Filter Results By:
Products
Applications
Manufacturers
-
product
ELECTRICAL TEST Kit
1021 TK
Standard Electric Works Co., Ltd
2950 CL ● Pocket size.● 4000 counts.● Full automatic measurement : Voltage measurement. Current measurement. Resistor measurement.● Data hold function.● Continuity check.● Diode measurement.● Select function.● Low battery indication.● Auto off function.● Flashlight (auto off in 1 minute). ALS-2 ● Use with any clamp meter.● x10 mode allows for more accurate measurements of low amperage devices.● x1 mode allows for direct reading.● 4mm voltmeter input jacks.● Integrated ground conductor.● 10 amp capacity.● 10cm plug cord for greater flexibility.
-
product
TRUE RMS AC Clamp Meter
2960 CL
Standard Electric Works Co., Ltd
● True RMS measurement.● Pocket size.● 4000 counts.● Full automatic measurement. Voltage measurement. Current measurement. Resistor measurement.● Data hold function.● Continuity check.● Diode measurement.● Select function.● Low battery indication.● Auto off function.● Flashlight (Auto off in 1 minute).● Re-power on by pushing any of the push buttons or by changing the rotary switch mode after auto power off.
-
product
Digital Milliohm Meter
4538 mO
Standard Electric Works Co., Ltd
● 4-Wire method for mΩ measurement.● Measures down to 100µΩ (0.1mΩ).● Maximum resolution of 100µΩ.● 4 Lines × 20 Characters large LCD.● 200 measurement results can be saved in the memory and recalled on the display. ● Auto power off.● Data hold function.● MAX/MIN function.● Power source: 1.5V "C" battery × 8● Long battery life and stable power. ● Low battery indication.
-
product
Non-Contact Type Phase Sequence Indicator
890 PR
Standard Electric Works Co., Ltd
● The 890 PR is a Non-Contact phase detector with flashing LEDs and a beeping buzzer to show the detection of AC 3-phase sequence.● Two functions in one unit : open phase and phase sequence detection.● Convenient brightness switch to make the indication visible in dim areas or sunlight.● Back cover magnets which attach the instrument to the AC distribution panel offer easy measurement. ● 3-Phase AC 75 to 1000V is fitted for detection.● Conductor size: 1~35mm● Detect frequency range is from 45 to 65Hz.
-
product
Digital Multimeters
ST-3201
Standard Electric Works Co., Ltd
● Display : 3½ digit liquid crystal display (LCD) with max. reading of 1999.● Polarity : Automatic, (-) negative polarity indication.● Zero Adjustment : Automatic.● Over Range Indication : Highest digit of (1) or (-1) is displayed. ● Low Battery Indication : The (BAT) is displayed when the battery voltage drops below the operating voltage.● Measurement Rate : 3 measurements per second, nominal.● Operating Temperature : 0ºC ~ 50ºC, 70% R. H.● Storage Temperature : -20ºC ~ 60ºC, 80% R. H.● Accuracy : Accuracy specifications at 23 ± 5ºC, less than 75% R. H.● Power : Single, 006P 9 volt battery● Dimensions : 128(L) × 72(W) × 33(D) mm.● Weight : Approx. 183g
-
product
AC Clamp Meter
2950 CL
Standard Electric Works Co., Ltd
● Pocket size.● 4000 counts.● Full automatic measurement. Voltage measurement. Current measurement. Resistor measurement.● Data hold function.● Continuity check.● Diode measurement.● Select function.● Low battery indication.● Auto off function.● Flashlight (Auto off in 1 minute).
-
product
Analogue Mulitimeter
ST-367TR
Standard Electric Works Co., Ltd
● Easy to read 3-color scale...for mistake proof reading.● Mirror scale...makes reading pointer easy.● Safety fused...on all ranges.● Diode protected meter...prevents damage due to overload.● Safety features...safety fused, safety "OFF" position.● hFE and db measurement.● With stand...makes reading and measuring easy.
-
product
AC/DC Clamp Meter
2660 CL
Standard Electric Works Co., Ltd
● 4000 counts.● Voltage measurement, current measurement, resistor measurement, frequency counter, capacitor measurement.● Bargraph indication.● Range change function.● Data hold function freezes the reading.● REL function.● Peak function.● Diode measurement.● Max / Min function.● Continuity check.● Low battery indication.● Auto Power Off (APO) function.● Safety design throughout with no exposed metal parts, shielded banana plugs and recessed input terminals.
-
product
AC Clamp Meter
2940 CL
Standard Electric Works Co., Ltd
● Pocket size.● 4000 counts.● Full automatic measurement. Voltage measurement. Current measurement. Resistor measurement.● Data hold function.● Continuity check.● Diode measurement.● Select function.● Low battery indication.● Auto off function.● Flashlight (Auto off in 1 minute).
-
product
Telescopic Hot Stick
HS-175
Standard Electric Works Co., Ltd
● Triangular-shaped design keeps the sections aligned during extension and retraction.● Push button release for stick extension and retraction. ● Telescopic design allows for easy assembly, storage and transportation.● Withstands voltage rating of 100kV from 30cm for 1 minutes. ● Universal end fitting accepts a wide variety of standard attachments.● Highly visible yellow tip section.● Easy-to-replace sections.● Carrying bag included. ● Optional integrated height measurement scale.● Complies with IEC 62193 safety standard.
-
product
Milliohm Meter
4137 mO
Standard Electric Works Co., Ltd
● Protection class: IP66 (Lid closed)● Microprocessor-controlled.● Four terminal measurement.● Measures down to 100μΩ.● 5 Ranges from 200.0mΩ to 2000Ω.● Maximum resolution of 100μΩ.● Three test currents with over-temperature protection.● Protection against inadvertent connection to over voltage.● Large LCD.● Potential lead resistance and current lead resistance checks.● "Full-featured” EnerSave inside.● EnerSave Auto hold.● EnerSave Auto off.● Lightweight, robust & compact.● Indicators show if reading may be invalid (RP, RC, and temperature).● "O-Ring” sealed case.
-
product
AC Line Separators
ALS-1
Standard Electric Works Co., Ltd
● x10 Model allows for more accurate measurements of low amperage devices.● Direct reading x1 mode.● 4mm Voltmeter input jacks.● Intergrated ground conductor.● 10 amp capacity.
-
product
Telescopic Hot stick
HS-178
Standard Electric Works Co., Ltd
● Triangular-shaped design keeps sections aligned during extension and retraction● Push button release for stick extension and retraction ● Telescopic design allows for easy assembly, storage and transportation● Lower push button fix position for better support of the telescopic hot stick● Withstands voltage rating of 100kV from 30cm for 5 minutes ● Universal end fitting accepts a wide variety of standard attachments● High-visibility yellow tip section● Easy-to-replace sections● Carrying bag included ● Optional integrated height measurement scale● Complies with IEC 62193 safety standard
-
product
Measurement
Field Uniformity
The purpose of our measurement is to characterise the properties (uniform field area, UFA) of the anechoic room according to IEC 61000-4-3 Ed. 3.1 b or EN 61000 4 3.
-
product
Measurement
Site VSWR
The Site VSWR measurement is done according to CISPR 16-1-4 in the frequency range from 1 GHz to 18 GHz using broadband omni directional antennas in horizontal and vertical polarisation. The volumetric test method is applied (test volume needs to be specified), test distance 3 m - any other distance upon request. The ground plane has to be covered with absorbing material.
-
product
Validation
Freespace VSWR
The Free Space VSWR validation is done according to J.S. Hollis, T.J. Lyon, L. Clayton: "Microwave Antenna Measurement", Scientific-Atlanta Inc., Atlanta, Georgia, USA, July 1970.
-
product
Measurement
Ambient Noise
The Ambient Noise (AN) measurement is done in accordance with CISPR 22 and EN 50022
-
product
Precision Conical Dipole
PCD 8250
Exposure evaluation next to mobile communication facilities e.g. GSM and UMTS base stations. Accurate RF radiation safety measurements e.g. nearby broadcast stations or in buildings. All kinds of field strength measurements where high precision, a wide frequency range and small antenna dimensions are required. Measurements according to our Field Nose method. Frequency range: 80 MHz 3 GHz
-
product
Comb Generator
RefRad X
A comb generator is built inside a conical antenna element. Therefore no cable between antenna and generator is required. Thus leads to repeatable measurement results and reliable simulation of radiation performance.Optionally a fibre link for synchronisation with the receiver is used.Frequency Range 10 kHz - 3 GHzFrequency Spacing 10 kHz, 1 MHz, 5 MHz
-
product
Precision Conical Dipole
PCD 3100
Site validation measurements according to prEN 50147-3 in fully anechoic rooms. Accurate RF radiation safety measurements (e.g. broadcast stations). All purposes of broadband precision field-strength measurements. Frequency range: 30 MHz - 1 GHz
-
product
FilmPro Infrared Transmission Gauge
Nordson Measurement & Control Solutions
High-Performance Basis Weight and Thickness Measurements for Film, Sheet and Coatings
-
product
Pipe Crawlers
Advanced Inspection Technologies Inc.
AIT offers a full range of robotic cctv crawlers for the inspection any pipe or hazardous space as large as 2000mm (6.5 Ft.). Our smallest industrial Rovver can navigate spaces and pipelines as small as 100mm (4 in.). Pan tilt and zoom cameras, a wide selection of wheels for a variety of applications, laser measurement, sonde locator and more feastures. Your inspection is displayed on a modern touch screen display that is ergonomic and portable. Many pipe inspection camera robots offer ATEX Zone 1 (Division 1) EX Rating.
-
product
Bench-Top Spectrophotometers
Konica Minolta Sensing Americas, Inc
Konica Minolta Sensing’s high precision bench-top spectrophotometers are ideal for measuring the color and appearance of opaque, transparent, translucent, and fluorescent samples under various illuminants within laboratory environments. Our instruments deliver accurate measurement data so users can formulate, evaluate, and control color more efficiently. To find which solution best fits your application and operational needs, please browse through our selection of bench-top spectrophotometers below.
-
product
Integrating Spheres - Luminous Flux Measurement For LEDs And Lamps
Konica Minolta Sensing Americas, Inc
One of the most important tests in light measurement is the assessment of the total radiant power or luminous flux of light sources using integrating spheres. An integrating sphere’s inside surface is coated with a diffusely reflecting material which guarantees complete integration and homogenization of the emitted radiation. The integrated light is then measured at the detector port.
-
product
Light Booths
Konica Minolta Sensing Americas, Inc
Konica Minolta’s Light Booth products provide accurate results when inspecting a range of unique products including inks, paints, plastics, textiles, paper and colorants. Light booths simulate lighting conditions which allows testing in a multitude of different lighting conditions. This allows for incredibly precise color measurements in a spectrum of different lights and angles.
-
product
Reference Systems For UV-LED Production
Konica Minolta Sensing Americas, Inc
UV-LED lab measuring stations are for testing new products or, e.g. building reference systems for UV-LED production. In order to cater for new measurement scenarios, the individual system components of the high-end portfolio from Instrument Systems are subject to ongoing technological improvement. -
product
Integrating Spheres For UV
Konica Minolta Sensing Americas, Inc
Instrument Systems offers complete measurement solutions for UV-A, -B and -C radiation starting from 200 nm. The operation of the well-proven Instrument Systems spectroradiometers, e.g. CAS series, with integrating spheres made from PTFE facilitate high sensitivity measurements of UV radiant flux.
-
product
K-Type Thermocouples Wire, Fiberglass (32 deg F to 900 deg F) 1 m
745690-K001
K-Type Thermocouple, 32°F to 900°F Temperature Sensor - The K-Type Thermocouple works with NI measurement devices and software to help you acquire temperature data within a measurement system. You can use LabVIEW or FlexLogger software and NI-DAQmx driver software to configure measurements and predefined scaling coefficients for the K-Type Thermocouple and acquire synchronized temperature data in units of degrees. The K-Type Thermocouple is available in various lengths and configurations including field-cuttable, ready-made sensors, and thermocouple wire extensions with a -20°F to 221°F temperature range.
-
product
K-Type Thermocouples Wire, Fiberglass (32deg F to 900deg F) 2 m
745690-K002
K-Type Thermocouple, 32°F to 900°F Temperature Sensor - The K-Type Thermocouple works with NI measurement devices and software to help you acquire temperature data within a measurement system. You can use LabVIEW or FlexLogger software and NI-DAQmx driver software to configure measurements and predefined scaling coefficients for the K-Type Thermocouple and acquire synchronized temperature data in units of degrees. The K-Type Thermocouple is available in various lengths and configurations including field-cuttable, ready-made sensors, and thermocouple wire extensions with a -20°F to 221°F temperature range.
-
product
J-Type Thermocouples (Ungrounded) (32 deg F to 900 deg F )
745685-J02
J-Type Thermocouple, 32°F to 900°F Temperature Sensor - The J-Type Thermocouple works with NI measurement devices and software to help you acquire temperature data within a measurement system. You can use LabVIEW or FlexLogger software and NI-DAQmx driver software to configure measurements and predefined scaling coefficients for the J-Type Thermocouple and acquire synchronized temperature data in units of degrees. The J-Type Thermocouple is available in various lengths and configurations including field-cuttable, ready-made sensors, and thermocouple wire extensions with a -20°F to 221°F temperature range.
