Filter Results By:
Products
Applications
Manufacturers
-
product
Barometer-Manometer-Thermometer Data Logger
HD2114B.2
Barometer-Micromanometer-Thermometer with built-in barometric sensor (600…1100 mbar) for absolute, relative and differential pressure and temperature measurements.
-
product
Barometers
Barometer measures atmospheric pressure, barometer can also be used to measure altitude.Pressure measurement can predict short-term changes in the weather. Many measurements of air pressure are used as part of surface weather analysis. Modern barometers are very reliable and show good results.
-
product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J0
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J1
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K0
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K1
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
product
Battery Data Logging Device
FST-AM
Foresight Electronics Co., Ltd.
A data logger, is an electronic instrument that records measurements at set intervals over a period of time. Depending on the particular data logger, measurements can include: air temperature, relative humidity, AC/DC current and voltage, differential pressure, time-of-use (lights, motors, etc.), light intensity, water temperature, water level, dissolved oxygen, soil moisture, rainfall, wind speed and direction, leaf wetness, pulse signals, room occupancy, plug load, and many more.
-
product
Battery Testers
Battery testers are designed for the new measurement requirements of the battery industry. They are special for measurement use in low-resistance batteries, large-scale lithium battery packs and fast product sorting in production lines.
-
product
Bedrock Intelligibility Measurement Kit
This kit contains all you need for speech intelligibility measurements using the STIPA method according to most national and international standards, including the following:*IEC-60268-16*ISO-7240-19*NFPA72 Annex D*NEN2575*DIN-60849/DIN-VDE-0833-4*BS-5839-8
-
product
Bench Digital Multimeter
8012
Model 8012 is a high performance, 20,000-count digital benchtop multimeter. It measures DC and AC voltage, DC and AC current, Resistance, Capacitance, Hz, hFE, Diode, and Continuity. 8012 features a large 4-1/2 digit LCD display with backlight. Maximum voltage measurement is up to 1,000V DC and 750V AC with resolution up to 10 µ V. Maximum current measurement is up to 20A. AC measurement is performed by high accuracy RMS.
-
product
Bench Digital Multimeter, 3.8, USB, 20 A, 1 kV, 60 Mohm
72-13620
*True RMS bench top digital multimeter with 6000 counts display*CAT II 600V safety rating*Manual function select and auto ranging*Transistor & SCR measurement*Data hold, max/min modes*EBTN (Enhanced Black Twisted Nematic) LCD backlight*USB interface*Input protection*Powered by 100V/120V/220V/240V ±10%, 47Hz to 63Hz supply*12-month limited warranty *view Terms & Conditions for details
-
product
Bench Digital Multimeter, Calibrated, 1 kV, 10 A, 3.8 Digit
72-1015 CAL
The 72-1015 CAL from Tenma is a digital bench type true RMS multimeter. It has auto and manual range options with maximum reading of 5999 counts and 3-5/6 digits which has a unique outlook design. In addition to all the conventional features including DC/AC voltage, current, resistance, diode, continuity test, diode test capacitance, temperature, transistor, max/min, there is a data hold, low battery display, sleep mode, RS232C serial port for easy connection with computer to realize macro recording, monitoring and capture of transient dynamic data, displaying change of waveform during the measurement, providing data and evidence to engineering technicians for scientific research. This meter complies with the standards IEC61010, pollution degree 2, overvoltage category (CAT I 1000V, CAT II 600V) double insulation and CE marked.
-
product
Bench Digital Multimeter, Calibrated, Data, 1 kV, 10 A, 3.8 Digit
72-1015 CAL D
The 72-1015 CAL D from Tenma is a digital bench type true RMS multimeter. It has auto and manual range options with maximum reading of 5999 counts and 3-5/6 digits which has a unique outlook design. In addition to all the conventional features including DC/AC voltage, current, resistance, diode, continuity test, diode test capacitance, temperature, transistor, max/min, there is a data hold, low battery display, sleep mode, RS232C serial port for easy connection with computer to realize macro recording, monitoring and capture of transient dynamic data, displaying change of waveform during the measurement, providing data and evidence to engineering technicians for scientific research. This meter complies with the standards IEC61010, pollution degree 2, overvoltage category (CAT I 1000V, CAT II 600V) double insulation and CE marked.
-
product
Bench Digital Multimeter, Calibrated D & U, 1 kV, 10 A, 3.8 Digit
72-1015 CAL DU
The 72-1015 CAL DU from Tenma is a digital bench type true RMS multimeter. It has auto and manual range options with maximum reading of 5999 counts and 3-5/6 digits which has a unique outlook design. In addition to all the conventional features including DC/AC voltage, current, resistance, diode, continuity test, diode test capacitance, temperature, transistor, max/min, there is a data hold, low battery display, sleep mode, RS232C serial port for easy connection with computer to realize macro recording, monitoring and capture of transient dynamic data, displaying change of waveform during the measurement, providing data and evidence to engineering technicians for scientific research. This meter complies with the standards IEC61010, pollution degree 2, overvoltage category (CAT I 1000V, CAT II 600V) double insulation and CE marked.
-
product
Bench Ion/pH/mV RS232 Meter
CyberScan pH 2100
High Resolution and Accuracy (Up to ±0.002 pH Accuracy) for precise measurementBacklit Two Line, Dot Matrix LCD Display provides clear instructions for setup, measurement and calibration
-
product
Bench Multimeters
PeakTech Prüf- und Messtechnik GmbH
The versatile functions are completed by the true rms measurement, the temperature and the 3-wire resistance thermocouple measurement.
-
product
Bench pH/Conductivity/TDS Meter
CyberScan PC 510
Multi-parameter meters measures pH, Conductivity and TDS in single meter User-Customization for more accurate measurements with programmable functions like stability, electrode diagnosis - pH slope/offset/mV base value, etc.
-
product
Bench pH/mV RS232 Meter
CyberScan pH 1100
High Resolution and Accuracy (Up to ±0.002 pH Accuracy) for precise measurementBacklit Two Line, Dot Matrix LCD Display provides clear instructions for setup, measurement and calibration
-
product
Bench/portable Universal Counters With USB Interface 3GHz Or 6GHz
TF900 Series
Frequency, period, pulse width, frequency ratio, duty cycle, and event counter modesDC to 3000 or 6000MHz range, 0.001mHz resolutionHigh impedance measurement up to 125 MHzAC or DC coupling, 1M/50Ohm selection, polarity invertSwitchable attenuator, threshold controlNoise filter for low frequency measurementsSelectable measurement time; display hold functionLarge 10 digit display with full range of annunciatorsInternal rechargeable batteries for portable useUSB interface provides full remote control and readback
-
product
Bench Power Supply, DC, Single, Adjustable, 1 Output, 1 V, 36 V, 0 A, 3 A
72-8345A
Switch Mode Laboratory DC Power Supplies Precision adjustable supply provides adjustable 1~36VDC output with adjustable current limiting from 0~3A. It is ideal for test, measurement and service applications where tight voltage and current regulation are critical. Highly efficient switch mode design delivers outstanding performance from an extremely compact footprint. Unique separate output ON/OFF control allows voltage and current setting, with the supply output turned off. Part of a Complete Series, this slim supply occupies little bench space while providing very high precision and 90W of continuous output.
-
product
Benchtop Analyzer
LabSpec 4 Bench
Analytical Spectral Devices, Inc.
Configured specifically for fixed-location analysis with AC power, the LabSpec 4 Bench benchtop analyzer provides all the performance of ASD's LabSpec laboratory spectrometer line in a space-saving and cost-efficient design. The benchtop analyzer features sophisticated near infrared (NIR) spectroscopy at a 10 nm resolution for accurate measurement of a wide variety of materials in real time. Like the portable models, an enhanced spectrometer configuration more than doubles the signal-to-noise performance in the SWIR regions.
-
product
Bench-top Digital Power Meter
GPM-8213
GW Instek GPM-8213 power meter is designed specifically for single-phase (1P/2W) AC power supply’s power measurements. Powerful features, including 4” TFT LCD, five-digit measurement display, 19 power measurement parameters, integral measurement function, high-accuracy voltage/current/power measurement capabilities, front/rear panel input terminals, and various communications ports, are to facilitate users with clear, convenient, and accurate power measurements.
-
product
Benchtop Goniometer
This small goniometer has the capability not to only fit into almost every optical laboratory, but also to provide measurement data on concise level. The type C set up of this instrument enables the developer of single LEDs, LED modules or chips to study angular performance in many development stages; fast and most important: reliable. The detector head of the goniometer is a high-quality, visible-range spectrometer, equipped with diffuser optics to collect all important measurement quantities over the customer required angular range. With a maximum allowable source sample size of 300mmx100mm and 25kg, the new benchtop goniometer covers a wide range of LED measurement requirements. The footprint of the instrument itself with 1.65mx0.60mx1.73m allows the usage also in small dark rooms and optical laboratories.
-
product
Benchtop Metrology Solution
FilmTek 2000 PAR-SE
Scientific Computing International
Our most advanced benchtop metrology solution, engineered to meet the needs of nearly any advanced thin film measurement application, from R&D to production. Combines spectroscopic ellipsometry and DUV multi-angle polarized reflectometry with a wide spectral range to deliver the highest accuracy, precision, and versatility in the industry. Patented parabolic mirror technology allows for a small spot size down to 50µm, ideal for direct measurement of product wafers and patterned films.
-
product
Benchtop NMR Analyser
MQC+
MQC+ benchtop NMR (Nuclear Magnetic Resonance) analyser for the measurement of oil, water, fluorine and solid fat in a variety of samples in a wide range of industries. The MQC+ replaces wet chemical analysis, which uses hazardous chemicals, and allows the measurement of more samples much faster. Unlike wet chemical methods, the MQC+ does not destroy the sample being measured. It can also measure physical properties including crystallinity and density of polymers.
-
product
Bench-Top Type ASE Light Source
ASE(Amplified Spontaneous Emission) light sources are low-coherent light sources ,which combines the both features of high intensity like laser and broad spectrum like LED. Output stability is greater than those of LD and LED, and therefore they are suitable for high accuracy measurement applications. With the use of rare-earth-doped fluoride fibers, the plentiful lineup of FiberLabs light sources includes the 540 nm-, 850 nm-, 1300 nm-, 1480 nm- and SCL-bands that other companies do not provide.They are the best light sources for FBG sensors, OCT, fiber optic gyroscopes, gas sensors, and fluorescence excitation, as well as for measurement of optical components. The bench-top type is easy to use as a stand-alone light source and the modular type is convenient for integration into equipments.
-
product
Benchtop Vision Measurement System
HVR-Flip
The HVR-Flip large field-of-vision (FOV) Benchtop Vision Measurement System has the unique characteristic of being used in either a vertical or horizontal format offering tremendous versatility and value. Rapidly measure parts up to 3.65 x 3"Working distance of 10". Measure a single feature, an entire part, or multiple parts. MetLogix™ M3 software allows for easy one-touch feature measurement. Auto-detect part recognition.
-
product
Bespoke
KP Technology has a sound background in scientific measurement and instrumentation, including first-hand experience in the requirements of the scientific community. Our wealth of experience, from the needs of the user through the design process and on to manufacture, is invaluable to our working methods and practice.
-
product
Binocular and Mobile Vision Screener
2WIN
2WIN is a mobile and binocular vision screener that measures both eyes at the same time, in real life vision conditions. It embodies the best and the most complete technologies to fully detect refractive errors, eye abnormalities and vision problems. It measures in the range of -15D to +15D for automatic measurement of dynamic pupils response to programmable light stimulations, and accurately center spectacle lenses. 2WIN is capable of detecting Myopia, Hyperopia, Astigmatism, and other Amblyogenic factors. Additionally, it will provide evidence of sight anomalies that may be related to anisometropia, anisocoria, strabismus, phorias.
-
product
Bioacoustic Analysis
SIGNAL 5
SIGNAL 4.0 provides a powerful graphical environment for viewing, measuring, and manipulating signals, while retaining all the programmability of SIGNAL 3.1. SIGNAL 4.0 is easy to learn and convenient to use. New features include multi-window graph displays with multiple measurement cursors and flexible zooms, drag-and-drop layout for publication graphs, an on-screen spreadsheet for screen measurements, a macro recorder for easy programming,
