Showing results: 721 - 735 of 757 items found.
-
Chroma 87001 -
Chroma Systems Solutions, Inc.
Chroma 87001 Battery Cell Simulator is a high precision, programmable, and bidirectional DC power source with both voltage source and current source functions. In addition, the model can be used as a multi-channel DC power supply or an electronic load as well. A single simulator has 16 channels and each of them can set voltage and current respectively via Chroma software.
-
DT4 -
North Atlantic Industries
The DT4 module (the enhanced version) features 24 programmable channels for either input (voltage or contact sensing with programmable, on-module pull-up/pull down current sources), or output (current source, sink, or push-pull) up to 500 mA per channel from an applied, external 3 – 60 VCC source. These modules can sense broken input connections and whether an input is shorted to +VCC or to ground. Additional features of the DT4 (Enhanced Version) are listed below.
-
Electronic Test & Power Systems
A comprehensive range of high voltage power sources are available from ETPS. Product families range from programmable high precision laboratory power supplies to HV Cassettes and PCB modules.
-
YAVAP955 -
6TL Engineering
The YAV board AP955 contents 10 CAN Bus programmable bipolar Isolated precision and low noise 0 to 5VDC voltage sources up to 400mA output, with Tripaddle VPC connector.
-
AC3 -
North Atlantic Industries
The module is used to provide an AC signal source when a secondary reference source other than the optional on-board reference module is required. The modules are programmable for full range voltage outputs from 2 to 115 VAC, and frequency from 47 Hz to 10 kHz.
-
AC2 -
North Atlantic Industries
The module is used to provide an AC signal source when a secondary reference source other than the optional on-board reference module is required. The modules are programmable for full range voltage outputs from 2 to 115 VAC, and frequency from 47 Hz to 10 kHz.
-
VX4616 -
VX Instruments GmbH
2 galvanically isolated bipolar output channelsFrequency bandwidth up to 150 kHzOutputs are operating as inverting precision power amplifierOutputs are operating as programmable DC source (voltage or current)Outputs are programmable or adjustable via an external analog sourceAuto sensing featurePulse modulation with extremely high slew rate
-
V460 -
Highland Technology, Inc.
The V460 is a VME-based versatile source/measurement unit. It includes a programmable constant-current source, a precision programmable gain 16-bit analog-to-digital converter, and a 4-wire, 16-channel analog multiplexer. An internal microprocessor supervises channel scanning according to user loaded parameters, reporting sensor voltage drops or, for selected sensor types, engineering-unit data.
-
APCI-3300-8 -
TEAM SOLUTIONS, INC.
18-bit resolution, unipolar, 16-bit accuracy 8 differential inputs for strain gauges Voltage range 0 to + 2.5 V 8 independant voltage sources for the connected pressure sensors Output voltage for the voltage sources 5 V, 40 mA Gain and offset calibration Calculation of the pressure value through software Programmable gain 16-bit accuracy with sample rates of 20, 40, 80 or 160 Hz 4 digital input channels, 24 V and 3 digital output channels, Open Collector, isolated
-
CBCT -
Manta Test Systems
The CBCT is a variable voltage DC power supply designed specifically to test substation circuit-breaker Open and Close coils. The CBCT uses the substation’s DC power supply to electronically generate a programmable output voltage from 5% to 95% of the source voltage. The CBCT can maintain up to an 80A test current while maintaining 2% or better voltage regulation during the circuit breaker coil operation.
-
VI-700 -
IET Labs
The VI-700 Voltage and Current Source is a versatile precision dialable or remotely programmable voltage and current source. Its three ranges provide up to 20 V full scale (200 V with the HV option), and down to 100 mV resolution; and 20 mA full scale down to 0.1mA resolution. Both voltage and current outputs are available simultaneously. The output is set by a range selector and thumbwheel switches in the LOCAL mode, or by a digital input at the rear panel. The REMOTE mode control can be a RS232 or IEEE-488 interface.
-
PLS Series -
IET Labs
The PLS Series is a broad line of high precision programmable decade inductors. They provide straight inductance in a wide selection of ranges, tolerances andratings. IET Labs also supplies custom combination substituters for capacitance and resistance as well as sources for voltage and current.
-
GX3348 -
Terotest Systems Ltd.
The GX3348 is a multi-channel analog I/O 6U PXI card which provides (3) programmable sources, and a 4 x 48 or 4 x 64 matrix - allowing the user to route the 3 sources, or ground to any of the 48 or 64 I/O channels. In addition, each I/O channel can be connected to a 16-bit A to D converter, providing DC voltage measurement capability for each channel.
-
DIGAMEL Subestaciones
The digital relay and meters test system type DRTS 34 is a programmable and automatic current and voltage source, that permits for the automatic test of digital protection relays, such as those used in Medium and High voltage networks, and of energy meters, power quality meters and transducers.
-
ET Power Systems Ltd.
A comprehensive range of high voltage power sources are available from ETPS. Product families range from programmable high precision laboratory power supplies to HV Cassettes and PCB modules. The flexible high voltage design platforms and responsive management structure enable us to offer an economically viable custom build. High voltage power supplies from ETPS are used in a variety of applications ranging from electron acceleration systems and mass spectrometers to magnetrons, x-ray and nuclear research.