Showing results: 4501 - 4515 of 7317 items found.
-
JFW Industries
In circuits are used to lower voltage, dissipate power, and to improve impedance matching. In measuring signals, attenuator pads or adapters are used to lower the amplitude of the signal a known amount to enable measurements, or to protect the measuring device from signal levels that might damage it.
-
DAQ -
ADLINK Technology Inc.
From entry-level to high-end, data acquisition to digital input/output, ADLINK provides a diversity of modular instruments with market-leading price/performance ratio, for bigger and better measurement and automation systems. Now high-speed digitizer, switching, simultaneous data acquisition, high-density multi-function data acquisition, analog output, digital multimeter, and arbitrary waveform generator categories are all available.
-
Supracon AG
In the measurement setup of SQUID electronics (detector variant), the dc SQUID amplifies the small amplitude signals of the detector with a large bandwidth so that they can be further processed with conventional AD converters.
-
UVP-365 -
SAN-EI ELECTRIC CO.,LTD.
This is the standard measurement instrument to measure absolute UV vaiue. All SAN-EI's UV light source fixtures are measured by this meter.
-
UVM-MP -
SAN-EI ELECTRIC CO.,LTD.
Measurement of maximum of 6 points is possible. By use of thee sensor amplifier box, distance between the light receiving inlet and the controller can be extended to 10 meters. Measurement start signals can be independently output by remote control. This is useful for the light source fixtures integrating shutter mechanism.
-
-
TAC1000 -
Rhesca Co., Ltd.
For the measurement of tackiness (instantaneous adhesive strength) of various pastes and adhesive tapes, it is possible to quantitatively evaluate the data, which until now had large errors due to individual differences. First, press the measuring probe, which is controlled (approach speed, pressure force, pressure time, separation speed) against the sample, and measure the adhesive force in the process of separating. Measured data can be processed by a computer. With double temperature control (patented), the sample piece is preheated from the back side with a hot plate and the heated probe penetrates the measurement surface, making it possible to keep the set temperature and the temperature of the test surface to be evaluated constant. Since the pressurization time can be as short as 10msec, it is possible to measure the tackiness caused by momentary contact.
-
PTR1102 -
Rhesca Co., Ltd.
In wire bonding in semiconductor manufacturing, electrodes are joined using gold wires of several tens of microns. In order to measure the pull (tensile) strength and ball shear (shear) strength of this gold wire, this machine has load detection accuracy and fine positioning accuracy. In addition, for the measurement of high load areas such as die shear strength and solder joint strength, this machine supports measurement in high load areas while maintaining accuracy in low load areas by replacing the sensor part.
-
FPR2200 -
Rhesca Co., Ltd.
The friction coefficient is measured by the pin-on-disk method. Also, by measuring the coefficient of dynamic friction, surface destruction occurs due to wear and changes in the coefficient of dynamic friction occur .This machine is the latest model that was created by realizing various measurement modes, improving data resolution, and pursuing ease of use based on the achievements cultivated in the friction and wear tester that we have manufactured and sold in the past.
-
CSR1000 -
Rhesca Co., Ltd.
This tester is highly effective in measuring the adhesion strength (adhesion strength) of hard coatings (Ti, TiN, SiC, DLC, etc.) formed by PVD and CVD on metal surfaces such as cemented carbide. Adopting a scratch test method that allows quantitative measurement with simple operations, the film surface is scratched while increasing the load on the sample surface, detecting film breakage with high sensitivity, and providing the load at which film breakage occurs (critical load). tools and mold tools that require
-
Model 1000 -
Teledyne Gas & Flame Detection
Natural gas pipeline monitor to detect H2S and CO2.Detcon Model 1000-CO2 and Model 1000-H2S Analyzers are designed to provide continuous, accurate, real-time measurement of gas concentrations in a wide variety of process gas streams. The instrument package is rated for Non-Hazardous areas.Consult commercial brochures for measurement ranges and more product features.​​
-
Gascoseeker 2-500 -
Teledyne Gas & Flame Detection
Built on the success of the robust and reliable Gascosee​​​​​ker MK2, the Gascose​eker ​​2-500 is the U​K gas industry standard instrument for measuring % LEL and % volume flammable hydrocarbons, with over 20,000 instruments in use in the UK gas industry.​The two-button operation means the Gascoseeker 2-500 is easy to use and operator training can be conducted quickly. The rugged design allows the Gascoseeker 2-500 to be used in harsh environments. The Gascoseeker 2-500 is also fully compatible with our range of calibration software and equipment.​​​​
-
Teledyne Gas & Flame Detection
Looking for portable gas leak detectors to protect your staff? Teledyne Gas and Flame Detection measuring devices meet all your requirements.
-
-