Filter Results By:
Products
Applications
Manufacturers
-
product
Concrete Moisture Test Meter
Rapid RH 4.0 EX
The Rapid RH 4.0 EX concrete test is superior to all other humidity measurement systems on the market today. Rapid RH 4.0 EX concrete moisture tests equilibrate faster than other concrete moisture tests. The reading taken one hour after installation for concrete relative humidity content will be within 3% of the final reading.
-
product
Concrete Surface Resistivity
Surf
Giatec Surf™ is a laboratory test device for rapid, easy and accurate measurement of the surface electrical resistivity of concrete based on the four-probe (Wenner-Array) technique. The Surf™ patented technology automatically measures resistivity around the concrete specimen using four channels of 4-probe array (located at 90° from each other). The PC software generates the required reports according to the standard specifications.
-
product
Conductivity Electrode
As current-carrying and potential difference measuring electrodes, platinum was deposited on a quartz glass substrate. Voltage terminal distance can be varied by changing the connection pin. In-situ measurement of the metal transition produced in a conductive polymer insulator doping, 4 terminal electrode is used, where for insulator layer with low doping side 2 terminal method and for metal layer with high doping side 4 terminal method is used for the measurement. With this electrode, become possible to have measurement in 15 distances by combining the connection terminal.
-
product
Conductivity Meter
PLN-Sigma 2008
Hangzhou Pulani Electronic Co.,Ltd
Two kinds of measuring units (MS/m or %IACS) for convenient select. Easy to switch to resistivity value on the measurement face
-
product
Conductivity Meters
There are both standard and a waterproof conductivity meter, as well as a conductivity meter available for flowing water or pure water (highly recommended for specific industries) as well as the ones with different conductivity measurement ranges. An important factor is that a conductivity meter normally measures electric conductivity in µS/cm, however it can also take measurements in mg/l (for direct reading of content in dissolved solid substances). The relation is established as follows: 2 µS/cm = 1ppm (parts per million) = 1 mg/l. Compensated temperature in the conductivity meter can be automatic or by hand.
-
product
Conductivity Sensors
Conductivity sensors measure the specific conductance of liquid processes. The specific conductance is directly related to the presence of ionic species and their concentration. Barben Analytical offers a full range of two electrode and four electrode contacting conductivity sensors for a variety of industrial measurement applications.
-
product
Conductivity Switches
B/W Controls offers a simple conductivity holder and electrode that can be configured for multiple measurement points. This is a simple level switch that can be used on liquids and light slurries. The B/W products utilize the conductive properties common to aqueous liquids to provide point level control and alarm functionality.
-
product
Conductivity Tester
EC
Monitor conductivity levels quickly and easily with Series EC Conductivity Testers. These pocket-sized testers are ideal for conductivity measurement in the lab, industrial plant or out in the field. Series EC measures conductivity from 0 to 1990 microhms (S) or 0 to 19.90 milliohms (mS).
-
product
Connect PT100/PT1000 Sensors To Output A Voltage Signal
K- PT100/1000
Our K-PT module is designed to connect up to PT100/PT1000 sensors and simply provides an output voltage signal. Thus enabling the most standard voltage measurement devices to work with PT100/PT1000 sensors. The PT100 sensors offer excellent accuracy and repeatability.
-
product
Contact and Non-Contact Tachometer
Amprobe TACH-20
The Amprobe TACH20 Hand-held Tachometer accurately measures rotational or surface speed as well as length. It comes with a large LCD display that allows the user to easily read the measurement. It also has a built in memory function that permits automatic storage of maximum, minimum, average values plus the last measurement displayed.
-
product
Contacting Extensometers
AMETEK Sensors, Test & Calibration
The contacting extensometers are designed for accurate strain and extension measurement of a material up to a maximum sample thickness of 25 mm.
-
product
Contacting Extensometers
The contacting extensometers are designed for accurate strain and extension measurement of a material up to a maximum sample thickness of 25 mm.
-
product
Contact Resistance Meter
PCRM200S
The Motwane Manufacturing Company
The Motwane make Contact Resistance Meter (Model:PCRM200S) is a digital micro-ohmmeter, specially designed to measure extremely low resistance in micro ohm. The Instrument is based on Kelvin 4-wire connection method for measurement of low resistance.The Current injection is fixed at 100A & 200A. Test information like current injected with measured resistance & voltage drop is displayed with real time data on large LCD with backlit.This User friendly Instrument and it's accessories are housed in easy transportation case. Advanced Windows based software isprovided for data downloading, analysis and report generation. Internal memory of 199 records is provided for onsite data storage withDate & Time stamping & Recalling facility. Thermal printer is the additional feature provided to print the test results.
-
product
Continuous Internet Speed Test Tool
*Internet speed stress test with long duration: long-term download and upload bandwidth (speed) test tool*Cross-platform: HTML (online), Windows, Linux, Android versions, free for non-commercial use (please contact us to get a commercial license)*Measures download and upload bandwidth, packet loss and round trip time (RTT, ping)*Measures and tracks bandwidth of your internet connection during a long (unlimited) period of time*Measures stability of internet connection (uptime in percents, bandwidth measurements)*Tracks connection outages and drops of bandwidth*Runs on your own Windows PC as a server, to check stability of your LAN/wifi router(s)
-
product
Continuous Level Measurement
Drexelbrook manufactures a full range of continuous level measurement instruments, providing the highest level of performance for liquids, slurries and bulk solids applications. With a wide variety of technology options, Drexelbrook is uniquely qualified to properly evaluate and recommend the very best solution for your application.
-
product
Continuous Magnetic Measurement Equipment
CWM
The automatic measurement equipment to continuously measure magnetic property in commercial power frequency of magnetic steel sheet sample on line, is used for quality control. Core loss in definite time of magnetic flux density [B] or magnetic flux density [B] in definite time of strength of magnetic field [H] for excited magnetic steel sheet is measured on line.
-
product
Continuous Measurement With Float
WIKA Alexander Wiegand SE & Co. KG
Our level sensors enable the continuous detection of levels, independent of physical and chemical changes of the media such as foaming, conductivity, dielectric, pressure, vacuum, temperature, vapours, condensation, bubble formation, boiling effects and density change. Via the HART® interface, parallel measurement of interface layer and overall level is possible. The level can be displayed proportional to height or volume. Process connection, guide tube and float can be manufactured from stainless steel 1.4571, 1.4435, 1.4539, titanium or various plastics.
-
product
Continuous Particulate Monitor
BPM-200
The BPM-200 measures ambient particulate by using well-applied beta ray attenuation technology. PM2.5 measurement can also be achieved by introducing the corresponding cyclone.
-
product
Contour Measuring Machines
arious kinds of measurement is achieved by upper / lower surface continuous measurement and measurment adjustable functionEquipped with new arm fixed by a magnet-type attach/detach mechanism
-
product
Controllers
Designed for the continuous measurement of pH, ORP, pION, Dissolved Oxygen, Turbidity, Conductivity or Resistivity in a general purpose industrial environment.
-
product
Controllers
CCS
Sciences et Techniques Industrielles de la Lumière
CCS controllers allow high precision measurements without contact and without risk of damaging the parts.Among the various advantages of CCS controllers is the measurement of distance and thickness at very high resolution on all types of surfaces and materials, including reflective surfaces.
-
product
Control Unit
Epec 3610
Epec 3610 Control Unit is a compact controller containing 22 I/O pins, all of them can be configured as input pins. Epec 3610 has an RS-232 serial port and as an assembly variant, I/O interface that is compatible with the previous Epec 2038 Control Unit. However, Epec 3610 also comes with completely new features like high-side current measurement and an internal 3-axis accelerometer, for example, for levelling purposes. Epec 3610 also has an option for accurate Pt1000 measurement.
-
product
Convergence Gauge
This small, handheld, opto-mechanical device is used to measure the convergence error between the lines of a CRT display. This sturdy, accurate tool is sufficient to obtain measurements that are invaluable to engineers, manufacturers, and quality inspectors. The CM7A series is made for monitors, the CM14A series is for medium-sized screens, and the CM28A series is for large-screen and rear-projection big-screen TVs.
-
product
Coordinate Measuring Machines
FlatScope
Perfect for the measurement of larger 2D profiles (e.g.),films, circuit boards, laser cut and stamped parts large and smallMachine design with the image processing sensor under the glass plate, eliminates time-consuming focusing as the workpiece is always in the correct distance to the opticsIn raster scanning mode the machine also quickly captures the selected measurement range completelyAll geometric features are then evaluated automatically in the imageQuick dimensional measurements in the scanned image and automatic gaging with ToleranceFit® comparisons
-
product
Coordinate Measuring Machines
The LK Metrology range of Coordinate Measuring Machines represent the ultimate in CMM technology. Designed and manufactured using only the highest quality materials, they carry a heritage of over 55 years experience and expertise. LK CMMs deliver the ability to perform dimensional, positional and surface measurement in a single system.
-
product
Coordinate Measuring Machines
Novacam's 3D Non-Contact Coordinate Measuring Machines are designed with versatility and superior performance in mind: Precision (better than 1um) Speed (1-30 thousand measurements per second) Simultaneous dimensional and surface inspection Smallest probes measuring 0.9mm in diameter Automation by teaching with joystick Portability
-
product
Coordinate Measuring Machines
CMM
Aberlink offers a wide range of bridge and hexapod CMMs to suit all applications and budgets, enabling the precise measurement of the smallest of components to parts of over 3 metres long and up to 6 tonnes in weight with a wide range of touch-trigger probes and non-contact measurement options. The comprehensive range of CMMs includes 32 standard sizes of both CNC and manual variants. All CMMs are supplied as a complete turnkey package including the Aberlink 3D measurement software, the easiest to use and most intuitive CMM software currently available.
-
product
Coordinate Measuring Machines
ScopeCheck® FB
High performance multisensor CMM for larger workpieces in the measurement lab or production environmentFixed bridge design allows for larger measurement rangesHeavy duty granite base guarantees low measurement uncertainty even with multiple sensorsLarger measuring ranges are availableContour image processing for fully automatic measurements of simple and complex geometrical elementsTemperature compensation included for accurate measurement on the shop floor
-
product
Coriolis Mass Flowmeters
CMF
Applicable Fluids: Gases Slurries Liquids. Typical Applications: Custody transfer Reactor feed ratio Density measurement Batch control.
-
product
CO₂ Sensor
STC31 (Qwiic)
Do you need to be able to sense CO2 concentrations of up to 100%? If so, the STC31 is the sensor for you! The Sensirion STC31 thermal conductivity sensor has two CO2 measurement ranges: 0 to 25 vol%; and 0 to 100 vol%. The measurement repeatability is 0.2 vol%, with a stability of 0.025 vol% / °C. The measurement accuracy depends on the measurement range: 0.5 vol% + 3% measured value; 1 vol% + 3% measured value.