Filter Results By:
Products
Applications
Manufacturers
Noise Sources
create signal disturbances for the purpose of noise instrument calibration.
See Also: Pink Noise, Noise Generators
- Applied Instruments, Inc.
product
RF Noise Source
NS-3
The NS-3 Broadband RF Noise Generator provides an extremely flat AWGN (Additive White Gaussian Noise) signal from 5 to 2150 MHz. The output level adjusts in 0.1 dB steps over a 30 dB range.The bench-top configuration is standard and an optional two unit rack enclosure is available. The RS232 or USB remote control interface simplifies its use in automated test and factory ATE environments. The NS-3's combination of range, versatility and value make it the ideal general purpose broad-spectrum signal source for bench and ATE applications, including C/N, BER, MER, PER testing and rain fade simulation.
-
-
-
-
product
Noise Sources
NC1126A
This noise source by Noisecom produces white Gaussian noise up to +13 dBm. It contains a hermetically packaged noise diode that has been pre-selected for special performance characteristics. This module is ideal for many different applications including CATV, Secure communications, Jamming systems, OC-192 Testing, EW & EC.
-
product
Noise Sources
NC1128A
This noise source by Noisecom produces white Gaussian noise up to +13 dBm. It contains a hermetically packaged noise diode that has been pre-selected for special performance characteristics. This module is ideal for many different applications including CATV, Secure communications, Jamming systems, OC-192 Testing, EW & EC.
-
product
Noise Sources
WGNS
The system allows the user to extend the frequency range of the NFA to allow for accurate noise figure measurements to be performed on a device operating in the 26.5 – 170GHz range on wafer as well as in benchtop applications. Farran offers the WGNS series of noise sources to be used in conjunction with the FBC down converters for use as frequency extenders for noise figure measurement test system.
-
product
Noise Sources
The Keysight 346, 347 and SNS Series of noise sources work in conjunction with the NFA Series noise-figure analyzers to make noise-figure measurements from 10 MHz to 50 GHz.
-
product
Noise Sources
NC3208
It offers a high ENR output AWGN noise over a wide frequency range. This Noisecom noise source has excellent stability with temperature and voltage for tough environments. It contains a hermetically packaged noise diode that has been pre-selected for special performance characteristics. This module is ideal for many different applications including radar warning receivers (RWR), built-in test equipment (BITE), military aircraft, and Wi-Fi.
-
product
Noise Source
MNS-1
Matrix Test Equipment Incorporated
The MNS-1 is a shaped noise source that can be used toemulate 2 bands of digital carriers. While it does not havethe necessary attributes to generate a constellation, it doesmimic the loading of QAM carriers. The MNS-2 featuresremotely controllable 6 MHz wide notch filters to allowintroducing a QAM carrier capable of generating a constellationand enabling measurement of Modulation Error Ratio (MER) andBit Error Rate (BER).
-
product
Noise Sources
This power amplifier ensures that you get the maximum sound pressure level out of the Norsonic range of speakers.
-
-
-
-
product
Noise Source Family
346 Series
This series of broadband noise sources has been designed to cover the majority of measurement applications with a range of frequencies, Excess Noise Ratio (ENR) and coaxial connector types.
-
product
Noise Source Family
347
The R347B waveguide noise source cover the R-band (26.5 to 40 GHz frequency range), while the Q347B model cover the Q-band (33 to 50 GHz frequency range), allows you to make accurate noise figure measurements on millimeter-wave devices.
-
product
Noise Figure Analyzers & Noise Sources
Keysight Technologies provide a range of noise figure measurements solutions to meet your needs, from the NFA series noise figure analyzers to the noise figure measurement personalities for our spectrum analyzers. We also have a range of noise sources to complete the measurement solution.
-
product
Surface-Mount Noise Sources
Mercury’s family of surface-mount noise sources provides exceptional performance in a compact and easy to integrate package. These products are ideal for applications such built-in test and dithering circuits where the system requirements drive a need for compact, surface mount technology.
-
product
High-Power Noise Sources
These modules not only contain the noise diode circuitry, but also gain stages to boost the output power. While lower frequencies (under 2 GHz) are most common, Mercury produces powerful amplified noise modules up to 18 GHz. Noise modules are available in coaxial, surface mount and pin type construction. TTL control options are available.
-
product
Noise Source Family
SNS Series
Works in conjunction with the NFA Series of noise figure analyzers to simplify measurement set-up and improve accuracy and reliability, automatically downloading electronically stored calibration data.
-
product
Microwave Noise Source Generators
Advanced Technical Materials, Inc.
Noise Sources supply white gaussian electronic noise. The output is a flat instantaneous broadband electronic random noise. The noise source converts a DC input to noise. Units are available in bands between 10MHz thru 26.5 Ghz.
-
-
product
Precision Calibrated Noise Sources
ELVA-1's calibrated noise source ISSN-XX series delivers a uniform level of noise power spectral density within the whole waveguide frequency range. Sources are available in eight waveguide bands covering 26.4-170 GHz.
-
product
High Power Noise Sources
NS-7001
The NS-7001 is high-power noise source specifically designed to operate in the 2.11-2.17 GHz UMTS band. It features flat output power that is regulated over a wide temperature range with high rejection outside the operating band of interest. Logic control is provided to enable/disable the noise source and an internal BIT function continuously monitors the output power. Other frequency bands and power levels are available.
-
product
Broadband Calibrated Noise Sources
Fairview Microwave’s calibrated noise sources cover frequency bands from 10 KHz to 18 GHz. Their performance specifications include output ENR levels ranging from 15 dB to 30 dB and typical VSWR levels as low as 1.25:1. Depending on the model, calibrated frequency points are at 10 MHz, 100 MHz, 1000 MHz, 2000 MHz and 1 GHz steps. The temperature coefficient of these noise sources is < 0.01 dB/°C and noise output variation is < 0.1 dB/%V.
-
product
Fullband Coaxial Noise Sources
Our line of full-band noise sources are specially designed for easy integration into microwave systems. They feature rugged construction with excellent long-term stability. In addition to the RF output choices, there are also different packages available to meet a wide range of mechanical constraints. Typical applications include jamming, radar alignment, SNR testing and general lab use.
-
product
Broadband Coaxial Noise Sources
Our integrated noise modules contain all the required biasing circuitry and only need a positive voltage to activate for an easy installation. Since they typically do not contain amplification, the raw noise output from the diode is seen at the output of the module resulting in a maximum ENR of approximately 35dB. Primary applications include system built-in test and laboratory use.
-
product
Calibrated, Integral Isolator Noise Sources
Calibrated, Integral Isolator Noise Sources by Pasternack
-
product
Low Phase Noise Reference Source
96270A
The 96270A RF Reference Source is the simplest, most accurate and cost-effective single instrument for calibrating spectrum analyzers and RF power sensors and more, up to 27 GHz.
-
product
Microphone Array System for Noise Source Identification
Noise source identification of large-scale machinery is a tough issue. If you don’t know the noise source, you cannot find out methods of improving you products. Microphone array, or acoustic camera, is an advanced technology for noise source identification in steady, non-steady, motion, or rest state. A microphone array system can display noise source distribution in real time, and identify the locations of noise source inside the equipment
