Showing results: 2416 - 2430 of 10455 items found.
-
DIS-RL series (05/2/6) -
Sugisaki Meter Co., Ltd.
Tightening and final check of screws and bolts. Separate type digital torque driver/wrench. The detection part is very compact, and it is effective for torque measurement in narrow places and minute torque measurement. Five channels of pass/fail judgment conditions can be saved, and settings can be made simply by switching channels even if the tightening conditions change.
-
N9000B -
Keysight Technologies
Master the essentials in signal characterization with the leading low-cost tool in signal analysis Perform cost-effective stimulus response measurements with the optional built-in tracking generator Add crucial functionality with X-Series measurement applications Enhance theory with practical skills when used with a training kit in your RF & microwave education lab
-
P9165A -
Keysight Technologies
P9165A 2x8 USB solid state switch matrix, 300 KHz to 6.5 GHz is a full cross-bar switch matrix that provides a switch based multiport VNA solution in the form of compact USB controlled involving larger scale of multi-DUT or multiport measurements such as 5G massive MIMO antenna measurement and others.
-
P9164B -
Keysight Technologies
P9164B 2X16 USB solid state switch matrix, 300 KHz to 9 GHz is a full cross-bar switch matrix that provides a switch based multiport VNA solution in the form of compact USB controlled involving larger scale of multi-DUT or multiport measurements such as 5G massive MIMO antenna measurement and others.
-
P9164A -
Keysight Technologies
P9164A 2X16 USB solid state switch matrix, 300 KHz to 6.5 GHz is a full cross-bar switch matrix that provides a switch based multiport VNA solution in the form of compact USB controlled involving a larger scale of multi-DUT or multiport measurements such as 5G massive MIMO antenna measurement and others
-
P9165B -
Keysight Technologies
P9165B 2X8 USB solid state switch matrix, 300 KHz to 9 GHz is a full cross-bar switch matrix that provides a switch based multiport VNA solution in the form of compact USB controlled involving larger scale of multi-DUT or multiport measurements such as 5G massive MIMO antenna measurement and others.
-
86120D -
Keysight Technologies
For the measurement of light sources and signals in wavelength ranges from 700 nm to 1700 nm, the 86120D Multi-Wavelength Meter offers a compelling set of features. With 1.5 ppm accuracy (typical 1 ppm) and a measurement cycle time of just 0.6 seconds, it is ideal to achieve fast, automated wavelength adjustment procedures.
-
LI-7820 -
Li-Cor Environmental, Inc.
The LI-7820 N2O/H2O Trace Gas Analyzer offers high-precision nitrous oxide measurements in a low power, portable design—enabling it to easily integrate into survey and long-term soil flux systems. Pair it with the LI-7810 CH4/CO2/H2O Trace Gas Analyzer or LI-870 CO2/H2O Analyzer for CO2 and CH4 measurements at your site.
-
ENDA-7000 Series -
HORIBA, Ltd.
After decades of experience in precise stack gas measurement, HORIBA's brand new ENDA series represents the ultimate stack gas analyzer. With enhanced lower cost and reduced maintenance time, high sensitivity, and usability, we focused on the users' point of view. The ENDA-7000 is designed to continuously measure the concentrations of NOX, SO2, CO, CO2, O2, and NH3 in stack flue gas streams. The model is offered in dozens of combinations based on your measurement requirements. The ENDA-7000 uses an extractive method which measures undiluted sample gases, and is very suitable to stack gas measurements such as shale gas, LNG, or biogas and other combustion applications. The ENDA-7000 is an excellent choice for measurements in power generation facilities, boilers, furnaces, steel manufacturing, cement plants, pulp and paper mills, etc.
-
M+P International
m+p Analyzer systems are available for field and laboratory use from 4 to many hundreds of measurement channels. From gathering simple time history data to narrowband (FFT) spectra, fractional octaves, wavelets, shock response spectra and much more, m+p Analyzer real time analyzers can be used with a wide range of instrumentation hardware including our own m+p VibPilot, m+p VibRunner and m+p VibMobile systems, National Instruments (CompactDAQ USB, PCI, PXI) and VTI Instruments (PCI). Low cost portable instruments to systems for distributed measurements can be configured for maximum flexibility. Measurement data from all sources are stored in a common format so it is easy to compare and handle results from any measurement source.
-
NI
The C Series Digitizer Module takes both high-speed and high-resolution time- and frequency-domain measurements. It features up to four channels that can sample at speeds up to 20 MS/s—ideal for discrete detection of signals 10 MHz and smaller for applications such as fault detection, partial discharge analysis, and acoustic measurements. The module's store-and-forward architecture allows up to 128 Mbits of measurement data to be sent back to the CompactRIO Controller and analyzed. You can use the module as part of a CompactRIO system and use the LabVIEW FPGA Module to develop an advanced trigger based on low-speed streaming for added flexibility. This digitizer includes the NI-DAQmx driver and configuration utility that simplifies configuration and measurements. NI-DAQmx supports NI programming environments and Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
OAKTON Instruments
These pocket-sized testers have a replaceable single-junction sensor which can be easily switched out, allowing you to save money by using the tester body over and over again. A large LCD makes viewing measurements easy and features a three-color backlight indicating operational mode—blue for measurement, green for calibration and red for alarm condition. Additional features include hold function to lock in measurements, self-diagnostic error message, and status icons for measurement stability and low battery voltage. The IP67-rated housing features an easy-to-grip design and floats if accidentally dropped in water when sensor cap is on. Powered by four AAA batteries, the testers can operate up to 400 hours continuously. To conserve power, the unit will auto power-off after 8 minutes of nonuse.
-
781425-01 -
NI
1‑Slot, USB CompactDAQ Chassis - The cDAQ‑9171 is a bus‑powered, CompactDAQ USB chassis designed for small, portable sensor measurement systems. The chassis provides the plug‑and‑play simplicity of USB to sensor and electrical measurements. It also controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The cDAQ‑9171 also has four 32‑bit general-purpose counters/timers that you can access through an installed, hardware‑timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement.
-
Ingenieurbüro Mencke & Tegtmeyer Gm
For numerous applications in photovoltaics at research, development and production, we offer different characteristic measuring devices. From the simple handheld instrument for PV modules, very precise and convenient laboratory instruments for cell and module measurement to fully automated PV module test stands for long-term measurement greater number of PV modules.
-
UNION INSTRUMENTS
The pressure test kits of the DPK3 R1 and DPK3 R2 series are used to perform leak tests on pipelines and fittings. A data logger for pressure and temperature measurements logs the test pressures and temperatures. A test report is created at the construction site via a battery-operated printer. The measurement data can be transferred to a PC for further archiving and evaluation.