Showing results: 826 - 840 of 1342 items found.
-
Circuit Assembly Corp.
All of our Solar Connectors are thoroughly tested and TUV 1500VDC and UL1000VDC approved. These connectors provide reliable, waterproof and anti-aging features, and are proven to withstand any heavy environmental conditions. Other Solar Connectors typically have a water permeability rating of 66 or 67. Our IP68 rating ensures that our Solar Connectors will hold up in the most severe environmental conditions including sand storms and water submersion up to 3 meters. Our solar connectors are compatible with any solar connectors in the industry. We have designed our connectors to complement other solar connectors as well as replace them. Whether you’re looking for solar connectors to use with your current ones or searching for solar connectors to start a project, our solar connectors will be right for you.
-
TC4047 -
Teledyne Marine RESON B.V.
The TC4047 miniature hydrophone offers a useable frequency range from 1kHz to 170kHz. The hydrophone incorporates a high quality 20dB low-noise pre-amplifi er which provides optimal conditions for signal transmission. The high sensitivity provides excellent signal to noise ratio and immunity against induced cable noise. The hydrophone is omnidirectional up-to 100kHz and has uniform receiving characteristic from 1kHz to 100kHz. An insert calibration circuit enables remote testing of the hydrophone condition. The hydrophone comes with a SEACON connector. The sensor element is permanently encapsulated in Special formulated NBR to ensure long term reliability. The rubber has been specially compounded to ensure acoustic impedance close to that of water. The strainrelief and outer jacket of the cable is made of high density polyurethane. TC4047 can be used in sea or fresh water.
-
VM-810 -
Vivax-Metrotech Corp
Using the correct frequency makes a world of difference when locating buried utilities. The depth of the utility, size, material, and amount of congestion (proximity of other utilities) all need to be taken into consideration for the correct frequency selection. Large diameter, direct buried pipes with bell housing ends that use insulators and rubber gaskets, such as water or gas require a higher frequency while smaller diameter, well-grounded direct buried or long distance in conduits work, better with a lower frequency. The VM-810 operates at 83.1kHz which is ideal for water and gas utilities which generally are larger pipes with bell housings and gaskets. The VM-810’s higher frequency is also good for locating ungrounded small diameter drop wires and inducing signals through the soil, onto services when direct connecting is not an option.
-
WB Series -
Magtrol Inc.
Eddy-Current Brake Dynamometers (WB Series) are ideal for applications requiring high speeds and also when operating in the middle to high power range. Eddy-Current Brakes provide increasing torque as the speed increases, reaching peak torque at rated speed. The dynamometers have low inertia as a result of small rotor diameter. Brake cooling is provided by a water circulation system, which passes inside the stator to dissipate heat generated by the braking power. The water cooling in the WB provides high continuous power ratings (max. 140 kW). The WB dynamometers have accuracy ratings of 0.3% to 0.5% full scale ( 2% for WB 2.7), depending on size and system configuration. Additional options include: high-speed version, speed pickup, mechanical rotor blocking device, OEM version IS and vertical mounting.
-
Apogee Instruments, Inc.
Calibrated to a custom black-body cone with a measurement uncertainty of 0.2 C from -30 to 65 C when the sensor (detector) temperature is within 20 C of the surface (target) being measured. Radiometers are only sensitive from 8 to 14 m (atmospheric window) to minimize the influence of water vapor and CO2 on the measurement.
-
HR-480 -
HORIBA, Ltd.
HR-480 industrial residual chlorine meter takes sequential measurements of free residual chlorine, which is an indicator used in the inspection of the anti-bacterial properties of drinking water and swimming pools.The sensor(RS-1) combined with uses a galvanic method with no drive section, making it highly maintainable, and producing stable measurements over a long period.
-
X100L Series -
Mosebach Manufacturing Company
Introducing Mosebach’s X100L load bank. One of the lightest dual voltage, 100 kW load banks on the market! The unit weighs approximately 64 lbs. and has 5 kW resolution. The X100L load bank includes an Industrial strength, injection molded, 100% water proof case with wheels as shown below.
-
mks Ophir
Ophir has a number of ways to measure high laser powers up to 12kW without heavy water cooled equipment. Most of today’s lasers can be set to emit for a short, precisely controlled period of time. If a short exposure to the laser of 0.3 – 10s is sufficient to measure the power then there are compact, uncooled sensors available for this purpose.
-
DewTrak II -
Edgetech Instruments
The DewTrak II uses the chilled mirror dew point temperature condensation principle to determine the water vapor concentration in gas mixtures, and a platinum resistance thermometer to accurately measure that temperature. Outputs include 4 to 20mA, 0 to 5 Vdc, or 0-10Vdc and an RS232 serial port as well as electrically isolated relay contacts.
-
ORP57 -
Milwaukee Instruments
The Milwaukee ORP57 PRO ORP/Temp. Tester is designed for laboratory, pools, education, water treament and many other applications. It is the ideal meter to help make sure that your ORP/Temp. needs are being met and are reliable results for your analysis. Keep ORP/TEMP. in your target range to help your achieve best results.
-
Chrome Series -
Equus Products, Inc.
This attractive, durable, and affordable Equus 7000 Classic 2 in. mechanical temperature gauge features elegant styling, superior 270 degree sweep for enhanced resolution, black dial, chrome bezel, and backlit illumination for efficiently monitoring engine coolant / water temperature. Installation hardware included. Additional adapters sold separately.
-
Labodam
Solidifying point constant temperature water bath, freezing point tester, distillate fuel cold filter plugging point filter, solidifying point tester, pour and cloud point tester, solidifying point and cold filter plugging point tester, multifunctional low temperature tester, automatic pour point tester.
-
HPM110 -
Webster Instruments
The HPM110 digital pressure gauge is designed for continuous monitoring of oil, water, hydraulic and other pressure media in mobile equipment, industrial hydraulics, and process control equipment.
-
Endress+Hauser AG
Flow measurement for liquids, gases and steam. Consistent product quality, safety, process optimization and environmental protection – these are only a few reasons why industrial flow measurement is becoming more important all the time. Water, natural gas, steam, mineral oil, chemicals are some of the fluids that have to be measured day in, day out.
-
LSC-Series -
Napco Precision Instruments Co
Moisture Analyzer is configured on the basis of high-precision electronic balance weighing sensor and high-efficiency secondary heat radiation device, Moisture analyzer can achieve rapid and accurate determination of the water. Moisture analyzer is a thermodynamic theory based on the material after drying by the weight and wet weight than the percentage of access to content and gouache other results.
