Filter Results By:
Products
Applications
Manufacturers
-
product
Online Dissolved Oxygen Controller
LD-LODC-A10
Online Dissolved Oxygen ControllerLD-LODC-A10features 1 to 2 points dissolved oxygen calibration system, and 4 to 20 mA output signal transmitter. The large and clear back light LCD displays Calibration and setup values, temperature values, ATC (automatic temperature compensation) values, high and low limit of measurement. It measures the amount of dissolved oxygen in mg/l, ppm units or in % of saturation. The accuracy of measurement is improved by manual salinity and barometric pressure compensation mode.
-
product
Leak And Seal Strength Detector
LSD-02
Jinan Leading Instruments Co., Ltd.
LSD-02 Leakand Seal Strength Detector is applicable in the quantitative measurement of leak, heat seal strength, heat seal quality, and burst pressure of each heat sealedges of the flexible packages that are made using heat seal and adhesiveprocessing, as well as sterilized packages; the quantitative measurement ofleak performances of all kinds of plastic pilfer-proof closures; thequantitative measurement of the unitary airproof, compression resistancestrength, cap body joint strength, cap disengaging strength, seal strength ofedge and butting strength of various flexible tubes. It can also provideevaluation and analysis for the compression and burst resistance strength ofthe materials of flexible packaging bags, the torsional airproof index of cap,the cap joint and disengaging strength and the stress strength; as well as theairproof performances, the compression resistance performance and the burstresistance character of unitary bottle, etc.
-
product
Vector Network Analyzer
R42XXE
The R42XXE Vector Network Analyzers are designed for measuring of S-parameters, VSWR and impedance of waveguide networks in the full frequency ranges of standard waveguides between 33 and 170 GHz. Frequency accuracy is ±0.2%. The measurement range of reflection factor modulus is from 0 to 1. The measurement range of reflection factor phase is from 0 to ±180° for 0.1< |Гx|<1 with accuracy ±7.5 o in 18-75 GHz frequency range and ±9.6° in 75-170 GHz frequency range. The measurement range of transmission factor phase is from 0 to ±180 o with accuracy ±(5+0.1 |Ax|) o for Ax >-50 dB in frequency range to 75 GHz, for Ax >-30 dB - to 170 GHz. Data can be displayed in the rectangular, Smith or polar diagrams. VNA requires Personal Computer with USB interface.
-
product
WATOM
Wafer edge and notch profile measurementThe use of smaller and smaller patterns in the semiconductor industry calls for increasingly advanced materials of extremely high quality. In response to the steady improvements in the quality of wafers, KoCoS Automation has developed WATOM, a wafer edge and notch profile measurement tool which heralds a new era of extremely precise wafer geometry measurement.WATOM supports quality assurance throughout the wafer manufacturing process, starting at the very beginning and continuing on through to wafer reclaim.The WATOM Edge and Notch Wafer Geometry Analyser sets the worldwide benchmark for the quality assurance of geometrical measurements in semiconductor wafer manufacturing, combining the highest quality standards with top-class service. These high-precision, laser-based edge profile measurement tools are specially designed for optimum integration in manufacturing lines within the semiconductor industry.
-
product
Active Loop Antenna
AL-130R
Also known as Magnetic Loop Antenna, the AL-130R is compliant with CISPR 16-1-4. It is ideal for emissions measurements as required by various EMC standards such as FCC 18, CISPR 11, CISPR 13, CISPR 14, CISPR 32 and many more. The built-in, low-noise preamplifier, increases overall measurement sensitivity as well as the overall signal to noise ratio. As per ANSI C63.4-2014, the use of active loop antenna for compliance testing is permitted in a non-sheilded environment ONLY if the saturation indicator is continuously monitored during the course of testing. Com-Power’s Remote Antenna Interface (RAI-100) comes in very handy for this application. It is a compact controller which can be used to enable/ disable RF measurement circuit and monitor saturation and battery low conditions remotely via a fiber optic cable up to 30 mtrs in length.
-
product
Optical Coordinate Measuring System
MaxSHOT 3D
Creaform’s MaxSHOT 3D lineup is a game changer for product development, manufacturing, quality control and inspection teams that need the highest measurement accuracy and repeatability as much for large‑scale projects than parts from 2 to 10 m. Imagine achieving accuracy better than 0.015mm/m! Thanks to its sophisticated user guidance technology and easy‑to‑use software, the MaxSHOT 3D is ideal for users of all levels—even non‑metrology experts—so that you gain peace of mind knowing your measurements are always right on the dot and you increase process efficiency. If you consistently work on large‑scale projects, the MaxSHOT 3D is your go-to solution to slash budget-busting measurement mistakes, improve product quality, increase process efficiency—and minimize overall operating costs.
-
product
Ultrasonic Bolt Meter - Bolting System
Mini-MAX-Series
The MINI-MAX, Ultrasonic Bolt Tension Monitor, defines the state of the art in the measurement of the actual elongation produced by tightening a threaded fastener. The MINI-MAX can measure the elongation very accurately in fasteners of virtually any material from 1/2 inch to 4 feet in length. The measurement is achieved by determining the change in the transit time, of an ultrasonic shock wave along the length of the fastener as the fastener is tightened by any method. The on-board microcomputer automatically interprets this time measurement to display the time(nanoseconds), elongation, load, stress, or %strain from stretching a fastener. Through the use of high speed digital signal processing and automated diagnostics, the MINI-MAX minimizes the requirement for extensive operator training. With built in data recordation and reporting through an RS232 interface, the MNI-MAX offers an easy to use and reliable solution to the most difficult bolting problem.
-
product
cDAQ-9184, 4‑Slot, Ethernet CompactDAQ Chassis
782069-01
4‑Slot, Ethernet CompactDAQ Chassis - The cDAQ‑9184 is a CompactDAQ Ethernet chassis designed for small, remote, or distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use a combination of modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The chassis also has four 32‑bit general‑purpose counters/timers built in. You can access these counters through an installed, hardware‑timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement. With multiple timing engines, you can run seven hardware‑timed operations simultaneously, with three independent rates for analog input.
-
product
cDAQ-9191, 1‑Slot, Ethernet and 802.11 Wi‑Fi CompactDAQ Chassis
781497-01
1‑Slot, Ethernet and 802.11 Wi‑Fi CompactDAQ Chassis - The cDAQ‑9191 is a Wi‑Fi chassis designed for small, remote, or distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this chassis with a combination of modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. You can send data from the cDAQ‑9191 to a host PC over Ethernet or IEEE 802.11 Wi‑Fi. The chassis also has four 32‑bit general‑purpose counters/timers built in. You can access these counters through an installed, hardware‑timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement.
-
product
C Series Counter Input Module
The C Series Counter Input Module features flexible, 32-bit counters. You can configure each channel to read a single pulse train or combine them to read up to four incremental encoders. You can also directly connect sensors with open-collector or push-pull outputs by using an internal, switchable pull-up resistor. Additionally, you can use the C Series Counter Input Module to perform encoder position and velocity measurements as well as to synchronize the counters with other analog, digital, and counter measurements in your chassis.The C Series Counter Input Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
product
Light Meters
A light meter is a very sensitive electronic measuring device used to help monitor the illumination of any given area. Most light meter devices are small in size, simple to operate and equipped with an easy-to-read lighted screen made of special glass. Typically, a heavy-duty housing protects the light sensor inside the light meter from damage. A light meter is used for measuring brightness in lux (lx), foot candle (fc) or candela per square meter (cd/m²)measuring units. Some light meter devices are equipped with an internal memory or data logger to record and save measurements. The measurement of light intensity with a light meter is becoming increasingly important in the workplace due to safety concerns. Light measurement is also necessary to determine the best location and angle when installing and adjusting solar panels.
-
product
Circuit Breakers for Equipment
Mitsubishi Electric Automation, Inc
The optimum circuit breaker for opening/closing power sources and preventing overload and short-circuit conditions in control circuits of automation applications, construction equipment, office machines, communications and measurement devices.
-
product
Circulators
Atlantic Microwave's coaxial circulators are designed for low power applications in communications, test and measurement and scientific research applications requiring excellent RF performance in a compact and economic package.
-
product
Clamp Meters
AC/DC Clamp True RMS 600/2000 A range V, A, Hz, , and other extensive measurement parameters Inrush current Max/Min/Avg/Peak Wireless data download to a tablet or smartphone
-
product
DC Stable Electrostatic Voltmeter
Model 370
The Trek Model 370 is a precision electrostatic voltmeter with the unique capability of making noncontacting surface voltage measurements in the range of 0 to ±3 kV DC or peak AC.
-
product
Diesel Engine Monitoring
Cylmate System
ABB's Cylmate System is a comprehensive system for continuous engine performance measurement and monitoring. With the Cylmate System you will get the key knowledge for obtaining optimum and reliable engine performance.
-
product
eVe LIDAR
eVe LIDAR aims to provide the ESA-Aeolus mission with a flexible, mobile reference ground-based LIDAR system capable of providing well-characterized fiducial reference measurements of aerosol optical properties
-
product
Fault Detection Device in PV String
Hanwa Electronic Ind. Co.,Ltd.
◆Very light and easy to carry.◆Possible to find fault areas that can’t find by Voc.◆Measurement Voc and Vc.◆Possible to check data and record the data using Android.
-
product
Fixed Spot Non-Contact Thermometers / Pyrometers
SPOT is a family of fully featured, high performance pyrometers for fixed non-contact infrared spot temperature measurements. Available in range of operating wavelengths, temperature ranges and process requirements.
-
product
Gas Gravimetric Sorption Analyzer
XEMIS Series
The XEMIS series offers reproducible, high resolution, high accuracy measurements even with small sample sizes or small uptakes, and performance unrivalled in a high pressure sorption analyzer.
-
product
Gauge Blocks
Practical master gage for dimensional measurement Two types of steel and ceramic gauge blocks are available. Four classes of Class K‚ Class 0‚ Class1‚ and Class 2
-
product
High Current SMU Family 2000 A
AXC76xx
Generate very short, fully regulated current pulses from 2 ms to DC with up to 2000 A. Carry out measurements directly on the DUT with the integrated CMU and VMU.
-
product
High-Sensitivity, DC Stable ESVM
Model 320C
The Trek Model 320C Electrostatic Voltmeter is a versatile instrument which is used for a variety of electrostatic applications including contact potential measurements, materials evaluation, and electret studies.
-
product
INnLline Metrology Automated & Robotized Solutions
Automation projects
Bring automation to an existing manual inspection process. Integrate 3D measurements on the shop floor for better traceability. Increase part inspection throughput and reduce cycle times and costs.
-
product
Ion/pH/mV Meter with Single Junction pH Electrode
Ion 6+
Direct Ion Concentration for use with most mono- or di-valent Ion Selective Electrodes (ISE) :: mV measurement mode allows you to check performance and calibration of your ISE
-
product
KF Moisture Titrator
Hybrid titration methodEasy factor determination by “Electrolytic Factor Measurement System”Unique integrated “Hybrid titration cell” of both “Volumetric titration method” & “Coulometric titration method”
-
product
Liquid Nitrogen Data Logging System
LNDS
MadgeTechs LNDS, Liquid Nitrogen Data Logging System, is an ultra-low temperature measurement system created specifically for the monitoring of temperature sensitive substances that need to be preserved at cryogenic temperatures.
-
product
Ohmmeter
PDRM-1A
The PDRM-1A ohmmeter is very accurate for measuring low resistances. You can measure values from 1µΩ to 200Ω. For this reason, it allows a wide variety of measurements to be made with a single instrument.
-
product
Platinum and Nickel RTD Temperature Sensors
Accurate, repeatable and robust resistance temperature detector (resistance thermometers) sensor assemblies manufactured provide fast temperature response and can be applied in most temperature measurement and control applications.
-
product
Power Analyzers
Current measurement option for PW6001/ 3390/ 3390-10 Wide-band DC to 3.5MHz, 50A AC/DC rated input, 0.04V/A output PW9100-03 : 3 channels PW9100-04 : 4 channels