controls the ESS to simulate utility applications such as peak shaving and frequency regulation.
-
product
Flight Control System Test Platform
The Flight Control System Test Platform provides a hardware in-the-loop (HIL) closed-loop test environment for dynamic and maintenance testing of Flight Control Systems (FCS) of both commercial and military aircraft. The system simulates control surface activities from multiple combinations of rudder, flaps, elevator, aileron, and engine controls to the FCS. The system delivers repeatable, cost-effective testing in a fraction of the time needed with typical in-house simulation test systems.
-
product
Functional Test
xUTS
Extend test to encompass copious test points and DUT varieties along with real-time, hardware-in-the-loop and other state-of-the-art instrumentation. extendedUTS (xUTS) is a custom product for high complexity functional test. Configured for the unique needs of a class of devices under test (DUTs), the xUTS employs our universal test system approach that combines the best open platform instrumentation and software along with mass interconnect technology.
-
product
Functional Test
cUTS
Get the essentials of measurement automation to power tests of simpler PCBAs and subassemblies. compactUTS (cUTS) is a cost-effective platform for automating manual tests of devices with fewer than fifty cable-accessible test points in manufacturing environments with moderate production volume. DUT-specific electrically keyed cables make changeover quick and easy.
-
product
Functional Test
UTS
The UTS functional test system is perfect for electronics manufacturing operations that have a mix of products where operators load and unload devices under test (DUT) and routinely change out fixtures for each type of DUT.
-
product
Mixed Signal Battery Test System
The Mixed-Signal Battery-Test System is an automated test platform designed to meet today’s advanced battery test requirements. The platform is ideal for testing a range of battery cells and packs, and can be used in applications such as research and design, quality control, and end-of-line manufacturing. Its distributed architecture provides a scalable solution with configurable system components to accommodate specific applications.
-
product
Functional Test Fixtures
Reliable connections to device under test (DUT) test points are essential for robust functional test. Bloomy provides rugged fixtures and cable sets (ITAs) built for thousands and thousands of cycles in manufacturing environments. With the industry’s best mass interconnects and internal electronic keying, our fixtures are easy to change out and are automatically recognized by the test system.
-
product
Benchtop Automated Functional Test
midUTS
Combining bench-top portability with powerful automated test functionality, the midUTS is an extremely versatile yet cost-effective solution for your electronics functional test needs. Comprised of high-performance commercial-off-the-shelf (COTS) instruments, along with Bloomy’s medium-density signal-routing PCBAs, a built-in or USB-connected PC, and a pair of high-integrity, production-grade cables connected to an adjacent benchtop fixture, the midUTS can be used in engineering for PCBA bring up, as well as scaled to manufacturing to perform high-volume PCBA and sub-assembly functional testing. It is also ideal for depot diagnostic test, debug, and repair of field returns. The two mass-interconnected cables connect the midUTS to as many as 320 test points on the unit under test (UUT), supporting an extreme wide variety of products using bed-of-nails as well as cable-connected UUT test fixtures. Most importantly, the midUTS helps you automate sequences of functional tests using NI TestStand and the Bloomy EFT Module for TestStand. This ideal balance between powerful features and affordable cost allow you to automate earlier in the product development lifecycle, substantially increasing product quality and minimizing time-to-market!
-
product
Electronics Functional Test
Functional test for productive manufacturing. Manufacturers of products enabled by electronics must assure proper operation prior to shipment. Bloomy’s line of universal test systems are ideal for functional test of your PCBAs and subassemblies, from the simplest to the most complex. The UTS family of products combines high-performance test instruments, switching, power control and mass-interconnect hardware with our robust UTS software suite into a low-risk, cost-effective and powerful test solution for your device under test (DUT).
