Filter Results By:
Products
Applications
Manufacturers
-
product
Gel Strength Test System
LD-LGST-A10
Gel Strength Test SystemLD-LGST-A10is mainly used to measure the gel strength of gelatine under the stipulated environment. It has traveling accuracy ± 0.3 % and Test range up to 5 to 1000 g Bloom. It consists of Jelly Strength Tester, Constant Temperature Bath and Refrigerator. Sampling depth can be present arbitrarily in 1 to 60 mm. It consists four kinds of sampling measurement modes: single-step, maintaining, circulating and automatic.
-
product
Edge Gateway
The Edge Gateway provides a solution to manage distributed wireless sensors. On the one hand, new sensors can be added to the measurement systems easily and on the other hand, the gateway is powerful enough to evaluate the measurements and detect irregularities.
-
product
F9 Systems CalBlade
The CalBlade backplane calibration fixture isdesigned to permit accurate and convenient impedance and transmission measurements of a HM-Zd backplane. The CalBlade is used to calibratethe logic card connector interface to the backplane rather than to the usual far-end of the coaxial measurement cables. Very accurate impedance, skew and propagation delay measurements are possible since parasitic fixturing effects are removed.
-
product
Electrochemical Analyzer/Workstation
600E
The Model 600D series is designed for general purpose electrochemical measurements. The figure below shows the block diagram of the instrument. The system contains a fast digital function generator, high speed data acquisition circuitry, potentiostat, and a galvanostat (available only in select models).
-
product
Hall Effect Measurement system
HMS-3300
Magnetic flux density : 0.55Tesla (+/-0.03T)Gap distance between both round magnets : 26mm / Round magnet diameter : 50mmMeasurable temp : RT ~ 300℃(model# HT55T3). Resolution : 0.1℃(Model# HT55T5 : RT ~ 500℃)Both HT55T3 and HT55T5 are only capable of using with HMS-3000 main body.(Not compatible with HMS-5000 )- You can flow purge gas into small chamber and measure hall effect at the same time. Gas control valve can be installed as an option.
-
product
EBSD Detector
e–FlashFS
The new EBSD detector e–FlashFS has been designed for maximum sensitivity to allow highspeed EBSD measurements without compromising data quality – even on challenging applications like deformed or lightweight materials. To further improve the pattern quality, the cooling system of the e–FlashFS has been upgraded to lower its functioning temperature and therefore reduce the dark current of the CCD camera as much as possible.
-
product
Dynatrol® Density Cells
CL-10HY
The Dynatrol® CL-10HY Density Systems achieve exceptional accuracy over a wide range of process changes in ambient temperature, pressure, viscosity or flow. Our systems are designed for density measurement in familiar units like specific gravity, API gravity, Baumé, BRIX°, as well as being able to measure the percent solids or percent concentration of a liquid or slurry.
-
product
Ellipsometer
T-Solar™
The T-Solar ellipsometer combines the best photovoltaic measurement technology into a single system designed specifically for textured samples. Based on the establishedM-2000 rotating compensator spectroscopic ellipsometer, the T-Solar measures hundreds of wavelength across the UV-Visible-NIR.
-
product
Hall Effect Measurement system
HMS-5300
Variable temp : 80K ~ 350K (model#: AMP55T ) - HMS-5300 can be compatibly used with both low temp magnet kit (model# : AMP55T) and high temp magnet kit (model# : AHT55T3, upto 300dC). - Below image is to show model# HMS-5300 + AMP55T, for low temp.
-
product
Electromagnetic Flowmeter for conductive liquids
Picomag
Reliable measurement and monitoring of industrial water, cooling water or warm water. Simultaneous measurement of flow and temperature. Flexible integration into all fieldbus systems via IO-Link. Commissioning and operation via Bluetooth® and SmartBlue App. Minimum conductivity ≥20 μS/cm. Fluid temperature –10 to +70 °C (+14 to +158 °F).
-
product
Fiber Assembly Eccentricity Measurement Instrument
KONCENTRIK V2
Multi-functional system for test and measurement of fiber optic ferrules & cable assemblies. Fast and automated measurements of eccentricity.
-
product
EMC Test Equipment
TDEMI G series
TDEMI stands for a novel generation of EMI measurement systems providing real-time analysis and enabling the user to perform high-quality emission measurements in a fractional amount of time compared to conventional EMI receiver technology. Ultra-fast Analog-to-Digital Conversion as well as real-time signal processing allows to emulate the behavior of instruments like oscilloscopes, receivers and spectrum analyzers. Due to the TDEMI's powerful signal processing hardware platform, corresponding to a computation power of approx. 80 conventional. PCs, such measurements are extremely fast in comparison to state of the art solutions.
-
product
Hardware and Software System
GeoRad
The "GeoRad" hardware and software system (hereinafter called HSS) is intended to measure ambient dose equivalent rate (DER) of gamma radiation and to pick up geographical coordinates and current time from navigation satellites, to display geo-referenced measurement results on the monitor of personal computer (PC), as well as to archive the information.
-
product
EZL Viscosity Mounting System
Sample handling and probe mounting may often be the deciding factors in a successful viscosity measuring system. The EZL Viscosity Mounting System provides an excellent mounting platform for in-line viscosity measurement with the Dynatrol® DV Viscosity Probes.
-
product
Engine Ignition Analyzer
GTC505
The GTC505 Engine Ignition Analyzer is a handheld instrument designed from the ground up for the diagnosis and performance measurement of all types of spark ignition systems, from conventional to the newest Coil on Plug in use.
-
product
Force Measurement Systems
Micro Edge Electronics Private Limited
As a reputed organization, we are engaged in manufacturing, importing as well as supplying a quality range of Force Measurement System. All these products are manufactured using high quality ingredients sourced from reliable vendor of the industry. These products are extremely rigid in state and ensure longer operational life. A team of skilled engineers and efficient technicians manufacture these products.
-
product
Economical Load and Force Measurement
ELF
Tekscan's ELF force and load measurement system matches the market's need for an inexpensive load and force measurement system with Tekscan's ability to deliver innovative load and force measurement solutions. The system consists of data acquisition hardware, software, and FlexiForce B201 sensors.
-
product
Flush Diaphragm Pressure Sensors
For high-frequency pressure measurements or in applications with severe space limitations, Honeywell Sensotec offers subminiature flush diaphragm pressure sensors in ranges from 0100 psi to 020,000 psi (010 to 01,400 bar). All-welded, machined stainless steel sensing diaphragms ensure ruggedness. Bonded piezoresistive and metal foil strain gauges offer high reliability. Millivolt and optional high-level outputs are compatible with most data acquisition systems.
-
product
Flow Sensors
Rugged and precise – flow measurement technology from SICKSICK provides innovative sensor solutions for flow measurement technology which combine flexible measuring methods and rugged equipment design with cost-efficient connection concepts to integrate higher-level systems. Whether you need to detect the current flow rate value using analog values or find the quantity using pulse detection – SICKs flow sensors are always reliable and safe and can work with a wide range of media under difficult process and ambient conditions.
-
product
Electrometer
SuperMAX
The SuperMAX Electrometer features two measurement channels with independent control over range, bias voltage, and applied system factor.
-
product
Hall Effect Measurement system
HMS-3000
Hall Effect Measurement System is very useful for measuring Carrier Concentration, Mobility, Resistivity and Hall Coefficient that should be pre-checked in order to grasp the electrical specifications of semiconductor device. Therefore, it is essentially required system to understand the electrical characteristics of semiconductor device.Ecopia’s HMS series consist of constant current source , terminal conversion system by Van der Pauw technique, low temperature(77K) test system and magnetic flux density input system. So, it is well-established system that has all the things needed to Hall Effect Measurement System.
-
product
Hall Effect Measurement system
HMS-5000
Constant current source + Van der Pauw method terminal conversion system
-
product
High Performance Liquid Chromatograph Triple Quadrupole Mass Spectrometer
LCMS-8050
Thanks to a heated ESI probe and the UFsweeper III collision cell, the LCMS-8050 achieves a level of sensitivity 30 times that of the LCMS-8030.The UF Technology, the ultrafast measurement technology built into the LCMS-2020 has further evolved, so measurements can now be performed even faster, without sacrificing data quality. At the same time, more compounds can now be measured in simultaneous qualitative and quantitative analysis. The system can be used in a wide range of fields for a variety of applications, such as quantitative analysis which requires high sensitivity, multicomponent simultaneous analysis, and screening.
-
product
LabVIEW Professional Development System
ntegrate hardware from a variety of measurement instruments and devicesIntuitive graphical programming syntax to simplify automationBuild custom user interfaces for engineering applicationsBuilt-in algorithms for signal processing, analysis, math, and PID controlSoftware engineering tools to debug, validate, and deploy codeOne-year SSP membership for technical support, online training, and software upgrades
-
product
In-Sight Vision Systems
9000 Series
The In-Sight 9000 is a rugged, ultra-high-resolution line of standalone vision systems. With its ability to acquire and process exceptionally detailed images, the In-Sight 9000 delivers high accuracy part location, measurement, and inspection over a large area—even when mounted at longer distances. Line scan and area scan image acquisition options are available for imaging continuously moving or stationary objects. Plus, a full suite of vision tools configurable through the In-Sight EasyBuilder interface solves a wide range of applications across industries.
-
product
Machine Vision System
CVX Series
he CVX Series is loaded with powerful features that support GLOBAL STANDARDS in machine vision inspection. State-of-the-art algorithms, that can be set by any user, ensure quick setup and long-term reliability. The best solution can be selected from a variety of options. No experience required to select lighing! - newly-developed, revolutionary Lumitrax function. 3D measurement. Ultra high-resolution 21 megapixel camera
-
product
Laser power meter
LM 100
This read out unit is designed to measure the output power of different lasers in combination with a thermophile head. The maximum power is limited by the power head used. Normally, the time constant of a power head is in the region of 15 to 25 seconds. Use of the read out unit enables reduction of the time constant of the whole measurement system to one second.?
-
product
Isoperibol Calorimeter
AC500
The AC500 determines calorific value, a key indicator of quality and value in solid and liquid fuels, through measurement of the heat released after combustion of a sample. This stand-alone benchtop unit uses a fully-integrated circulation system for a compact footprint—no additional heaters or coolers required. An integral water-measuring station simplifies sample preparation, and a Windows®-based operating system uses an electronic thermometer accurate to 0.0001°C to measure temperature every six seconds. Two-channel correction is possible through constant temperature monitoring in both the outer jacket and the calorimeter proper.
-
product
Integrating Spheres
All our spheres can be coupled to our high performance spectroradiometer systems for UV-visible-IR spectral power distribution measurements yielding full colour information including colour rendering indices, chromaticity co-ordinates, colour temperature, etc. Alternatively precision photometric detectors can be fitted for direct total lumen output measurements.
-
product
Isothermal Titration Calorimeters
MicroCal ITC Range
The "Gold Standard" for measuring binding affinity and stoichiometry. MicroCal ITC isothermal titration calorimeters are used to study a wide range of biomolecular interactions. The applications range from drug design to fundamental research such as the understanding and regulation of signal transduction pathways. These systems deliver direct, label free and in-solution measurements of binding affinity and thermodynamic parameters in a single experiment. They have high sensitivity, low sample consumption and options for automation to minimize ‘hands on’ time. A choice of instruments ensures that MicroCal ITC calorimeters meet the varied and demanding requirements of today’s life science laboratories.
