Showing results: 4006 - 4020 of 10566 items found.
-
USB-CTR-15 -
Acces I/O Products, Inc.
The USB-CTR-15 is an ideal solution for adding portable, easy-to-install, counter/timer capabilities to any PC or embedded system with a USB port. This board is packaged in a small, rugged, industrial enclosure and features 15 independent 16-bit counter/timers. The unit is a true USB 2.0 device, offering the highest speed available with the USB bus. It is fully compatible with both USB 1.1 and USB 2.0 ports. The unit is plug-and-play allowing quick connect/disconnect whenever you need additional counter/timer devices on your USB port. The USB-CTR-15 can be used for a wide variety of measurement applications including event counting, frequency measurements, position measurement, pulse counting, pulse-width modulation and pulse generation. The OEM version provides just the board without the enclosure or external screw terminal board and is ideal for a variety of embedded OEM applications.
-
PCE Instruments
There are both standard and a waterproof conductivity meter, as well as a conductivity meter available for flowing water or pure water (highly recommended for specific industries) as well as the ones with different conductivity measurement ranges. An important factor is that a conductivity meter normally measures electric conductivity in µS/cm, however it can also take measurements in mg/l (for direct reading of content in dissolved solid substances). The relation is established as follows: 2 µS/cm = 1ppm (parts per million) = 1 mg/l. Compensated temperature in the conductivity meter can be automatic or by hand.
-
NI
The C Series Voltage and Current Input Module features up to 16 input channels with built-in noise rejection. You can use this module to combine the two most common inputs to reduce the overall number of modules you need in your measurement system.The C Series Voltage and Current Input Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
LD-LGMM-A10 -
Labodam
Digital Grain moisture MeterLD-LGMM-A10is an advanced digital moisture measuring device with automatic moisture measurement of wide variety agriculture grains. It has most advanced revising mode and user friendly material type selection mode. Automatic temperature adjustment and moisture correction when no material is measured are important feature of this device. It works on AA batteries and consists of automatic power shut down feature. It is ideally used for moisture measurement in agricultural grains like wheat, soybean, beans sediment, coffee beans, rice, etc.
-
LD-LHMM-A10 -
Labodam
Digital hay moisture meterLD-LHMM-A10is a digital device used for determination of moisture content in the various types of hay samples from agricultural waste. High frequency principle of more than 10 MHz is used for moisture measurement. It gives high precision test results due to wide measuring range. Quick moisture determination is achieved due to its compact and light weight design. Ideally used for moisture measurement in samples like sugarcane waste, corn stalks, wheat straw, bamboo, tobacco leaf, etc.
-
Huaxin instrument (Beijing) Co., Ltd
Reputed as a specialized pressure measurement solution provider, Huaxin offers an excellent selection of digital pressure gauges. Unique industrial design and state of the art technology have made our digital pressure gauges an ideal pressure calibration instrument for various applications. Depending on high and low temperature aging and temperature compensation processes before delivery, they feature guaranteed accuracy and stability. The digital gauges have been extensively used in power, metallurgy, chemical, measuring and military industries for calibrating precision pressure measurement devices.
-
SDS1000CML+ Series -
SIGLENT Technologies
SDS1000CML+ series is a dual-channel universal digital oscilloscope, available in 70, 100, and 150 MHz bandwidth models. It includes a 2 Mpts memory depth that helps to ensure accurate waveform resolution and to capture longer signal lengths. With its 7-inch TFT-LCD (800*480) screen, there is adequate screen space to help better see and analyze waveform details. Along with a 1 GSa/s sampling rate, the SDS1000CML+ supports 32 parameters measurements and common mathematical operations to speed up complex / repetitive measurements.
-
Omni-λxxxD -
ZOLIX
Omni-λxxxD series Double Monochromators/SpectrographsThe Double Monochromators/Spectrographs include two 300 mm focus monochromators( or 500 mm, 750 mm focus) which are with fine alignment. Double Monochromator has the dispersion subtraction mode and dispersion sum mode. Using dispersion sum mode, the double monochromator / spectrograph spectral resolution can be doubled, suitable for high resolution measurement. Using dispersion subtraction mode, the double monochromator / spectrograph stray light can be reduced effectively, suitable for weaker signal detection, such as Raman spectral measurement.
-
72-2995 -
Tenma
40,000 count industrial True RMS digital multimeter is a highly versatile handheld instrument boasts 5-1/2 digit TRMS accuracy. It provides AC/DC voltage and current measurement, resistance, capacitance, temperature and frequency measurement, displaying readings on a backlit LCD digit and analogue bargraph display. Other features include non-contact voltage detection, continuity and diode test and USB data logging. All this is housed in a rugged overmolded enclosure with carry case, test leads and USB interface cable included.
-
FLIR DM285 -
Teledyne FLIR
The FLIR DM285 is a professional, all-in-one True RMS digital multimeter and thermal imager. Featuring Infrared Guided Measurement (IGM) technology powered by a built-in 160 x 120 FLIR thermal imager, the DM285 visually guides you to the precise location of an electrical problem without direct contact. You’ll pinpoint hot spots faster, safer, and more efficiently. The DM285 also helps streamline inspections by connecting wirelessly to FLIR Tools® app for uploading thermal images and measurement data.
-
ThermoWorks
Easily measure surface temperatures with ThermoWorks non-contact IR guns, ideal for produce and agriculture inspectors, HVAC, construction, warehouse, quality assurance, HACCP and cold chain management, both shipping and receiving. Choose from fixed or adjustable emissivity; single, dual or circle laser types; and lens optics from close focus—for electronic components and laboratory measurements—to 100:1—for long distance measurements. High temperature ranges up to 3272°F (1800°C) are perfect for metallurgy and metal work foundries.
-
PU 187.21 -
Metra Blansko a.s.
Instrument PU 187.21 MEGMET 1000 D is intended for measurements of the insulation resistance up to 20 GΩ and the resistance of protective conductor up to 2 kΩ, its length; it can be used for checking the over-voltage protections. It also measures DC / AC voltage up to 1000 V and the temperature within the range -20 °C ÷ 120 °C, with a connected external sensor within the range -50 ÷ 850 °C. Nominal measuring voltages for the insulation resistance measurements are 50, 100, 250, 500, and 1000 V.
-
TF series C13555MA -
Hamamatsu Photonics K.K.
he mini- spectrometer TF series is a polychromator provided in a compact, thin case that houses optical elements, image sensor, and driver circuit. Spectrum data can be acquired by guiding measurement light into a mini-spectrometer through an optical fiber and transferring the measured results to a PC via the USB connection. The incorporation of a high-sensitivity CMOS image sensor maintains high sensitivity equivalent to that of a CCD and achieves low power consumption. Moreover, the trigger function that can be also used for short-term integration enables spectroscopic measurement of pulse emissions.
-
Com-Power Corporation
A typical emi emission test is performed using broadband EMC antennas such as biconical, log periodics, Combilogs and horns. These antennas usually placed at 1, 3 or 10 meter distance as required by the test specification. These is considered far field measurements and the emission limits are given for the specific distance by the specification. During EMI compliance measurements, the emissions levels from products are compared with these limits. If the product exceeds these limits it is considered failing. These tests are typically conducted in a open area test site IOATS) or inside an anechoic chamber.
-
BAS001 -
Larson Davis, Inc.
The BAS001 Source is designed to generate omnidirectional sound fields for making standard compliant measurements including: reverberation time (ISO 3382, ASTM E2235), building acoustics (insertion loss, acoustic absorption area, etc: ISO 140-4 ISO 140-3, ASTM E336, ASTM E90, DIN 55 210). The BAS001 is typically used to saturate a room with a uniform acoustic field. The available high-efficiency power amplifier has no fan for cooling, allowing measurements in quiet environments, like those in reverberation time applications.
